[Why]
Moving PSR from DMCU to DMCUB.

[How]
Cleanup psr spec files and add PSR hw programming files.
No functionality is included in this change.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.

[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: NNoah Abradjian <noah.abradjian@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Moving PSR from DMCU to DMCUB.

[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.

[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: NNoah Abradjian <noah.abradjian@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add more fields to support upcoming dml versions
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds

[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: NJoseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Test pattern should be applied to hardware when exiting set test pattern
function.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NNikola Cornij <Nikola.Cornij@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI

[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
If dummy pstate latency is 0 we should report the actual
pstate support, and not that pstate is always supported.

[How]
Don't always program pstate support true
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Make sure that lttpr_caps has the mode set to repeater.
Signed-off-by: Nabdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.

[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: NNoah Abradjian <noah.abradjian@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We need to ensure that the DMUIF in MMHUBBUB is also in reset so we
aren't generating requests while the DMCUB is in reset.

[How]
Set DMUIF_SOFT_RESET=1 on reset and DMUIF_SOFT_RESET=0 on reset
release.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The inst firmware isn't necessarily fully flushed to framebuffer
memory and the DMCUB can hang due to invalid inst being parsed.

[How]
Like the fix to flush ringbuffer commands before updating the inbox
write pointer we need to read back inst memory before writing the
CW0 registers.

Add a helper to read 64-byte chunks to avoid a large temporary buffer.
Read the remaining leftover bytes if the inst_fb isn't fully aligned.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There's a data race that can occur between when we update the
inbox write pointer vs when the memory for the command actually gets
flushed from the map to the framebuffer.

DMCUB can read stale or partially invalid data when this race occurs.

[How]
Before updating the write pointer we can read back all pending commands
to ensure that we stall for the writes to be flushed to framebuffer.

We don't need to worry about choosing HDP vs VM flush with this
mechanism.

Drop the dmub_srv_cmd_submit() while we're updating this to work
correctly since nothing was actually using this API and the caller
should be explicit about the API flow here - by doing this on execute
we can give some extra time for the flush to finish while
preparing other commands.

We should try to avoid writing single commands
because of this overhead.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
While doing seamless boot I made some changes
to dcn2 hubbub functions, missed a link

[how]
link hubbub1 func to hubbub2 usage. It has already
been successfully linked in dcn1 and 3.
Signed-off-by: NMartin Leung <martin.leung@amd.com>
Reviewed-by: NAlvin Lee <Alvin.Lee2@amd.com>
Acked-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.

[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NJoshua Aberback <Joshua.Aberback@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Needed to reprogram vblank_start in dml properly in order to get the
correct dlg params to program VTG.
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Previous implementation we may have residual chroma address offset
if transition from wa enable -> wa disable.

[How]
Clear address offset cache when viewport updates. Also update the
vp size check condition to account for rotation angle
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Upon exiting a fixed active VRR state, the state isn't cleared. This
leads to the variable VRR range to be calculated incorrectly.

[how]
Set fixed active state to false when updating vrr params
Signed-off-by: NAmanda Liu <amanda.liu@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The conversion to bool is not needed, remove it.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NChen Zhou <chenzhou10@huawei.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

read_current_link_settings_on_detect() on eDP 1.4+ may use the
edp_supported_link_rates table which is set up by
detect_edp_sink_caps(), so that function needs to be called first.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NMario Kleiner <mario.kleiner.de@gmail.com>
Cc: Martin Leung <martin.leung@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Only a single voltage level should be available to Pollock (min level)
Pollock & Dali get misidentified as Renoir, use wrong clk mgr constructor

[HOW]
Add provided Pollock IDs to ASIC Rev. ID list.
Create new Pollock ASIC RID check, fix RV2 & Dali ASIC checks.
Check RID and set max voltage level to 0 if Pollock is detected.
Work around broken ASICREV_IS_RENOIR, IS_RAVEN2, etc. checks by
performing Dali/Pollock checks before they can be misidentified as RN.
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It won't get used unless the driver allows the gtt domain for
display buffers which is controlled elsewhere.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

It won't get used unless the driver allows the gtt domain for
display buffers which is controlled elsewhere.
Acked-by: NHuang Rui <ray.huang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There is a use case that link loss happens accidentally,
and we need to recover that link loss as soon as possible.
Under this circumstance, we will perform link training,
and try to recover the link that's just lost.

However, if link PHY is disabled before link training
happens, then DP display will never come back again.

