Those functions are going to be used even after inode cache is removed
so moved them to a more appropriate place.
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Since commit 72deb455 ("block: remove CONFIG_LBDAF") (5.2) the
sector_t type is u64 on all arches and configs so we don't need to
typecast it.  It used to be unsigned long and the result of sector size
shifts were not guaranteed to fit in the type.
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Superblock (and its copies) is the only data structure in btrfs which
has a fixed location on a device. Since we cannot overwrite in a
sequential write required zone, we cannot place superblock in the zone.
One easy solution is limiting superblock and copies to be placed only in
conventional zones.  However, this method has two downsides: one is
reduced number of superblock copies. The location of the second copy of
superblock is 256GB, which is in a sequential write required zone on
typical devices in the market today.  So, the number of superblock and
copies is limited to be two.  Second downside is that we cannot support
devices which have no conventional zones at all.

To solve these two problems, we employ superblock log writing. It uses
two adjacent zones as a circular buffer to write updated superblocks.
Once the first zone is filled up, start writing into the second one.
Then, when both zones are filled up and before starting to write to the
first zone again, it reset the first zone.

We can determine the position of the latest superblock by reading write
pointer information from a device. One corner case is when both zones
are full. For this situation, we read out the last superblock of each
zone, and compare them to determine which zone is older.

The following zones are reserved as the circular buffer on ZONED btrfs.

- The primary superblock: zones 0 and 1
- The first copy: zones 16 and 17
- The second copy: zones 1024 or zone at 256GB which is minimum, and
  next to it

If these reserved zones are conventional, superblock is written fixed at
the start of the zone without logging.
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Placing both data and metadata in a block group is impossible in ZONED
mode. For data, we can allocate a space for it and write it immediately
after the allocation. For metadata, however, we cannot do that, because
the logical addresses are recorded in other metadata buffers to build up
the trees. As a result, a data buffer can be placed after a metadata
buffer, which is not written yet. Writing out the data buffer will break
the sequential write rule.

Check and disallow MIXED_BG with ZONED mode.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Reviewed-by: NAnand Jain <anand.jain@oracle.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

fallocate() is implemented by reserving actual extent instead of
reservations. This can result in exposing the sequential write
constraint of host-managed zoned block devices to the application, which
would break the POSIX semantic for the fallocated file.  To avoid this,
report fallocate() as not supported when in ZONED mode for now.

In the future, we may be able to implement "in-memory" fallocate() in
ZONED mode by utilizing space_info->bytes_may_use or similar, so this
returns EOPNOTSUPP.
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Reviewed-by: NAnand Jain <anand.jain@oracle.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

NODATACOW implies overwriting the file data on a device, which is
impossible in sequential required zones. Disable NODATACOW globally with
mount option and per-file NODATACOW attribute by masking FS_NOCOW_FL.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

As updates to the space cache v1 are in-place, the space cache cannot be
located over sequential zones and there is no guarantees that the device
will have enough conventional zones to store this cache. Resolve this
problem by disabling completely the space cache v1.  This does not
introduce any problems with sequential block groups: all the free space
is located after the allocation pointer and no free space before the
pointer.  There is no need to have such cache.

Note: we can technically use free-space-tree (space cache v2) on ZONED
mode. But, since ZONED mode now always allocates extents in a block
group sequentially regardless of underlying device zone type, it's no
use to enable and maintain the tree.

For the same reason, NODATACOW is also disabled.

In summary, ZONED will disable:

| Disabled features | Reason                                              |
|-------------------+-----------------------------------------------------|
| RAID/DUP          | Cannot handle two zone append writes to different   |
|                   | zones                                               |
|-------------------+-----------------------------------------------------|
| space_cache (v1)  | In-place updating                                   |
| NODATACOW         | In-place updating                                   |
|-------------------+-----------------------------------------------------|
| fallocate         | Reserved extent will be a write hole                |
|-------------------+-----------------------------------------------------|
| MIXED_BG          | Allocated metadata region will be write holes for   |
|                   | data writes                                         |
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

The zone append write command has a maximum IO size restriction it
accepts. This is because a zone append write command cannot be split, as
we ask the device to place the data into a specific target zone and the
device responds with the actual written location of the data.

