Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add platform data and set usb3_lpm_capable and has_lpm_erratum.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the alignment of the PCI device definitions. Also change the hex
digit capitalization of one constant to make it consistent with the
rest of the file and driver.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.

The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.

Add checking for the new ID to pass driver probe.

Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.

Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We *know* our threads executes with our IRQs
disabled. We really don't need to use the _irqsave()
variant of spin_lock().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of limiting __dwc3_gadget_kick_transfer() to
Xfer Complete, we can try to issue Update Transfer
command from Xfer In Progress too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we get a Xfer Not Ready event with reason
"Transfer Active" it means endpoint is still
transferring data and we can use that to issue
update transfer for this particular endpoint
in case we have pending requests in our queue.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if by the time we get to XFER_COMPLETE we have
pending requests to be processed, instead of waiting
for a following XFER_NOT_READY, let's start the request
right away and, maybe, save the time of a few NAKs
due to lack of started transfers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Sharing the ACPI companion with dwc3 core so it has access
to the properties defined for DWC3 in ACPI tables.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional affect on existing platforms, but the driver
is now ready to extract the properties also from ACPI tables
as well as from DT.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

of_usb_get_dr_mode will be converted into more generic
usb_get_dr_mode function that will take struct device
instead of struct device_node as its parameter.

To make the conversion possible later, waiting for the
platform device for dwc3 to be populated before calling
of_usb_get_dr_mode.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for USB DRVVBUS pinctrl state change during
suspend/resume. This helps is conserving power during
system sleep.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: NNikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We shouldn't return -EBUSY, that's used only internally
when the core still has transfers in flight on a given
endpoint.

Also, combine the error reporting so that we don't have
to duplicate it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of clearing DWC3_PENDING_REQUEST when
we start transfer, let's do it when the request
is actually queued, that way we know for sure
that we're clearing in the right time.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In an attempt to make dwc3 slightly faster, let's
start usb_requests as soon as they come as that will
let us avoid a XFER_NOT_READY event and save a little
bit of time.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

by moving trace_dwc3_ep_queue() from dwc3_gadget_ep_queue()
to __dwc3_gadget_ep_queue() after usb_request is properly
initialized, makes for a better output always showing a
request with 0 actual and -115 (-EINPROGRESS) status.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using spin_lock() in hard irq handler is pointless
and causes a BUG() in RT (real-time) configuration
so get rid of it.

The reason it's pointless is because the driver is
basically accessing register which is, anyways,
atomic.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we enable IRQs before requesting our
extcon device, we might fall into a situation
where and IRQ fires before we're ready to
handle it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Convert endpoint configuration to new capabilities model.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in  dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.

Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.

Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We should only change endpoint names when we
actually manage to enable/disable it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.

Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.

Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

now that we have no users of dev_dbg() in dwc3,
we can safely remove CONFIG_USB_DWC3_DEBUG.

If dev_dbg() is ever strictly necessary - and I
don't see why it would, considering we want to
rely on tracepoints for debug - we will depend
on DYNAMIC_PRINTK to enable such messages.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the mode of operation is exposed through debugfs
at all times. Because of that, we're removing
the unnecessary messages.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

those two messages are informing that the clock
doesn't exist; that, however, is a valid situation
and driver continues just fine by ignoring the error.
Reviewed-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that's an error condition, not a debugging message.

Let's promote it appropriately.
Signed-off-by: NFelipe Balbi <balbi@ti.com>