Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 10 3月, 2017 3 次提交
  3. 03 12月, 2016 1 次提交
  5. 16 11月, 2016 1 次提交
  7. 27 9月, 2016 4 次提交
    • P
      net: bcmgenet: use new api ethtool_{get|set}_link_ksettings · fa92bf04
      由 Philippe Reynes 提交于 
      The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fa92bf04
    • F
      Revert "net: ethernet: bcmgenet: use phydev from struct net_device" · 0299b6ac
      由 Florian Fainelli 提交于 
      This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0299b6ac
    • P
      Revert "net: ethernet: bcmgenet: use new api ethtool_{get|set}_link_ksettings" · 62c8d3da
      由 Philippe Reynes 提交于 
      This reverts commit 6b352ebc ("net: ethernet: broadcom: bcmgenet:
use new api ethtool_{get|set}_link_ksettings").

We needs to revert the commit 62469c76 ("net: ethernet: bcmgenet:
use phydev from struct net_device"), because this commit add a
regression. As the commit 6b352ebc ("net: ethernet: broadcom:
bcmgenet: use new api ethtool_{get|set}_link_ksettings") depend
on the first one, we also need to revert it first.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      62c8d3da
    • F
      Revert "net: ethernet: bcmgenet: use phydev from struct net_device" · bf1a85a8
      由 Florian Fainelli 提交于 
      This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bf1a85a8
  9. 26 9月, 2016 1 次提交
  11. 20 9月, 2016 1 次提交
  13. 01 9月, 2016 1 次提交
    • J
      net: bcmgenet: constify ethtool_ops structures · 70591ab9
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      70591ab9
  15. 12 7月, 2016 1 次提交
  17. 05 7月, 2016 2 次提交
  19. 05 5月, 2016 1 次提交
  21. 17 4月, 2016 1 次提交
  23. 14 4月, 2016 3 次提交
  25. 06 4月, 2016 3 次提交
  27. 25 3月, 2016 2 次提交
    • P
      net: bcmgenet: fix skb_len in bcmgenet_xmit_single() · 7dd39913
      由 Petri Gynther 提交于 
      skb_len needs to be skb_headlen(skb) in bcmgenet_xmit_single().

Fragmented skbs can have only Ethernet + IP + TCP headers (14+20+20=54 bytes)
in the linear buffer, followed by the rest in fragments. Bumping skb_len to
ETH_ZLEN would be incorrect for this case, as it would introduce garbage
between TCP header and the fragment data.

This also works with regular/non-fragmented small packets < ETH_ZLEN bytes.
Successfully tested this on GENETv3 with 42-byte ARP frames.

For testing, I used:
ethtool -K eth0 tx-checksum-ipv4 off
ethtool -K eth0 tx-checksum-ipv6 off
echo 0 > /proc/sys/net/ipv4/tcp_timestamps

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NPetri Gynther <pgynther@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7dd39913
    • P
      net: bcmgenet: fix dev->stats.tx_bytes accounting · 55868120
      由 Petri Gynther 提交于 
      1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect
   transmitted bytes. dev->stats updates can then be moved outside the
   while-loop. bytes_compl is also needed for future BQL support.
2. When bcmgenet device uses Tx checksum offload, each transmitted skb
   gets an extra 64-byte header prepended to it. Before this header is
   prepended to the skb, we need to save the skb "wire" length in
   GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can
   be done in __bcmgenet_tx_reclaim().
3. skb->len covers the entire length of skb, whether it is linear or
   fragmented. Thus, when we clean the fragments, do not increase
   transmitted bytes.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      55868120
  29. 19 3月, 2016 1 次提交
  31. 20 2月, 2016 1 次提交
  33. 19 11月, 2015 1 次提交
  35. 02 11月, 2015 1 次提交
  37. 19 10月, 2015 1 次提交
    • F
      net: bcmgenet: Fix early link interrupt enabling · 37850e37
      由 Florian Fainelli 提交于 
      Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.

Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.

Fixes: 6cc8e6d4 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      37850e37
  39. 16 10月, 2015 1 次提交
  41. 22 9月, 2015 2 次提交
  43. 18 9月, 2015 2 次提交
    • F
      net: bcmgenet: Implement RX coalescing control knobs · 4a29645b
      由 Florian Fainelli 提交于 
      Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.

We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4a29645b
    • F
      net: bcmgenet: Implement TX coalescing control knobs · 2f913070
      由 Florian Fainelli 提交于 
      Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.

We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.

Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.

While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2f913070
  45. 24 8月, 2015 2 次提交
  47. 01 8月, 2015 1 次提交
  49. 27 7月, 2015 1 次提交
  51. 21 7月, 2015 1 次提交