Introduce max_zone_append_size to zone_info and fs_info to track the
value, so we can limit all I/O to a zoned block device that we want to
write using the zone append command to the device's limits.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Introduce function btrfs_check_zoned_mode() to check if ZONED flag is
enabled on the file system and if the file system consists of zoned
devices with equal zone size.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NDamien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

If a zoned block device is found, get its zone information (number of
zones and zone size).  To avoid costly run-time zone report
commands to test the device zones type during block allocation, attach
the seq_zones bitmap to the device structure to indicate if a zone is
sequential or accept random writes. Also it attaches the empty_zones
bitmap to indicate if a zone is empty or not.

This patch also introduces the helper function btrfs_dev_is_sequential()
to test if the zone storing a block is a sequential write required zone
and btrfs_dev_is_empty_zone() to test if the zone is a empty zone.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Reviewed-by: NAnand Jain <anand.jain@oracle.com>
Signed-off-by: NDamien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

This patch introduces the ZONED incompat flag. The flag indicates that
the volume management will satisfy the constraints imposed by
host-managed zoned block devices (aligned chunk allocation, append-only
updates, reset zone after filled).

As the zoned support will happen incrementally due to enhancing some
core infrastructure like super block writes, tree-log, raid support, the
feature will appear in sysfs only on debug builds. It will be enabled
once the support is feature complete and applications can reliably check
whether zoned support is present or not.
Reviewed-by: NAnand Jain <anand.jain@oracle.com>
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NDamien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: NNaohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Results in slightly smaller code.

add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-11 (-11)
Function                                     old     new   delta
btrfs_should_end_transaction                  96      85     -11
Total: Before=20070, After=20059, chg -0.05%
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

It simply gets assigned to 'ret' in case of errors. The flow of the
while loop is not changed by this commit since the few call sites
that 'goto next' will simply break from the loop.
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

In most cases when an error is returned from a function 'ret' is simply
assigned to 'err'. There is only one case where walk_up_reloc_tree can
return a positive value - in this case the code breaks from the loop and
ret is going to get its return value from btrfs_cow_block - either 0 or
negative. This retains the old logic of how 'err' used to be set at
this call site.
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Use only a single 'ret' to control whether we should abort the
transaction or not. That's fine, because if we abort a transaction then
btrfs_end_transaction will return the same value as passed to
btrfs_abort_transaction. No semantic changes.
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

When we are attempting to start writeback for an existing extent in NOCOW
mode, at run_delalloc_nocow(), we must check if the extent is shared, and
if it is, fallback to a COW write. However we do such check while still
holding a read lock on the leaf that contains the file extent item, and
that check, the call to btrfs_cross_ref_exist(), can take some time
because:

1) It needs to do a search on the extent tree, which obviously takes some
   time, specially if delayed references are being run at the moment, as
   we can block when trying to lock currently write locked btree nodes;

2) It needs to check the delayed references for any existing reference
   for our data extent, this requires acquiring the delayed references'
   spinlock and maybe block on the mutex of a delayed reference head in the
   case where there is a delayed reference for our data extent, in the
   worst case it makes us release the path on the extent tree and retry
   the whole process again (going back to step 1).

There are other operations we do while holding the leaf locked that can
take some significant time as well (specially all together):

* btrfs_extent_readonly() - to check if the block group containing the
  extent is currently in RO mode. This requires taking a spinlock and
  searching for the block group in a rbtree that can be big on large
  filesystems;

* csum_exist_in_range() - to search if there are any checksums in the
  csum tree for the extent. Like before, this can take some time if we are
  in a filesystem that has both COW and NOCOW files, in which case the
  csum tree is not empty;

* btrfs_inc_nocow_writers() - increment the number of nocow writers in the
  block group that contains the data extent. Needs to acquire a spinlock
  and search for the block group in a rbtree that can be big on large
  filesystems.

