Currently GC task is started for each f2fs formatted/mounted device.
But, when we check the task list, using 'ps', there is no distinguishing
factor between the tasks. So, name the task as per the block device just
like the flusher threads.
Also, remove the macro GC_THREAD_NAME and instead use the name: f2fs_gc
to avoid name length truncation, as the command length is 16
-> TASK_COMM_LEN 16 and example name like:
f2fs_gc_task:8:16 -> this exceeds name length

Before Patch for 2 F2FS formatted partitions:
root  28061  0.0  0.0  0 0 ? S 10:31   0:00 [f2fs_gc_task]
root  28087  0.0  0.0  0 0 ? S 10:32   0:00 [f2fs_gc_task]

After Patch:
root  16756  0.0  0.0  0  0 ?  S  14:57   0:00 [f2fs_gc-8:18]
root  16765  0.0  0.0  0  0 ?  S  14:57   0:00 [f2fs_gc-8:19]
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

 1. If f2fs is mounted with background_gc_off option, checking
    BG_GC is not redundant.
 2. f2fs_balance_fs is checked in f2fs_gc, so this is also redundant.
Signed-off-by: NChangman Lee <cm224.lee@samsung.com>
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

1. Background

Previously, if f2fs tries to move data blocks of an *evicting* inode during the
cleaning process, it stops the process incompletely and then restarts the whole
process, since it needs a locked inode to grab victim data pages in its address
space. In order to get a locked inode, iget_locked() by f2fs_iget() is normally
used, but, it waits if the inode is on freeing.

So, here is a deadlock scenario.
1. f2fs_evict_inode()       <- inode "A"
  2. f2fs_balance_fs()
    3. f2fs_gc()
      4. gc_data_segment()
        5. f2fs_iget()      <- inode "A" too!

If step #1 and #5 treat a same inode "A", step #5 would fall into deadlock since
the inode "A" is on freeing. In order to resolve this, f2fs_iget_nowait() which
skips __wait_on_freeing_inode() was introduced in step #5, and stops f2fs_gc()
to complete f2fs_evict_inode().

1. f2fs_evict_inode()           <- inode "A"
  2. f2fs_balance_fs()
    3. f2fs_gc()
      4. gc_data_segment()
        5. f2fs_iget_nowait()   <- inode "A", then stop f2fs_gc() w/ -ENOENT

2. Problem and Solution

In the above scenario, however, f2fs cannot finish f2fs_evict_inode() only if:
 o there are not enough free sections, and
 o f2fs_gc() tries to move data blocks of the *evicting* inode repeatedly.

So, the final solution is to use f2fs_iget() and remove f2fs_balance_fs() in
f2fs_evict_inode().
The f2fs_evict_inode() actually truncates all the data and node blocks, which
means that it doesn't produce any dirty node pages accordingly.
So, we don't need to do f2fs_balance_fs() in practical.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

After doing a write_checkpoint from garbage collection path if there is still
need to do more garbage collection, gc_more label is used to jump and start
the process again. And in that process, first step before getting victim is to
check if there are not enough free sections, which is already done before
doing a jump to gc_more. We can avoid the redundant call to check free
sections, by checking the gc_type flag which will remain FG_GC(value 1) under
this condition.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

This patch supports ioctl FIFREEZE and FITHAW to snapshot filesystem.
Before calling f2fs_freeze, all writers would be suspended and sync_fs
would be completed. So no f2fs has to do something.
Just background gc operation should be skipped due to generate dirty
nodes and data until unfreeze.
Signed-off-by: NChangman Lee <cm224.lee@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

The caller of start_bidx_of_node() should give proper node offsets which
point only direct node blocks. Otherwise, it is a caller's bug.
This patch adds comments to make it clear.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

Add __init to functions in init_f2fs_fs for code consistency.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

I'd like to revisit the f2fs_gc flow and rewrite as follows.

1. In practical, the nGC parameter of f2fs_gc is meaningless. So, let's
  remove it.
2. Background GC marks victim blocks as dirty one at a time.
3. Foreground GC should do cleaning job until acquiring enough free
  sections. Afterwards, it needs to do checkpoint.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

This patch cleans up a couple of unnecessary codes related to unused variables
and return values.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

This patch also resolves the following warning reported by kbuild test robot.

fs/f2fs/gc.c: In function 'start_bidx_of_node':
fs/f2fs/gc.c:453:21: warning: 'bidx' may be used uninitialized in this function
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

No need to initialize  "struct f2fs_gc_kthread *gc_th = NULL",
as gc_th = NULL, will be taken care by the return values of kmalloc().
And fix codes in other places.
Signed-off-by: NNamjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: NAmit Sahrawat <a.sahrawat@samsung.com>

As pointed out by Randy Dunlap, this patch removes all usage of "/**" for comment
blocks. Instead, just use "/*".
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>

This adds on-demand and background cleaning functions.

- The basic background cleaning policy is trying to do cleaning jobs as much as
  possible whenever the system is idle. Once the background cleaning is done,
  the cleaner sleeps an amount of time not to interfere with VFS calls. The time
  is dynamically adjusted according to the status of whole segments, which is
  decreased when the following conditions are satisfied.

  . GC is not conducted currently, and
  . IO subsystem is idle by checking the number of requets in bdev's request
     list, and
  . There are enough dirty segments.

  Otherwise, the time is increased incrementally until to the maximum time.
  Note that, min and max times are 10 secs and 30 secs by default.

- F2FS adopts a default victim selection policy where background cleaning uses
  a cost-benefit algorithm, while on-demand cleaning uses a greedy algorithm.

- The method of moving data during the cleaning is slightly different between
  background and on-demand cleaning schemes. In the case of background cleaning,
  F2FS loads the data, and marks them as dirty. Then, F2FS expects that the data
  will be moved by flusher or VM. In the case of on-demand cleaning, F2FS should
  move the data right away.

- In order to identify valid blocks in a victim segment, F2FS scans the bitmap
  of the segment managed as an SIT entry.
Signed-off-by: NJaegeuk Kim <jaegeuk.kim@samsung.com>