Subclassing the generic USB device driver to override the
default configuration selection regardless of matching interface
drivers.

The r815x family devices expose a vendor specific function which
the r8152 interface driver wants to handle.  This is the preferred
device mode. Additionally one or more USB class functions are
usually supported for hosts lacking a vendor specific driver. The
choice is USB configuration based, with one alternate function per
configuration.

Example device with both NCM and ECM alternate cfgs:

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  3
P:  Vendor=0bda ProdID=8156 Rev=31.00
S:  Manufacturer=Realtek
S:  Product=USB 10/100/1G/2.5G LAN
S:  SerialNumber=001000001
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=256mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=83(I) Atr=03(Int.) MxPS=   2 Ivl=128ms
C:  #Ifs= 2 Cfg#= 2 Atr=a0 MxPwr=256mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=128ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
C:  #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr=256mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=
E:  Ad=83(I) Atr=03(Int.) MxPS=  16 Ivl=128ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms

A problem with this is that Linux will prefer class functions over
vendor specific functions. Using the above example, Linux defaults
to cfg #2, running the device in a sub-optimal NCM mode.

Previously we've attempted to work around the problem by
blacklisting the devices in the ECM class driver "cdc_ether", and
matching on the ECM class function in the vendor specific interface
driver. The latter has been used to switch back to the vendor
specific configuration when the driver is probed for a class
function.

This workaround has several issues;
- class driver blacklists is additional maintanence cruft in an
  unrelated driver
- class driver blacklists prevents users from optionally running
  the devices in class mode
- each device needs double match entries in the vendor driver
- the initial probing as a class function slows down device
  discovery

Now these issues have become even worse with the introduction of
firmware supporting both NCM and ECM, where NCM ends up as the
default mode in Linux. To use the same workaround, we now have
to blacklist the devices in to two different class drivers and
add yet another match entry to the vendor specific driver.

This patch implements an alternative workaround strategy -
independent of the interface drivers.  It avoids adding a
blacklist to the cdc_ncm driver and will let us remove the
existing blacklist from the cdc_ether driver.

As an additional bonus, removing the blacklists allow users to
select one of the other device modes if wanted.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My system shows almost 10 million of these messages over a 24-hour
period which pollutes my logs.
Signed-off-by: NAndrew Gaul <gaul@google.com>
Link: https://lore.kernel.org/r/20221002034128.2026653-1-gaul@google.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The Lenovo USB-C Travel Hub supports MAC passthrough.
Signed-off-by: NAndré Apitzsch <git@apitzsch.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rtl8152 driver does not disable multicasting when userspace asks
it to. For example:
 $ ifconfig eth0 -multicast -allmulti
 $ tcpdump -p -i eth0  # will still capture multicast frames

Fix by clearing the device multicast filter table when multicast and
allmulti are both unset.

Tested as follows:
- Set multicast on eth0 network interface
- verify that multicast packets are coming in:
  $ tcpdump -p -i eth0
- Clear multicast and allmulti on eth0 network interface
- verify that no more multicast packets are coming in:
  $ tcpdump -p -i eth0
Signed-off-by: NSven van Ashbrook <svenva@chromium.org>
Acked-by: NHayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220830045923.net-next.v1.1.I4fee0ac057083d4f848caf0fa3a9fd466fc374a0@changeidSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220830201457.7984-1-wsa+renesas@sang-engineering.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.

Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.

Tested on a ThinkPad 13 1st gen with the expected results:

passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled:  Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: NJean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.

Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.

Tested on a ThinkPad 13 1st gen with the expected results:

passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled:  Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: NJean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX FIFO would be changed when suspending, so the related settings
have to be modified, too. Otherwise, the flow control would work
abnormally.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216333Reported-by: NMark Blakeney <mark.blakeney@bullet-systems.net>
Fixes: cdf0b86b ("r8152: fix a WOL issue")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The units of PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY are 16 bytes.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes that the platform is waked by an unexpected packet. The
size and range of FIFO is different when the device enters S3 state,
so it is necessary to correct some settings when suspending.

Regardless of jumbo frame, set RMS to 1522 and MTPS to MTPS_DEFAULT.
Besides, enable MCU_BORW_EN to update the method of calculating the
pointer of data. Then, the hardware could get the correct data.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220718082120.10957-391-nic_swsd@realtek.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

A warning is triggered by commit 66e4c8d9 ("net: warn if transport
header was not set"). The warning is harmless, because the value from
skb_transport_offset() is only used for skb_is_gso() is true or the
skb->ip_summed is equal to CHECKSUM_PARTIAL.