So just unlock the leaf (release the path) before doing all those checks,
since we do not need it anymore. In case we can not do a NOCOW write for
the extent, due to any of those checks failing, and the writeback range
goes beyond that extents' length, we will do another btree search for the
next file extent item.

The following script that calls dbench was used to measure the impact of
this change on a VM with 8 CPUs, 16Gb of ram, using a raw NVMe device
directly (no intermediary filesystem on the host) and using a non-debug
kernel (default configuration on Debian):

  $ cat test-dbench.sh
  #!/bin/bash

  DEV=/dev/sdk
  MNT=/mnt/sdk
  MOUNT_OPTIONS="-o ssd -o nodatacow"
  MKFS_OPTIONS="-m single -d single"

  mkfs.btrfs -f $MKFS_OPTIONS $DEV
  mount $MOUNT_OPTIONS $DEV $MNT

  dbench -D $MNT -t 300 64

  umount $MNT

Before this change:

 Operation      Count    AvgLat    MaxLat
 ----------------------------------------
 NTCreateX    9326331     0.317   399.957
 Close        6851198     0.002     6.402
 Rename        394894     2.621   402.819
 Unlink       1883131     0.931   398.082
 Deltree          256    19.160   303.580
 Mkdir            128     0.003     0.016
 Qpathinfo    8452314     0.068   116.133
 Qfileinfo    1481921     0.001     5.081
 Qfsinfo      1549963     0.002     4.444
 Sfileinfo     759679     0.084    17.079
 Find         3268168     0.396   118.196
 WriteX       4653310     0.056   110.993
 ReadX        14618818     0.005    23.314
 LockX          30364     0.003     0.497
 UnlockX        30364     0.002     1.720
 Flush         653619    16.954   569.299

Throughput 966.651 MB/sec  64 clients  64 procs  max_latency=569.377 ms

After this change:

 Operation      Count    AvgLat    MaxLat
 ----------------------------------------
 NTCreateX    9710433     0.302   232.449
 Close        7132948     0.002    11.496
 Rename        411144     2.452   131.805
 Unlink       1960961     0.893   230.383
 Deltree          256    14.858   198.646
 Mkdir            128     0.002     0.005
 Qpathinfo    8800890     0.066   111.588
 Qfileinfo    1542556     0.001     3.852
 Qfsinfo      1613835     0.002     5.483
 Sfileinfo     790871     0.081    19.492
 Find         3402743     0.386   120.185
 WriteX       4842918     0.054   179.312
 ReadX        15220407     0.005    32.435
 LockX          31612     0.003     1.533
 UnlockX        31612     0.002     1.047
 Flush         680567    16.320   463.323

Throughput 1016.59 MB/sec  64 clients  64 procs  max_latency=463.327 ms

+5.0% throughput, -20.5% max latency

Also, the following test using fio was run:

  $ cat test-fio.sh
  #!/bin/bash

  DEV=/dev/sdk
  MNT=/mnt/sdk
  MOUNT_OPTIONS="-o ssd -o nodatacow"
  MKFS_OPTIONS="-d single -m single"

  if [ $# -ne 4 ]; then
      echo "Use $0 NUM_JOBS FILE_SIZE FSYNC_FREQ BLOCK_SIZE"
      exit 1
  fi

  NUM_JOBS=$1
  FILE_SIZE=$2
  FSYNC_FREQ=$3
  BLOCK_SIZE=$4

  cat <<EOF > /tmp/fio-job.ini
  [writers]
  rw=randwrite
  fsync=$FSYNC_FREQ
  fallocate=none
  group_reporting=1
  direct=0
  bs=$BLOCK_SIZE
  ioengine=sync
  size=$FILE_SIZE
  directory=$MNT
  numjobs=$NUM_JOBS
  EOF

  echo
  echo "Using fio config:"
  echo
  cat /tmp/fio-job.ini
  echo
  echo "mount options: $MOUNT_OPTIONS"
  echo

  mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
  mount $MOUNT_OPTIONS $DEV $MNT

  echo "Creating nodatacow files before fio runs..."
  for ((i = 0; i < $NUM_JOBS; i++)); do
      xfs_io -f -c "pwrite -b 128M 0 $FILE_SIZE" "$MNT/writers.$i.0"
  done
  sync

  fio /tmp/fio-job.ini
  umount $MNT

Before this change:

