- 21 5月, 2010 12 次提交
-
-
由 Johan Hovold 提交于
Make sure fifo is emptied on close. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
On errors the fifo was reset without any locking. This could race with write which do kfifo_put and perhaps also chars_in_buffer and write_room. Every other access to the fifo is protected using the port lock so better add it to the error path as well. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Make sure chars_in_buffer accounts also for data in host stack queues. This fixes the problem with tty_wait_until_sent returning too soon at close which could cause the final write urb to be cancelled. Reported-by: NPete Zaitcev <zaitcev@redhat.com> Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
The pl2303 requires a bulk-in buffer larger than endpoint size to keep up at high baudrates without loosing data. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Increase the bulk-out buffer size from 64 to 256 byte. This gives a significant increase in throughput already at 1Mbaud as well as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud (128b would not suffice). 64b 256b 921k: 640 KB/s 870 KB/s 3M: 640 KB/s 2520 KB/s Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
The cp210x requires a bulk-in buffer larger than endpoint size to keep up at high baudrates without loosing data. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Increase the bulk-out buffer size from 64 to 256 byte. This gives a significant increase in throughput already at 1Mbaud (e.g. 710 instead of 640 KB/s) as well as lowered CPU usage. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Allow drivers to define custom bulk in/out buffer sizes in struct usb_serial_driver. If not set, fall back to the default buffer size which matches the endpoint size. Three drivers are currently freeing the pre-allocated buffers and allocating larger ones to achieve this at port probe (ftdi_sio) or even at port open (ipaq and iuu_phoenix), which needless to say is suboptimal. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Randy Dunlap 提交于
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled: drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq' Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Vijay Kumar 提交于
Add ZIO Motherboard USB serial interface driver. Signed-off-by: NVijay Kumar B. <vijaykumar@zilogic.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jason Wessel 提交于
The usb console code has had a long standing problem of not being able to pass the baud rate from the kernel argument console=ttyUSB0,BAUD down to the initial tty open, unless you were willing to settle for 9600 baud. The solution is to directly use tty_init_termios() in usb_console_setup() as this will preserve any changes to the initial termios setting on future opens. CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: NJason Wessel <jason.wessel@windriver.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jason Wessel 提交于
Replace all instances of using the console variable in struct usb_serial_port with the struct tty_port version. CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oliver@neukum.org> CC: Andrew Morton <akpm@linux-foundation.org> CC: linux-usb@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by: NJason Wessel <jason.wessel@windriver.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 01 5月, 2010 5 次提交
-
-
由 Randy Dunlap 提交于
Fix printk format warning in usbserial/ti_usb: drivers/usb/serial/ti_usb_3410_5052.c:1738: warning: format '%d' expects type 'int', but argument 5 has type 'size_t' Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Greg Kroah-Hartman 提交于
This adds a device id for a Cinterion device. Reported-by: NJohn Race <John.Race@roscom.co.uk> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Mahesh Kuruganti 提交于
PATCH TO EXTEND SUPPORT TO AC8710 WITH 0xFFFF Product ID. Signed-off-by: NMahesh Kuruganti <maheshkuruganti@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Simone Contini 提交于
I tried a magnetic stripe reader (http://www.kimaldi.com/kimaldi_eng/productos/lectores_de_tarjetas/lectores_tarjeta_chip_y_dni/lector_hibrido_uniform_hcr_331) and I see that it is interfaced with a PL2303. I wrote a patch to use your driver which simply adds the product ID for the device and it seems working fine. From: Simone Contini <s.contini@oltrelinux.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Dominik Brodowski 提交于
Based on the information provided for by Paweł Drobek, add a second vendor ID and the correct product ID for ZTE MF 330. Reported-by: NPaweł Drobek <pawel.drobek@gmail.com> Signed-off: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 23 4月, 2010 4 次提交
-
-
由 Manuel Jander 提交于
I read a rumor that the AdLink ND6530 USB RS232, RS422 and RS485 isolated adapter is actually a PL2303 based usb serial adapter. I tried it out, and as far as I can tell it works. Signed-off-by: NManuel Jander <manuel.jander@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 William Lightning 提交于
Signed-off-by: NWilliam Lightning <kassah@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Dan Williams 提交于
These phones also have the familiar ttyACM0/ttyUSB0 schizophrenia when placed into "Dial-up Networking" mode after connecting a USB cable. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alex Manoussakis 提交于