Also, please note that dropping this disable_phy function
call won't break USB-C hotplug functionality.
(This line of code was firstly introduced associated with
a patch to fix USB-C hotplug issue)

[How]
Don't disable DP transmitter and its encoder before link
training happens, even if link loss is detected.
Signed-off-by: NZhan Liu <zhan.liu@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Fix compilation warnings on i386 architecture:
undefined reference to `__udivdi3'
[how]
Switch DIV_ROUND_UP to DIV64_U64_ROUND_UP
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Compilation error "undefined reference to `__udivdi3'" was
thrown on i386 architecture.

[how]
Use div_u64 for unsigned long division instead of a divide operator.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Otherwise we get undefined symbols.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Whenever a connector on an MST network is attached, detached, or
undergoes a modeset, the DSC configs for each stream on that
topology will be recalculated. This can change their required
bandwidth, requiring a full reprogramming, as though a modeset
was performed, even if that stream did not change timing.

Therefore, whenever a crtc has drm_atomic_crtc_needs_modeset,
for each crtc that shares a MST topology with that stream and
supports DSC, add that crtc (and all affected connectors and
planes) to the atomic state and set mode_changed on its state

v2: Do this check only on Navi and before adding connectors
and planes on modesetting crtcs

v3: Call the drm_dp_mst_add_affected_dsc_crtcs() to update
all affected CRTCs
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Since for DSC MST connector's PBN is claculated differently
due to compression, we have to recalculate both PBN and
VCPI slots for that connector.

[how]
The function iterates through all the active streams to
find, which have DSC enabled, then recalculates PBN for
it and calls drm_dp_helper_update_vcpi_slots_for_dsc to
update connector's VCPI slots.

v2: - use drm_dp_mst_atomic_enable_dsc per port to
enable/disable DSC

v3: - Iterate through connector states from the state passed
    - On each connector state get stream from dc_state,
instead CRTC state
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If driver fails to update update VCPI allocation during
compute_mst_dsc_configs_for_state - fail the function
by return early.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If there is limited link bandwidth on a MST network,
it must be divided fairly between the streams on that network

Implement an algorithm to determine the correct DSC config
for each stream

The algorithm:
This
     [                   ]          ( )
represents the range of bandwidths possible for a given stream.
The [] area represents the range of DSC configs, and the ()
represents no DSC. The bandwidth used increases from left to right.

First, try disabling DSC on all streams
     [                  ]          (|)
     [                     ]            (|)
Check this against the bandwidth limits of the link and each branch
(including each endpoint). If it passes, the job is done

Second, try maximum DSC compression on all streams
that support DSC
     [|         ]        ( )
     [|                ]         ( )
If this does not pass, then enabling this combination of streams
is impossible

Otherwise, divide the remaining bandwidth evenly amongst the streams
     [        |  ]         ( )
     [        |      ]        ( )

If one or more of the streams reach minimum compression, evenly
divide the reamining bandwidth amongst the remaining streams
     [    |] ( )
     [       |]   ( )
     [                 |   ]               ( )
     [                 |      ]                  ( )

If all streams can reach minimum compression, disable compression
greedily
     [      |]  ( )
     [        |]    ( )
     [                 ]                                (|)

Perform this algorithm on each full update, on each MST link
with at least one DSC stream on it

After the configs are computed, call
dcn20_add_dsc_to_stream_resource on each stream with DSC enabled.
It is only after all streams are created that we can know which
of them will need DSC.

Do all of this at the end of amdgpu atomic check.  If it fails,
fail check; This combination of timings cannot be supported.

v2: Use drm_dp_mst_atomic_check to validate bw for certain dsc
configurations

v3: Use dc_dsc_policy structure to get min and max bpp rate
for DSC configuration
Acked-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Need to calculate VCPI slots differently for DSC
to take in account current link rate, link count
and FEC.
[how]
Add helper to get pbn_div from dc_link
Acked-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
For DSC case we cannot use topology manager's PBN divider
variable. The default divider does not take FEC into account.
Therefore the driver has to calculate its own divider based
on the link rate and lane count its handling, as it is hw specific.

[how]
Pass pbn_div as an argument, which is used if its more than
zero, otherwise default topology manager's pbn_div will be used.
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Rework the dm_helpers_write_dsc_enable callback to
handle the MST case.

Use the cached dsc_aux field.
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

During MST mode enumeration, if a new dc_sink is created,
populate it with dsc caps as appropriate.

Use drm_dp_mst_dsc_aux_for_port to get the raw caps,
then parse them onto dc_sink with dc_dsc_parse_dsc_dpcd.
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.

memset to 0 to avoid this
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>