$ ./test-fio.sh 16 512M 2 4K
(...)
WRITE: bw=28.3MiB/s (29.6MB/s), 28.3MiB/s-28.3MiB/s (29.6MB/s-29.6MB/s), io=8192MiB (8590MB), run=289800-289800msec

After this change:

$ ./test-fio.sh 16 512M 2 4K
(...)
WRITE: bw=31.2MiB/s (32.7MB/s), 31.2MiB/s-31.2MiB/s (32.7MB/s-32.7MB/s), io=8192MiB (8590MB), run=262845-262845msec

+9.7% throughput, -9.8% runtime
Signed-off-by: NFilipe Manana <fdmanana@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

The tree checker is called many times as it verifies metadata at
read/write time. The checks follow a simple pattern:

  if (error_condition) {
	  report_error();
	  return -EUCLEAN;
  }

All the error reporting functions are annotated as __cold that is
supposed to hint the compiler to move the statement block out of the hot
path. This does not seem to happen that often.

As the error condition is expected to be false almost always, we can
annotate it with 'unlikely' as this satisfies one of the few use cases
for the annotation. The expected outcome is a stronger hint to compiler
to reorder the checks

  test
  jump to exit
  test
  jump to exit
  ...

which can be observed in asm of eg. check_dir_item,
btrfs_check_chunk_valid, check_root_item or check_leaf.

There's a measurable run time improvement reported by Josef, the testing
workload went from 655 MiB/s to 677 MiB/s, which is about +3%.

There should be no functional changes but some of the conditions have
been rewritten to produce more readable result, some lines are longer
than 80, for the sake of readability.
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Without a NULL fs_info the helpers will print something like

	BTRFS error (device <unknown>): ...

This can happen in contexts where fs_info is not available at all or
it's potentially unsafe due to object lifetime. The <unknown> stub does
not bring much information and with the prefix makes the message
unnecessarily longer.

Remove it for the NULL fs_info case.

	BTRFS error: ...

Callers can add the device information to the message itself if needed.
Reviewed-by: NAnand Jain <anand.jain@oracle.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

In alloc_extent_buffer(), after we got a page from btree inode, we check
if that page has private pointer attached.

If attached, we check if the existing extent buffer has proper refs.
If not (the eb is being freed), we will detach that private eb pointer.

The point here is, we are detaching that eb pointer by calling:
- ClearPagePrivate()
- put_page()

The put_page() here is especially confusing, as it's decreasing the ref
from attach_page_private().  Without knowing that, it looks like the
put_page() is for the find_or_create_page() call, confusing the reader.

Since we're always modifying page private with attach_page_private() and
detach_page_private(), the only open-coded detach_page_private() here is
really confusing.

Fix it by calling detach_page_private().
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

In btrfs_lookup_bio_sums() if the bio is pretty large, we want to
start readahead in the csum tree.

However the threshold is an immediate number, (PAGE_SIZE * 8), from the
initial btrfs merge.

The meaning of the value is pretty hard to guess, especially when the
immediate number is from the times when 4K sectorsize was the default
and only CRC32C was supported.

For the most common btrfs setup, CRC32 csum and 4K sectorsize,
it means just 32K read would kick readahead, while the csum itself is
only 32 bytes in size.

Now let's be more reasonable by taking both csum size and node size into
consideration.

If the csum size for the bio is larger than one leaf, then we kick the
readahead.  This means for current default btrfs, the threshold will be
16M.

