We can remove the NULL check here.  It triggers a Smatch warning because
list_first_entry() never is NULL and people who check for it normally
intend to check for list_empty() instead.  In these cases however,
we've already verified that the lists are not empty.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

kvalo: do the same changes for ar6004 hw1.2 as well

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.

kvalo: fix commit log
Signed-off-by: NMing Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

System crash because of NULL pointer reference due to
cleanup_scatter is not implemented for USB.
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If, in
drivers/net/wireless/ath/ath6kl/debug.c::ath6kl_fwlog_block_read(),
the call to wait_for_completion_interruptible() returns -ERESTARTSYS
then we'll return without freeing the (as yet unused) memory we
allocated for 'buf' - thus leaking it.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add the necessary change for AR6004 1.2 chip support
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.

kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath5k: Remove extraneous statements from ath5k_hw_proc_4word_tx_status and ath5k_hw_proc_2word_status.
Signed-off-by: NQasim Javed <qasimj@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Semicolons are not necessary after macros that end in while (0).
Remove them.

Simplify the macros with tests of
do { if (foo>size) memset1; else memset2;} while (0);
to a single line memset(,,min_t(size_t, foo, size))
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds counters in various places that can drop packets on
rx without otherwise incrementing a counter.  It also counts
some non-error cases, such as becons and fragments received.

Should help with figuring out where packets are (and are not)
dropped.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Follow updates in DFS pattern detector interface:
a) use given pulse event structure
b) adapt to boolean return value of add_pulse()
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.

Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.

To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.

Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.

Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.

Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.

Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Macros can be converted to functions to reduce overall object size.

Convert the ATH5K_PRINTK macro to use _ath5k_printk.

Allyesconfig size is reduced ~10%

$ size drivers/net/wireless/ath/ath5k/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 211557	   2032	  40672	 254261	  3e135	drivers/net/wireless/ath/ath5k/built-in.o.new
 235412	   2032	  47296	 284740	  45844	drivers/net/wireless/ath/ath5k/built-in.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.

* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature

This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.

Cc: Paul Stewart <pstew@google.com>
Reported-by: NGary Morain <gmorain@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch improves ANI operations by switching among the immunity
levels based on PHY errors and beacon rssi which will adjust receiver
desensitizing parameters. The changes are

* Configure the Weak Signal Detection based on current immunity value.
* At highest OFDM immunity level poor performance was observed with
  strong interference. By tuning the FIR step and spur immunity levels
  and not changing any weak signal detection thresholds at any level
  helped to improve the performance.
* ANI took long time to recover back to lower immunity levels on heavy
  data load. As the listen time got reset to zero before reaching to
  the 5x of aniperiod, the immunity level is not lowering back even
  without any interference. This patch fix that.

Cc: Paul Stewart <pstew@google.com>
Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com>
Signed-off-by: NSuresh Chandrasekaran <csuresh@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSN capability field of RSN IE which is generated (which is what really
advertised in beacon/probe response) differs from the one generated in
wpa_supplicant. This inconsistency in rsn IE results in 4-way handshake
failure. To fix this, configure rsn capability used in wpa_supplicant
in firmware using a new wmi command, WMI_SET_IE_CMDID. There is a bit
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) in fw_capabilities to advertise
this support to driver.
Signed-off-by: NSubramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch disables HT in start_ap if the type of the channel on
which the AP mode is going to be operating is non-HT. HT is enabled
with default ht cap setting if the operating channel is going to be
11n.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HT40 is not supported in 2.4Ghz.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Using interface 0 for p2p causes target assert. This is because
interface 0 is always initialized to non-p2p operations. Fix this
issue by initializing all the interfaces for p2p when fw is capable
of dynamic interface switching. When fw is not capable of dynamic
switching, make sure p2p is not brought up on interface which is
not initialized for this purpose.

Reported-by: Naveen Singh navesing@qca.qualcomm.com
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

net_stats.multicast is updated with the count of received multicast packets.

kvalo: indentation changes
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When a scan request is pending while going to suspend, any new
scan request after resume will fail. So, cancel all scan requests
in all the vifs before moving to suspend state.
Signed-off-by: NPingYang Zhang <pingzhan@qca.qualcomm.com>
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes it has been observed that allocating a contiguous memory
of more than 100K fails with kmalloc. This has been modified to
use vmalloc instead.
Signed-off-by: NPingYang Zhang <pingzhan@qca.qualcomm.com>
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

After connect command, send scan params WMI command to
set background scan period. If period value is zero
send 0xffff as bg scan period to disable bg scan.
Set default bg scan period to be 60 seconds if
not specified.

This patch depends on below patch
cfg80211: Add background scan period attribute.

kvalo: fix open parenthesis alignment
Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In current code, Scan request info is recorded in vif->scan_req
after sending SCAN request to the firmware in ath6kl_cfg80211_scan().

In some corner cases, firmware sends SCAN_COMPLETE event immediately
when it receives SCAN request, which internally executes scan
complete event handler ath6kl_cfg80211_scan_complete_event() first.
So, Scan completion handler will a get a chance to executed even
before storing scan request info in ath6kl_cfg80211_scan().

Scan completion handler never report SCAN_COMPLETE event to
cfg80211 if scan request info(vif->scan_req) is NULL. This leads
to scan failure issue ("Device or resource busy error") during
next SCAN request from the user space. This patch ensures that scan
request info is stored before sending SCAN request.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

commit 0d95521e (ath9k: use split rx buffers to get rid of order-1 skb
allocations) added in memory leak in error path.

sc->rx.frag should be cleared after the pskb_expand_head() call, or else
we jump to requeue_drop_frag and leak an skb.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.

Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NMadhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now, with HTC pipe, it's possible to fully support USB version of AR6004.

Based on code by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is needed for USB.

Based on code by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In preparation for adding HTC pipe implementation add htc-ops.h to make
it possible dynamically choose which HTC type is used.

Needed for full USB support.

Based on the code by Ray Chen <raychen@qca.qualcomm.com>.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>