This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.

This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Use the recently-added bio front_pad field to allocate struct dm_target_io.

Prior to this patch, dm_target_io was allocated from a mempool. For each
dm_target_io, there is exactly one bio allocated from a bioset.

This patch merges these two allocations into one allocation: we create a
bioset with front_pad equal to the size of dm_target_io so that every
bio allocated from the bioset has sizeof(struct dm_target_io) bytes
before it. We allocate a bio and use the bytes before the bio as
dm_target_io.

_tio_cache is removed and the tio_pool mempool is now only used for
request-based devices.

This idea was introduced by Kent Overstreet.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: tj@kernel.org
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The bio prison code will be useful to other future DM targets so
move it to a separate module.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The bio prison code will be useful to share with future DM targets.

Prepare to move this code into a separate module, adding a dm prefix
to structures and functions that will be exported.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Support discards when the pool's block size is not a power of 2.
The block layer assumes discard_granularity is a power of 2 (in
blkdev_issue_discard), so we set this to the largest power of 2 that is
a divides into the number of sectors in each block, but never less than
DATA_DEV_BLOCK_SIZE_MIN_SECTORS.

This patch eliminates the "Discard support must be disabled when the
block size is not a power of 2" constraint that was imposed in commit
55f2b8bd ("dm thin: support for non power of 2 pool blocksize").  That
commit was incomplete: using a block size that is not a power of 2
shouldn't mean disabling discard support on the device completely.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The device had an undocumented "feature": it can provide a sequence of
spurious link-down status data even if the link is up all the time.
A sequence of 10 was seen so update the link state only after the device
reports the same link state 20 times.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Reported-by: NMichael Leun <lkml20120218@newton.leun.net>
Tested-by: NMichael Leun <lkml20120218@newton.leun.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use the ACCESS_ONCE macro in dm-bufio and dm-verity where a variable
can be modified asynchronously (through sysfs) and we want to prevent
compiler optimizations that assume that the variable hasn't changed.
(See Documentation/atomic_ops.txt.)
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use list_move() instead of list_del() + list_add().

spatch with a semantic match was used to find this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().

spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The commit 254d1a3f, titled
"xen/pv-on-hvm kexec: shutdown watches from old kernel" assumes that the
XenBus backend can deal with reading of values from:
 "control/platform-feature-xs_reset_watches":

    ... a patch for xenstored is required so that it
    accepts the XS_RESET_WATCHES request from a client (see changeset
    23839:42a45baf037d in xen-unstable.hg). Without the patch for xenstored
    the registration of watches will fail and some features of a PVonHVM
    guest are not available. The guest is still able to boot, but repeated
    kexec boots will fail."

Sadly this is not true when using a Xen 3.4 hypervisor and booting a PVHVM
guest. We end up hanging at:

  err = xenbus_scanf(XBT_NIL, "control",
                        "platform-feature-xs_reset_watches", "%d", &supported);

This can easily be seen with guests hanging at xenbus_init:

NX (Execute Disable) protection: active
SMBIOS 2.4 present.
DMI: Xen HVM domU, BIOS 3.4.0 05/13/2011
Hypervisor detected: Xen HVM
Xen version 3.4.
Xen Platform PCI: I/O protocol version 1
... snip ..
calling  xenbus_init+0x0/0x27e @ 1

Reverting the commit or using the attached patch fixes the issue. This fix
checks whether the hypervisor is older than 4.0 and if so does not try to
perform the read.

Fixes-Oracle-Bug: 14708233
CC: stable@vger.kernel.org
Acked-by: NOlaf Hering <olaf@aepfle.de>
[v2: Added a comment in the source code]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

It is possible to miss data when using the kdb pager.  The kdb pager
does not pay attention to the maximum column constraint of the screen
or serial terminal.  This result is not incrementing the shown lines
correctly and the pager will print more lines that fit on the screen.
Obviously that is less than useful when using a VGA console where you
cannot scroll back.

The pager will now look at the kdb_buffer string to see how many
characters are printed.  It might not be perfect considering you can
output ASCII that might move the cursor position, but it is a
substantially better approximation for viewing dmesg and trace logs.

This also means that the vt screen needs to set the kdb COLUMNS
variable.

Cc: <stable@vger.kernel.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

It is a common enough mistake for people to specify "kdb" when they
meant to type "kbd" that the kgdboc can just accept both since they
both mean the same thing anyway.  Specifically it is for the case
where you want kdb to be active on your graphics console + keyboard
(where kbd was the original abbreviation for keyboard).