This change should not change performance observably, thus this is
mostly a readability enhancement.
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

extent_invalidatepage() will try to clear all possible bits since it's
calling clear_extent_bit() with delete == 1.

This is currently fine, since for btree io tree, it only utilizes
EXTENT_LOCK bit.  But this could be a problem for later subpage support,
which will utilize extra io tree bit to represent additional info.

This patch will just convert that clear_extent_bit() to
unlock_extent_cached().

For current code since only EXTENT_LOCKED bit is utilized, this doesn't
change the behavior, but provides a much cleaner basis for incoming
subpage support.
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Parameter @phy_offset is the offset against the bio->bi_iter.bi_sector.
@phy_offset is mostly for data io to lookup the csum in btrfs_io_bio.

But for metadata, it's completely useless as metadata stores their own
csum in its header, so we can remove it.

Note: parameters @start and @end, they are not utilized at all for
current sectorsize == PAGE_SIZE case, as we can grab eb directly from
page.

But those two parameters are very important for later subpage support,
thus @start/@len are not touched here.
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

That anonymous structure serve no special purpose, just replace it with
regular members.
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Currently the type is unsigned int which could change its width
depending on the architecture. We need up to 32 bits so make it
explicit.
Reviewed-by: NNikolay Borisov <nborisov@suse.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Introduce a new helper to handle update page status in
end_bio_extent_readpage(). This will be later used for subpage support
where the page status update can be more complex than now.
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

In end_bio_extent_readpage() we had a strange dance around
extent_start/extent_len.

Hidden behind the strange dance is, it's just calling
endio_readpage_release_extent() on each bvec range.

Here is an example to explain the original work flow:

  Bio is for inode 257, containing 2 pages, for range [1M, 1M+8K)

  end_bio_extent_extent_readpage() entered
  |- extent_start = 0;
  |- extent_end = 0;
  |- bio_for_each_segment_all() {
  |  |- /* Got the 1st bvec */
  |  |- start = SZ_1M;
  |  |- end = SZ_1M + SZ_4K - 1;
  |  |- update = 1;
  |  |- if (extent_len == 0) {
  |  |  |- extent_start = start; /* SZ_1M */
  |  |  |- extent_len = end + 1 - start; /* SZ_1M */
  |  |  }
  |  |
  |  |- /* Got the 2nd bvec */
  |  |- start = SZ_1M + 4K;
  |  |- end = SZ_1M + 4K - 1;
  |  |- update = 1;
  |  |- if (extent_start + extent_len == start) {
  |  |  |- extent_len += end + 1 - start; /* SZ_8K */
  |  |  }
  |  } /* All bio vec iterated */
  |
  |- if (extent_len) {
     |- endio_readpage_release_extent(tree, extent_start, extent_len,
				      update);
	/* extent_start == SZ_1M, extent_len == SZ_8K, uptodate = 1 */

As the above flow shows, the existing code in end_bio_extent_readpage()
is accumulates extent_start/extent_len, and when the contiguous range
stops, calls endio_readpage_release_extent() for the range.

However current behavior has something not really considered:

- The inode can change
  For bio, its pages don't need to have contiguous page_offset.
  This means, even pages from different inodes can be packed into one
  bio.

- bvec cross page boundary
  There is a feature called multi-page bvec, where bvec->bv_len can go
  beyond bvec->bv_page boundary.

- Poor readability

This patch will address the problem:

- Introduce a proper structure, processed_extent, to record processed
  extent range

- Integrate inode/start/end/uptodate check into
  endio_readpage_release_extent()

- Add more comment on each step.
  This should greatly improve the readability, now in
  end_bio_extent_readpage() there are only two
  endio_readpage_release_extent() calls.

- Add inode check for contiguity
  Now we also ensure the inode is the same one before checking if the
  range is contiguous.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

In extent-io-test, there are two invalid tests:

- Invalid nodesize for test_eb_bitmaps()
  Instead of the sectorsize and nodesize combination passed in, we're
  always using hand-crafted nodesize, e.g:

	len = (sectorsize < BTRFS_MAX_METADATA_BLOCKSIZE)
		? sectorsize * 4 : sectorsize;

  In above case, if we have 32K page size, then we will get a length of
  128K, which is beyond max node size, and obviously invalid.

