The patch removes unneeded casts for the following (void *) pointers:
 - struct file: private
 - struct urb: context
 - struct usb_bus: hcpriv
 - return value of kmalloc()

The patch also contains some whitespace cleanup in the relevant areas.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This "u132-hcd" module is one half of the "driver" for
ELAN's U132 which is a USB to CardBus OHCI controller
adapter. This module needs the "ftdi-elan" module in
order to communicate to CardBus OHCI controller inserted
into the U132 adapter.

When the "ftdi-elan" module detects a supported CardBus
OHCI controller in the U132 adapter it loads this "u132-hcd"
module.

Upon a successful device probe() the single workqueue
is started up which does all the processing of commands
from the USB core that implement the host controller.

The workqueue maintains the urb queues and issues commands
via the functions exported by the "ftdi-elan" module. Each
such command will result in a callback.

Note that the "ftdi-elan" module is a USB client driver.

Note that this "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: NTony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This "ftdi-elan" module is one half of the "driver" for
ELAN's Uxxx series adapters which are USB to PCMCIA CardBus
adapters. Currently only the U132 adapter is available and
it's module is called "u132-hcd".

When the USB hot plug subsystem detects a Uxxx series adapter
it should load this module.

Upon a successful device probe() the jtag device file interface
is created and the status workqueue started up.

The jtag device file interface exists for the purpose of
updating the firmware in the Uxxx series adapter, but as
yet it had never been used.

The status workqueue initializes the Uxxx and then sits there
polling the Uxxx until a supported PCMCIA CardBus device is
detected it will start the command and respond workqueues
and then load the module that handles the device. This will
initially be only the u132-hcd module. The status workqueue
then just polls the Uxxx looking for card ejects.

The command and respond workqueues implement a command
sequencer for communicating with the firmware on the other
side of the FTDI chip in the Uxxx. This "ftdi-elan" module
exports some functions to interface with the sequencer.

Note that this module is a USB client driver.

Note that the "u132-hcd" module is a (cut-down OHCI)
host controller.

Thus we have a topology with the parent of a host controller
being a USB client! This really stresses the USB subsystem
semaphore/mutex handling in the module removal.
Signed-off-by: NTony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch to add support for Alcor Micro Corp. USB 2.0 TO RS-232 converter.
This patch adds VID and PID to pl2303.[ch], adds it to the "HORRIBLE
HACK FOR PL2303" in usb-serial.c and also prevents cdc-acm to claim
driving this device by blacklisting it in hid-core.
Signed-off-by: NJohannes Steingraeber <Jo_Stein@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NPaul B Schroeder <pschroeder@uplogix.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch is a driver for the PlayStation 2 specific Trance Vibrator
device. The only thing that device can do is vibrate at various speeds.
Signed-off-by: NSam Hocevar <sam@zoy.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Luiz Fernando N. Capitulino" <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for Ontrak ADU USB devices.

Fixed for printk issues by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NSteven Haigh <netwiz@crc.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings:
drivers/usb/serial/aircable.c:221: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
drivers/usb/serial/aircable.c:283: warning: format ‘%Zd’ expects type ‘signed size_t’, but argument 4 has type ‘int’
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: NNaranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When receiving a fatal error from the USB core, e.g. EILSEQ (which can
happen if the polling interval is too short), fail gracefully.
Previously the driver would fill the log with useless error messages
or (more alarmingly) silently spin forever trying to write updated
control information to the device.  This change implements a new flag
which if cleared indicates that the driver has failed.  The flag will
be set on initialization, cleared on fatal errors, and anything else
that touches the USB port in the driver will abort if the flag is
clear.  When the flag is cleared, a message will be logged indicating
that the driver has failed.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix usb core function error return checks to look for negative errno
values, not positive errno values.  This bug had rendered those checks
useless.  Also remove attempted error recovery on control endpoints
for EPIPE - with control endpoints EPIPE does not indicate a halted
endpoint so trying to recover with usb_clear_halt() is not the correct
action.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rather than directly filling in URB fields, it's safer to use
usb_fill_int_urb().  This improves robustness of the driver; URB
changes in the future will not go uninitialized here.  That point not
withstanding, this driver should at least be self-consistent.  Either
use usb_fill_int_urb() everywhere or don't bother with it all.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The polling interval for the device can't always be 1msec.  If it is
too quick, the device can fail causing a fatal (to the driver) EILSEQ
error from the USB core.  The actual correct value is reported by the
device as part of its configuration data, so use that value as the
default.  On a DeLorme Earthmate for example, the device reports that
it wants a 6msec interval.  As part of this fix, the "interval" module
option has been fixed as well; the device's default can be overridden
by specifying interval=<value> as a module option.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as786) removes a redundant test and fixes a problem
involving repeated system sleeps when CONFIG_USB_SUSPEND is not set.
During the first wakeup, the root hub's dev.power.power_state.event
field doesn't get updated, causing it not to be suspended during the
second sleep transition.

This takes care of the issue raised by Rafael J. Wysocki and Mattia
Dongili.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as740) removes the existing support for autosuspend of
root hubs.  That support fit in rather awkwardly with the rest of
usbcore and it was used only by ohci-hcd.  It won't be needed any more
since the hub driver will take care of autosuspending all hubs, root
or external.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as741) makes the non-hub parts of usbcore actually use the
autosuspend facilities added by an earlier patch.