With this change kgdboc will now accept either to mean the same thing:
   kgdboc=kbd
   kgdboc=kdb
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

The following error appeared due to a merge problem; the patches:

fc108d24 "mmc: mxs-mmc: fix deadlock caused by recursion loop"
829c1bf4 "mmc: spi: Pull out parts shared between MMC and SPI"

came in through separate branches and cause this build error when
combined.

drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_enable_sdio_irq':
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'base'
drivers/mmc/host/mxs-mmc.c:527:3: error: 'struct mxs_mmc_host' has no member named 'devid'
make[3]: *** [drivers/mmc/host/mxs-mmc.o] Error 1

This patch corrects the issue.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This USB V.92/V.32bis Controllered Modem have the USB vendor ID 0x0572
and device ID 0x1340. It need the NO_UNION_NORMAL quirk to be recognized.

Reference:
http://www.conexant.com/servlets/DownloadServlet/DSH-201723-005.pdf?docid=1725&revid=5
See idVendor and idProduct in table 6-1. Device Descriptors
Signed-off-by: NJean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).

http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.

Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: NKevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We nowdays copy the buffer and free fw->data, so make the debug printk use
the right thing.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.

Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled.  Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.

Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.

To avoid possible Tx stalls, change WTHRESH back to 1.

The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.

please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3b
Author: Tom Herbert <therbert@google.com>
Date:   Mon Nov 28 16:33:16 2011 +0000

    e1000e: Support for byte queue limits

    Changes to e1000e to use byte queue limits.
Reported-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Tested-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An SKB paged fragment can consist of a compound page with order > 0.
However the netchannel protocol deals only in PAGE_SIZE frames.

Handle this in netbk_gop_frag_copy and xen_netbk_count_skb_slots by
iterating over the frames which make up the page.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"protos" is an array of unsigned longs and "i" is the number of bits in
an unsigned long so we need to use 1UL as well to prevent the shift
from wrapping around.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If vxlan is created and the ifindex is passed; there are two cases which
are incorrectly handled by the existing code. The ifindex could be zero
(i.e. no device) or there could be no device with that ifindex.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vxlan was trying to use postpull_rcsum to allow receive checksum
offload to work on drivers using CHECKSUM_COMPLETE method. But this
doesn't work correctly. Just force full receive checksum on received
packet.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tell upper layer protocols to allocate skb with additional headroom.
This avoids allocation and copy in local packet sends.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN bases source UDP port based on flow to help the
receiver to be able to load balance based on outer header flow.

This patch restricts the port range to the normal UDP local
ports, and allows overriding via configuration.

It also uses jhash of Ethernet header when looking at flows
with out know L3 header.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When tunnelling a skb, associate it with the tunnel socket.
This allows parameters set on tunnel socket (like multicast loop
flag), to be picked up by ip_output.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Select source address for VXLAN packet based on route destination
and don't lie to route code. VXLAN is not GRE.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shift was wrong direction causing packets to hash based on
other parts of the ethernet header, not the address.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move code to find destination to a small function.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch "drivers/video/gbefb.c: use devm_ functions" caused a
compile error.

drivers/video/gbefb.c:1159:16: error: implicit declaration of function
'devm_ioremap' [-Werror=implicit-function-declaration]
drivers/video/gbefb.c:1179:3: error: implicit declaration of function
'devm_ioremap_nocache' [-Werror=implicit-function-declaration]

Fix it by including linux/io.h which defines those functions.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Damien Cassou <damien.cassou@lifl.fr>

Commit 6b8029fa ("rtc: kconfig: remove unnecessary dependencies")
removed various 'depends on RTC_CLASS' dependencies but also removed a
few 'default RTC_CLASS' statements, which actually changed default
behavior.

This resulted in the various RTC interfaces (sysfs, proc, dev) all being
disabled by default, even when RTC_CLASS is enabled:

   # CONFIG_RTC_INTF_SYSFS is not set
   # CONFIG_RTC_INTF_PROC is not set
   # CONFIG_RTC_INTF_DEV is not set

which is different from previous behavior (all of these where enabled.)

To fix, add back the 'default RTC_CLASS' statments to each of the
RTC_INTF_* options.

