Reimplement hardreset according to the datasheet.  The old hardreset
didn't reset controller status and the controller might not be ready
after reset.  Also, as SStatus is a bit flakey after hardreset,
sata_std_hardrset() didn't use to wait long enough before proceeding.

Note that as we're not depending on SStatus, DET==1 condition cannot
be used to wait for link, so use shorter timeout for no device case.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Nothing, not the datasheet nor the errats, says this delay is
necessary and with the previous PORT_CS_INIT change, we know the
controller is in good state.  Kill 10ms sleep.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure the controller has no pending commands and ready for command
before issuing SRST.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement sil24_init_port which performs port initialization via
PORT_CS_INIT.  To be used later by softreset and EH.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

SiI3124 might lose completion interrupt if completion interrupt occurs
shortly after SLOT_STAT register is read for the previous completion
interrupt if it is operating in PCI-X mode.

This currently doesn't trigger as libata never queues more than one
command, but it will with NCQ changes.  This patch implements the
workaround - turning on WoC and explicitly clearing interrupt.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All sil24 controllers share the same host flags except for NPORTS.
Consolidate them into SIL24_COMMON_FLAGS.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add HOST_CTRL_* and more PORT_IRQ_* bits.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename PORT_IRQ_SDB_FIS to more proper PORT_IRQ_SDB_NOTIFY.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Type fix.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Replace hard-coded waiting loops in sata_sil24 to ata_wait_register().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Improve softreset error message.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sil24_softreset calculated timeout by adding ATA_TMOUT_BOOT * HZ to
jiffies; however, as ATA_TMOUT_BOOT is already in jiffies, multiplying
by HZ makes the value way off.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make reset methods complain loud when they fail.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port.  However, muting
failure message isn't the correct approach.  Reset methods are
responsible for detecting no device condition and finishing
successfully.  Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.

Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rename ATA_FLAG_PORT_DISABLED to ATA_FLAG_DISABLED for consistency.
(ATA_FLAG_* are always about ports).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mostly, trim trailing whitespace.

Also:
* export ata_dev_pair
* move ata_dev_classify export closer to ata_dev_pair export

* libata will soon move to iomap, so we should use
  pci_iomap() and pci_iounmap().
* Use kzalloc() where appropriate.

SCSI midlayer has moved hostt->eh_timed_out to transport template.  As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata.  No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

sil24 softreset timeout was > 100ms (100 loops with msleep(1)), which
turned out to be too short for some devices (ASI ARAID99 2000).  This
patch converts sil24 softreset waiting loop to use proper timeout
condition and lengthen the timeout to ATA_TMOUT_BOOT secs and check
interval to 100ms.  Chisato Yamauchi discovered the problem and
supplied initial patch.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Chisato Yamauchi <cyamauch@plamo.linet.gr.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

sata_sil24 softreset routine used to check sata_dev_present() after
SRST is complete in the hope that SRST may do some good even when
SStatus reports no device.  This is okay as long as SRST timeout is
short (> 100ms in the current code) but it seems that not all SATA
devices are happy with short SRST timeout.

This patch makes softreset exit early without performing actual SRST
if SStatus reports no device in preparation for lengthening SRST
timeout.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

mwdma_mask was not copied from port_info to probe_ent.  Fix it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a new PCI ID for SiI 3124.  Reported by Silicon Image.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

cdb_len is per-device property.  Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging.  This patch
makes cdb_len per-device.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Now that libata is smart enough to handle both soft and hard resets,
add hardreset method.  Note that sil24 hardreset doesn't supply
signature; still, the new reset mechanism can make good use of it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Convert sata_sil24 ->phy_reset to new reset mechanism.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

->eng_timeout cannot be invoked with NULL qc anymore.  Add an
assertion in ata_scsi_error() and kill NULL qc handling from all
->eng_timeout callbacks.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Make all libata low level drivers use ata_scsi_timed_out().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Implement ata_eh_qc_complete/retry() using scsi_eh_finish_cmd() and
scsi_eh_flush_done_q().  This removes all eh scsicmd finish hacks from
low level drivers.

This change was first suggested by Jeff Garzik.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Return AC_ERR_* mask from issue fuctions instead of 0/-1.  This
enables things like failing a qc with AC_ERR_HSM when the device
doesn't set DRDY when the qc is about to be issued.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add detailed AC_ERR_* flags and use them.  Long-term goal is to
describe all errors with err_mask and tf combination (tf for failed
sector information, etc...).  After proper error diagnosis is
implemented, sense data should also be generated from err_mask instead
of directly from hardware tf registers as it is currently.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Reflect changes in SCSI midlayer and updated to use new
ordered request implementation
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJens Axboe <axboe@suse.de>

  - remove err_mask from the parameter list of the complete functions
  - move err_mask to ata_queued_cmd
  - initialize qc->err_mask when needed
  - for each function call to ata_qc_complete(), replace the err_mask parameter with qc->err_mask.
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>

===============
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

sil24_error_intr logs all error interrupts.  ATAPI devices generates
many harmless errors which can be ignored and all serious ones are
reported via sense data by SCSI layer.  Don't log device errors from
ATAPI devices.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch implements ATAPI support for sil24 and bumps driver version
to 0.23.
Signed-off-by: NTejun Heo <htejun@gmail.com>

--

Jeff, it has been converted to use ->dev_config as pointed out.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

There seems to be no way to obtain device signature from sil24 after
SATA phy reset and SRST is needed anyway for later port multiplier
suppport.  This patch converts sil24_phy_reset to use SRST instaed.
Signed-off-by: NTejun Heo <htejun@gmail.com>

--

Jeff, I didn't remove the 10ms sleep just to be on the safe side.  I
think we can live with 10ms sleep on SRST.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When an error condition is raised by device via D2H FIS or SDB.  sil24
controller should be restarted by setting PORT_CS_INIT and waiting
until PORT_CS_RDY is asserted instead of resetting the controller.
This patch implements sil24_restart_controller for those cases.  This
patch also makes sure that PORT_CS_RDY is asserted on
sil24_reset_controller completion.
Signed-off-by: NTejun Heo <htejun@gmail.com>

--

Jeff, delay is reduced to 1us and cnt increased to 10k.  My sil3124
turns on PORT_CS_RDY on the second iteration even without any delay.
I think 10k * 1us should be more than enough.

I tried to convert both restart and reset to use msleep's with work
queue, but if we do that, host_set lock should be released after
initiating restart or reset, leading to race condition among
reset/restart, other interrupts and timeout.  Implementing
synchronization among those in low-level driver doesn't seem right.
Well, reduced timeout should work for the time being.

Thanks.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Adds constants for ATAPI support to sata_sil24.  This patch is
originally from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>