	Devices opened through usbfs are autoresumed and then
	autosuspended upon close.

	Likewise for usb-skeleton.

	Devices are autoresumed for usb_set_configuration.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as739) adds the basic infrastructure for USB autosuspend
and autoresume.  The main features are:

	PM usage counters added to struct usb_device and struct
	usb_interface, indicating whether it's okay to autosuspend
	them or they are currently in use.

	Flag added to usb_device indicating whether the current
	suspend/resume operation originated from outside or as an
	autosuspend/autoresume.

	Flag added to usb_driver indicating whether the driver
	supports autosuspend.  If not, no device bound to the driver
	will be autosuspended.

	Mutex added to usb_device for protecting PM operations.
	Unlike the device semaphore, the locking rule for the pm_mutex
	is that you must acquire the locks going _up_ the device tree.

	New routines handling autosuspend/autoresume requests for
	interfaces and devices.

	Suspend and resume requests are propagated up the device tree
	(but not outside the USB subsystem).

	work_struct added to usb_device, for carrying out delayed
	autosuspend requests.

	Autoresume added (and autosuspend prevented) during probe and
	disconnect.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as778) adds a field to struct usb_device to store the
device's level in the USB tree.  In itself this number isn't really
important.  But the overhead is very low, and in a later patch it will
be used for preventing bogus warnings from the lockdep checker.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The command "cdrecord dev=/dev/uba x.iso" prints nasty garbage if a blank
is not in the drive. This happens because drivers have to set req->errors
separately from just returning zero uptodate with end_that_request_first,
end_that_request_last. These functions only set error in BIO, but sg_io()
ignores it.

Since we're on it, let cdrecord access a device when ->changed is set.
It's useful if someone wants to know device capabilities without burning
anything.
Signed-Off-By: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace spaces with tab and change comment indention for better readability.
Signed-off-by: NReiner Herrmann <reiner@reiner-h.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This includes two one-liners forwarded to me for the OHCI support on at91:

 - KB920x (and other boards with CPUs in non-BGA packages) need a slightly
   different way to say "ignore that port, it's not pinned out";

 - On resume, if we turn clocks on, record that we did so.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This updates the code handling dma-coherent buffer allocations, basically
reusing code from the musb_hdrc driver.  Instead of trying to work around two
significant limitations of the dma framework (memory wastage for buffers
smaller than a page, and inconsistency between calling context requirements
for allocation and free) this just works around one of them (the latter).

So count this as two steps forward (bugfixes:  the latter issue could cause
errors on some platforms, and some MIPS changes broke code for the former), 
and one step back (increasing cross-platform memory wastage).

Plus linelength and whitespace fixes; and minor data segment shrinkage.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adjust dev->dev_lock spinlock lock/unlock calls to be safe for SMP case.
Otherwise the following sequence may lead to a deadlock in SMP case:

gs_send()->usb_ep_queue()
	->(in case a request is satisfied immediatly) gs_write_complete()

for ex for pxa2xx_udc.c: 
usb_ep_queue()->pxa2xx_ep_queue()->write_fifo()->done()->gs_write_complete() 
(through req.complete pointer)
Signed-off-by: NEugeny S. Mints <emints@ru.mvista.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replaced kernel_thread() with kthread_run() since kernel_thread() is
deprecated in drivers/modules.
Signed-off-by: NCedric Le Goater <clg@fr.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For ep0out transfers (rare), be sure to copy the right data to userspace.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[ ... when you have an editor set to remind you of whitespace bugs ... ]

Cosmetic EHCI changes: remove end-of-line whitespace, spaces before tabs.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For systems using the Mentor HDRC controllers we get better TX DMA throughput
if we can avoid falling back to PIO to write zero length packets ... so tell
the driver to avoid ZLPs.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as755b) fixes a bug in usbmon.  Rather than assuming all
USB host controllers use DMA, the code will check the usb_bus data
structure.  If DMA isn't used, we don't want to try peeking into a
non-existent DMA buffer!
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As part of the ongoing program to flatten out the HCD bus-glue layer,
this patch (as771b) eliminates the hcpriv, release, and kref fields
from struct usb_bus.  hcpriv and release were not being used for
anything worthwhile, and kref has been moved into the enclosing
usb_hcd structure.

Along with those changes, the patch gets rid of usb_bus_get and
usb_bus_put, replacing them with usb_get_hcd and usb_put_hcd.

The one interesting aspect is that the dev_set_drvdata call was
removed from usb_put_hcd, where it clearly doesn't belong.  This means
the driver private data won't get reset to NULL.  It shouldn't cause
any problems, since the private data is undefined when no driver is
bound.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as770b) introduces a new field to usb_bus: a flag
indicating whether or not the host controller uses DMA.  This serves
to encapsulate the computation.  It also means we will have only one
spot to update if the DMA API changes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All of the currently-supported USB host controller drivers use the HCD
bus-glue framework.  As part of the program for flattening out the glue
layer, this patch (as769) removes the usb_operations structure.  All
function calls now go directly to the HCD routines (slightly renamed
to remain within the "usb_" namespace).

The patch also removes usb_alloc_bus(), because it's not useful in the
HCD framework and it wasn't referenced anywhere.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix CONFIG_PM=n build.

Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/core/hub.c: In function `hub_events':
drivers/usb/core/hub.c:2591: warning: statement with no effect
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>