I noticed this because some RTC tests started failing on my TI OMAP
platforms because /dev/rtc0 was not present anymore, even though the
driver was present and RTC_CLASS was enabled.
Signed-off-by: NKevin Hilman <khilman@ti.com>
Acked-by: NVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Address comments provided by Andrew Morton:
https://lkml.org/lkml/2012/10/3/550

 - Keeps consistent kerneldoc compatible comments style for new static
   functions.
 - Removes unnecessary complexity from destination ID allocation
   routine.
 - Uses kcalloc() for code clarity.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update discovery process initialization based on Andrew Morton's comments:
https://lkml.org/lkml/2012/10/3/552.

This update processes all enumerating mports first and schedules discovery
work after that. If the initialization routine fails to allocate resources
needed to execute discovery, it abandons discovery for all ports.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use msleep() for code clarity as suggested by Andrew Morton in his
comments for the original patch: https://lkml.org/lkml/2012/10/3/546.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

tpm_write calls tpm_transmit without checking the return value and
assigns the return value unconditionally to chip->pending_data, even if
it's an error value.
This causes three bugs.

So if we write to /dev/tpm0 with a tpm_param_size bigger than
TPM_BUFSIZE=0x1000 (e.g. 0x100a)
and a bufsize also bigger than TPM_BUFSIZE (e.g. 0x100a)
tpm_transmit returns -E2BIG which is assigned to chip->pending_data as
-7, but tpm_write returns that TPM_BUFSIZE bytes have been successfully
been written to the TPM, altough this is not true (bug #1).

As we did write more than than TPM_BUFSIZE bytes but tpm_write reports
that only TPM_BUFSIZE bytes have been written the vfs tries to write
the remaining bytes (in this case 10 bytes) to the tpm device driver via
tpm_write which then blocks at

 /* cannot perform a write until the read has cleared
 either via tpm_read or a user_read_timer timeout */
 while (atomic_read(&chip->data_pending) != 0)
	 msleep(TPM_TIMEOUT);

for 60 seconds, since data_pending is -7 and nobody is able to
read it (since tpm_read luckily checks if data_pending is greater than
0) (#bug 2).

After that the remaining bytes are written to the TPM which are
interpreted by the tpm as a normal command. (bug #3)
So if the last bytes of the command stream happen to be a e.g.
tpm_force_clear this gets accidentally sent to the TPM.

This patch fixes all three bugs, by propagating the error code of
tpm_write and returning -E2BIG if the input buffer is too big,
since the response from the tpm for a truncated value is bogus anyway.
Moreover it returns -EBUSY to userspace if there is a response ready to be
read.
Signed-off-by: NPeter Huewe <peter.huewe@infineon.com>
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>

The virq_disabled flag tracks the userspace view of INTx masking
across interrupt mode changes, but we're not consistently applying
this to the interrupt and masking handler notion of the device.
Currently if the user sets DisINTx while in MSI or MSIX mode, then
returns to INTx mode (ex. rebooting a qemu guest), the hardware has
DisINTx+, but the management of INTx thinks it's enabled, making it
impossible to actually clear DisINTx.  Fix this by updating the
handler state when INTx is re-enabled.

Cc: stable@vger.kernel.org
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>

We need to be ready to recieve an interrupt as soon as we call
request_irq, so our eventfd context setting needs to be moved
earlier.  Without this, an interrupt from our device or one
sharing the interrupt line can pass a NULL into eventfd_signal
and oops.

Cc: stable@vger.kernel.org
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>

Our mmap path mistakely relied on vma->vm_pgoff to get set in
remap_pfn_range.  After b3b9c293, that path only applies to
copy-on-write mappings.  Set it in our own code.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>

This patch try to fix the S3 regression https://lkml.org/lkml/2012/10/5/433,
which includes below line:
[ 1554.684638] sysfs: cannot create duplicate filename '/devices/pnp0/00:0c/ppi'

The root cause is that ppi sysfs teardown code is MIA, so while S3 resume,
the ppi kobject will be created again upon existing one.

To make the tear down code simple, change the ppi subfolder creation from
using kobject_create_and_add to just using a named ppi attribute_group. Then
ppi sysfs teardown could be done with a simple sysfs_remove_group call.

Adjusted the name & return type for ppi sysfs init function.
Reported-by: NBen Guthro <ben@guthro.net>
Signed-off-by: NGang Wei <gang.wei@intel.com>
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>

These drivers use no sleep or delay functions so they don't need to
include <linux/delay.h>.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Rudolf Marek <r.marek@assembler.cz>