The following patch adds support for Multitech Systems' MT9234MU and MT9234ZBA usb dialup fax modems. It is based on a patch and firmware provided to me by Multitech Systems' support, after I reported to them that my MT9234MU modem was not working with recent linux kernels. Signed-off-by: NAlex Manoussakis <alex@juniper.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 19 3月, 2010 14 次提交
-
-
由 Michael Brunner 提交于
This patch removes a double usb_control_msg that sets the cp210x configuration registers a second time when calling cp210x_set_config. For data sizes >2 the second write gets corrupted. The patch has been created against 2.6.34-rc1, but all cp210x driver revisions are affected. Signed-off-by: NMichael Brunner <mibru@gmx.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alessio Igor Bogani 提交于
The change_speed() function should be serialized against multiple calls. Use the cfg_lock mutex to do this. Signed-off-by: NAlessio Igor Bogani <abogani@texware.it> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 spark 提交于
Signed-off-by: Nspark <spark@bandrich.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Stefan Schmidt 提交于
The module is called qcaux and not moto_modem. Also use help instead of ---help-- to be in sync with the other Kconfig entries. Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Nathaniel McCallum 提交于
Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Nathaniel McCallum 提交于
Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Nathaniel McCallum 提交于
Signed-off-by: NNathaniel McCallum <nathaniel@natemccallum.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Daniel Sangorrin 提交于
This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds identifiers for CONTEC USB serial converter. I tested it with the device COM-1(USB)H [akpm@linux-foundation.org: keep the VIDs sorted a bit] Signed-off-by: NDaniel Sangorrin <daniel.sangorrin@gmail.com> Cc: Andreas Mohr <andi@lisas.de> Cc: Radek Liboska <liboska@uochb.cas.cz> Cc: stable <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Bernhard Rosenkraenzer 提交于
This patch adds various USB device IDs for Gobi 2000 devices, as found in the drivers available at https://www.codeaurora.org/wiki/GOBI_ReleasesSigned-off-by: NBernhard Rosenkraenzer <bero@arklinux.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Huang Ying 提交于
I found a DLink DWM 652 U5 USB 3G modem has product ID 0xce1e instead of orignal 0xce16. The new ID is added. And I found there are two entries for 0xce16, one has raw number, the other has symbol DLINK_PRODUCT_DWM_652_U5. This is fixed too. Signed-off-by: NHuang Ying <ying.huang@intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
It is possible to have a multi-port device with a port lacking an in or out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not sufficient to determine whether a specific port has an in or out bulk endpoint. This fixes potential null pointer dereferences in the generic open and write routines, as well as access to uninitialised fifo in write_room and chars_in_buffer. Also let write fail with ENODEV (instead of 0) on missing out endpoint (also on zero-length writes). Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Make sure usb_serial_port_softint is called on errors also when using multi urb writes. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Resubmitting read urb fails with -EPERM if completion handler runs while urb is being killed on close. This should not be reported as an error. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Jason Wessel 提交于
Commit e1108a63 ("usb_serial: Use the shutdown() operation") breaks the ability to use a usb console starting in 2.6.33. This was observed when using console=ttyUSB0,115200 as a boot argument with an FTDI device. The error is: ftdi_sio ttyUSB0: ftdi_submit_read_urb - failed submitting read urb, error -22 The handling of the ASYNCB_INITIALIZED changed in 2.6.32 such that in tty_port_shutdown() it always clears the flag if it is set. The fix is to add a variable to the tty_port struct to indicate when the tty port is a console. CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oliver@neukum.org> CC: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NJason Wessel <jason.wessel@windriver.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 03 3月, 2010 4 次提交
-
-
由 Johan Hovold 提交于
URBs are initialised at probe and do not change. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
No need to check ASYNCB_INITIALIZED anymore as commit e1108a63 (usb_serial: Use the shutdown() operation) make sure that there is no longer any call to unthrottle after device specific close (in which the read urb is killed). Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Remove counter that is never exported. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Dan Williams 提交于
qcaux: add driver for QCDM-capable ports on various devices Many Qualcomm-based devices provide a CDC-ACM port which accepts normal AT commands and PPP connections. But they only provide one which makes status or signal strength requests impossible while PPP is active. They also provide secondary USB interfaces that talk the Qualcomm Diagnostic Monitor (QCDM) protocol which can be used for status and strength. Make those QCDM ports accessible. Signed-off-by: NDan Williams <dcbw@redhat.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-