  The common page size goes up to 64K so we haven't hit that

- Invalid extent buffer bytenr
  For 64K page size, the only combination we're going to test is
  sectorsize = nodesize = 64K.
  However, in that case we will try to test an eb which bytenr is not
  sectorsize aligned:

	/* Do it over again with an extent buffer which isn't page-aligned. */
	eb = __alloc_dummy_extent_buffer(fs_info, nodesize / 2, len);

  Sector alignment is a hard requirement for any sector size.
  The only exception is superblock. But anything else should follow
  sector size alignment.

  This is definitely an invalid test case.

This patch will fix both problems by:

- Honor the sectorsize/nodesize combination
  Now we won't bother to hand-craft the length and use it as nodesize.

- Use sectorsize as the 2nd run extent buffer start
  This would test the case where extent buffer is aligned to sectorsize
  but not always aligned to nodesize.

Please note that, later subpage related cleanup will reduce
extent_buffer::pages[] to exactly what we need, making the sector
unaligned extent buffer operations cause problems.

Since only extent_io self tests utilize this, this patch is required for
all later cleanup/refactoring.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NQu Wenruo <wqu@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

A semicolon is not needed after a switch statement.
Signed-off-by: NTom Rix <trix@redhat.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

The function is needlessly convoluted. Fix that by:

* removing redundant sret variable definition in both if arms

* replace the again/done labels with direct return statements, the
  function is short enough and doesn't do anything special upon exit

* remove BUG_ON on split_node returning a positive number - it can't
  happen as split_node returns either 0 or a negative error code.
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

At the point when we set 'ret = 0' it's guaranteed that the function is
going to return 0 so directly return 0. No functional changes.
Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

At inode.c:cow_file_range_inline(), after we insert the inline extent
in the fs/subvolume btree, we call btrfs_drop_extent_cache() to drop
all extent maps in the file range, however that is not necessary because
we have already done it in the call to btrfs_drop_extents(), which calls
btrfs_drop_extent_cache() for us, and since at this point we have the file
range locked in the inode's iotree (we are in the writeback path), we know
no other task can come in and read stale file extent items or find none
and therefore create either stale extent maps or an extent map that
represents a hole.

So just remove that unnecessary call to btrfs_drop_extent_cache(), as it's
doing nothing and only wasting time. This call has been around since 2008,
introduced in commit c8b97818 ("Btrfs: Add zlib compression support"),
but even back then it seems it was not necessary, since we had the range
locked in the inode's iotree and the call to btrfs_drop_extents() already
used to always call btrfs_drop_extent_cache().
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NFilipe Manana <fdmanana@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

When joining a log transaction we acquire the root's log mutex, then
increment the root's log batch and log writers counters while holding
the mutex. However we don't need to increment the log batch there,
because we are holding the mutex and incremented the log writers counter
as well, so any other task trying to sync log will wait for the current
task to finish its logging and still achieve the desired log batching.

Since the log batch counter is an atomic counter and is incremented twice
at the very beginning of the fsync callback (btrfs_sync_file()), once
before flushing delalloc and once again after waiting for writeback to
complete, eliminating its increment when joining the log transaction
may provide some performance gains in case we have multiple concurrent
tasks doing fsyncs against different files in the same subvolume, as it
reduces contention on the atomic (locking the cacheline and bouncing it).

When testing fio with 32 jobs, on a 8 cores VM, doing fsyncs against
different files of the same subvolume, on top of a zram device, I could
consistently see gains (higher throughput) between 1% to 2%, which is a
very low value and possibly hard to be observed with a real device (I
couldn't observe consistent gains with my low/mid end NVMe device).
So this change is mostly motivated to just simplify the logic, as updating
the log batch counter is only relevant when an fsync starts and while not
holding the root's log mutex.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NFilipe Manana <fdmanana@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Every time we log an inode we lookup in the fs/subvol tree for xattrs and
if we have any, log them into the log tree. However it is very common to
have inodes without any xattrs, so doing the search wastes times, but more
importantly it adds contention on the fs/subvol tree locks, either making
the logging code block and wait for tree locks or making the logging code
making other concurrent operations block and wait.