Fixes: 66e4c8d9 ("net: warn if transport header was not set")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lenovo Thunderbolt 4 Dock, and other Lenovo USB Docks are using the
original Realtek USB ethernet Vendor and Product IDs
If the Network device is Realtek verify that it is on a Lenovo USB hub
before enabling the passthru feature

This also adds in the device IDs for the Lenovo USB Dongle and one other
USB-C dock

V2 fix formating of code
V3 remove Generic define for Device ID 0x8153 and change it to use value
V4 rearrange defines and case statement to put them in better order
v5 create helper function to do the testing work as suggested
Signed-off-by: NDavid Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20220517180539.25839-1-dober6023@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

r8152 uses a custom napi weight, switch to the new
API for setting custom weight.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f77b83b5.

This change breaks multiple usb to ethernet dongles attached on Lenovo
USB hub.

Fixes: f77b83b5 ("net: usb: r8152: Add MAC passthrough support for more Lenovo Docks")
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Link: https://lore.kernel.org/r/20220105155102.8557-1-aaron.ma@canonical.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.

Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.

Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert usb drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, dev->addr_len)
  + eth_hw_addr_set(dev, np)

Manually checked these are either usbnet or pure etherdevs.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the situation that the disconnect event comes very late when the
device is unplugged, the driver would resubmit the RX bulk transfer
after getting the callback with -EPROTO immediately and continually.
Finally, soft lockup occurs.

This patch avoids to resubmit RX immediately. It uses a workqueue to
schedule the RX NAPI. And the NAPI would resubmit the RX. It let the
disconnect event have opportunity to stop the submission before soft
lockup.
Reported-by: NJason-ch Chen <jason-ch.chen@mediatek.com>
Tested-by: NJason-ch Chen <jason-ch.chen@mediatek.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Convert net/usb from ether_addr_copy() to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - ether_addr_copy(dev->dev_addr, np)
  + eth_hw_addr_set(dev, np)
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().

Fixes: 9370f2d0 ("support request_firmware for RTL8153")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.

Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.

This is a purely cosmetic change intended to help readers find
their way through the implementation.

Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJason Gunthorpe <jgg@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

r8152 driver sets up the MAC address at reset-resume, while
rtl8152_set_mac_address() has the temporary autopm get/put.  This may
lead to a deadlock as the PM lock has been already taken for the
execution of the runtime PM callback.

This patch adds the workaround to avoid the superfluous autpm when
called from rtl8152_reset_resume().

Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits.  This may lead to
the imbalance of PM refcount.  This patch addresses it.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the information of the pipes to avoid calling usb_rcvctrlpipe(),
usb_sndctrlpipe(), usb_rcvbulkpipe(), usb_sndbulkpipe(), and
usb_rcvintpipe() frequently.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

wierdness  ==> weirdness
multicat  ==> multicast
limite  ==> limit
adddress  ==> address
operater  ==> operator
intial  ==> initial
smaler  ==> smaller
Communcation  ==> Communication
funcitons  ==> functions
everytime  ==> every time
Neigbor  ==> Neighbor
performace  ==> performance
Signed-off-by: NZheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Verify some fields of the USB descriptor to make sure the driver
could be used by the device.

Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.

BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943 ("r8152: search the configuration of vendor mode")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove DELL_TB_RX_AGG_BUG and LENOVO_MACPASSTHRU flags of rtl8152_flags.
They are only set when initializing and wouldn't be change. It is enough
to record them with variables.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redefine REALTEK_USB_DEVICE macro with USB_DEVICE_INTERFACE_CLASS and
USB_DEVICE_AND_INTERFACE_INFO to simply the code.

Although checkpatch.pl shows the following error, it is more readable.

	ERROR: Macros with complex values should be enclosed in parentheses
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RTL8156 support CDC NCM mode. And users could set the configuration
of the USB device between vendor and NCM mode dynamically by themselves.
That is, the driver doesn't need to set vendor mode from NCM mode.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the timeout occurs, we still have to run the following process
for releasing patch request. Otherwise, the PHY would keep no link.
Therefore, use break to stop the loop of loading firmware and
release the patch request rather than return the function directly.

Fixes: 4a51b0e8 ("r8152: support PHY firmware for RTL8156 series")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vendor mode is not always at config #1, so it is necessary to
set the correct configuration number.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support new firmware type and method for RTL8156 series.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>