The most typical use cases where xattrs are used are when capabilities or
ACLs are defined for an inode, or when SELinux is enabled.

This change makes the logging code detect when an inode does not have
xattrs and skip the xattrs search the next time the inode is logged,
unless the inode is evicted and loaded again or a xattr is added to the
inode. Therefore skipping the search for xattrs on inodes that don't ever
have xattrs and are fsynced with some frequency.

The following script that calls dbench was used to measure the impact of
this change on a VM with 8 CPUs, 16Gb of ram, using a raw NVMe device
directly (no intermediary filesystem on the host) and using a non-debug
kernel (default configuration on Debian distributions):

  $ cat test.sh
  #!/bin/bash

  DEV=/dev/sdk
  MNT=/mnt/sdk
  MOUNT_OPTIONS="-o ssd"

  mkfs.btrfs -f -m single -d single $DEV
  mount $MOUNT_OPTIONS $DEV $MNT

  dbench -D $MNT -t 200 40

  umount $MNT

The results before this change:

 Operation      Count    AvgLat    MaxLat
 ----------------------------------------
 NTCreateX    5761605     0.172   312.057
 Close        4232452     0.002    10.927
 Rename        243937     1.406   277.344
 Unlink       1163456     0.631   298.402
 Deltree          160    11.581   221.107
 Mkdir             80     0.003     0.005
 Qpathinfo    5221410     0.065   122.309
 Qfileinfo     915432     0.001     3.333
 Qfsinfo       957555     0.003     3.992
 Sfileinfo     469244     0.023    20.494
 Find         2018865     0.448   123.659
 WriteX       2874851     0.049   118.529
 ReadX        9030579     0.004    21.654
 LockX          18754     0.003     4.423
 UnlockX        18754     0.002     0.331
 Flush         403792    10.944   359.494

Throughput 908.444 MB/sec  40 clients  40 procs  max_latency=359.500 ms

The results after this change:

 Operation      Count    AvgLat    MaxLat
 ----------------------------------------
 NTCreateX    6442521     0.159   230.693
 Close        4732357     0.002    10.972
 Rename        272809     1.293   227.398
 Unlink       1301059     0.563   218.500
 Deltree          160     7.796    54.887
 Mkdir             80     0.008     0.478
 Qpathinfo    5839452     0.047   124.330
 Qfileinfo    1023199     0.001     4.996
 Qfsinfo      1070760     0.003     5.709
 Sfileinfo     524790     0.033    21.765
 Find         2257658     0.314   125.611
 WriteX       3211520     0.040   232.135
 ReadX        10098969     0.004    25.340
 LockX          20974     0.003     1.569
 UnlockX        20974     0.002     3.475
 Flush         451553    10.287   331.037

Throughput 1011.77 MB/sec  40 clients  40 procs  max_latency=331.045 ms

+10.8% throughput, -8.2% max latency
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NFilipe Manana <fdmanana@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

There are only 2 direct calls to set_extent_bit outside of extent-io -
in btrfs_find_new_delalloc_bytes and btrfs_truncate_block, the rest are
thin wrappers around __set_extent_bit. This adds unnecessary indirection
and just makes it more annoying when looking at the various extent bit
manipulation functions.  This patch renames __set_extent_bit to
set_extent_bit effectively removing a level of indirection. No
functional changes.
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
[ reformat and remove __must_check ]
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>

Reviewed-by: NJohannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: NNikolay Borisov <nborisov@suse.com>
Reviewed-by: NDavid Sterba <dsterba@suse.com>
Signed-off-by: NDavid Sterba <dsterba@suse.com>