AM35x has musb interface and uses CPPI4.1 DMA engine.
Current patch supports only PIO mode. DMA support can be
added later once basic CPPI4.1 DMA patch is accepted.

Also added USB_MUSB_AM35X which is required to differentiate musb ips
between OMAP3x and AM35x. This config would be used to for below
purposes,
        - Select am35x.c instead of omap2430.c for compilation
          at drivers/usb/musb directory. Please note there are
          significant differneces in these two files as musb ip
          in quite different on AM35x.

	  Please note that in multi omap configuration only omap2430.c
	  file will get compiled and we would require to select only
	  AM35x based board config to compile am35x.c

        - Select workaround codes applicable for AM35x musb issues.
          one such workaround is for bytewise read issue on AM35x.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix these linker errors when CONFIG_PM=n:

ERROR: "xhci_bus_resume" [drivers/usb/host/xhci-hcd.ko] undefined!
ERROR: "xhci_bus_suspend" [drivers/usb/host/xhci-hcd.ko] undefined!
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix this error when CONFIG_PM is not enabled:

drivers/usb/host/xhci.c:675: error: implicit declaration of function 'usb_root_hub_lost_power'

Wrap xhci_suspend() and xhci_resume() into an ifdef CONFIG_PM, along with
the functions that only they call -- xhci_save_registers() and
xhci_restore_registers().
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A few devices (such as the RCA VR5220 voice recorder) are so
non-compliant with the USB spec that they have invalid maxpacket sizes
for endpoint 0.  Nevertheless, as long as we can safely use them, we
may as well do so.

This patch (as1432) softens our acceptance criterion by allowing
high-speed devices to have ep0-maxpacket sizes other than 64.  A
warning is printed in the system log when this happens, and the
existing error message is clarified.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NJames <bjlockie@lockie.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements the PCI suspend/resume.

Please refer to xHCI spec for doing the suspend/resume operation.

For S3, CSS/SRS in USBCMD is used to save/restore the internal state.
However, an error maybe occurs while restoring the internal state.
In this case, it means that HC internal state is wrong and HC will be
re-initialized.
Signed-off-by: NLibin Yang <libin.yang@amd.com>
Signed-off-by: NDong Nguyen <dong.nguyen@amd.com>
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements xHCI bus suspend/resume function hook.

In the patch it goes through all the ports and suspend/resume
the ports if needed.

If any port is in remote wakeup, abort bus suspend as what ehci/ohci do.
Signed-off-by: NLibin Yang <libin.yang@amd.com>
Signed-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit implements port remote wakeup.

When a port is in U3 state and resume signaling is detected from a device,
the port transitions to the Resume state, and the xHC generates a Port Status
Change Event.

For USB3 port, software write a '0' to the PLS field to complete the resume
signaling. For USB2 port, the resume should be signaling for at least 20ms,
irq handler set a timer for port remote wakeup, and then finishes process in
hub_control GetPortStatus.

Some codes are borrowed from EHCI code.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add software trigger USB device suspend resume function hook.
Do port suspend & resume in terms of xHCI spec.

Port Suspend:
Stop all endpoints via Stop Endpoint Command with Suspend (SP) flag set.
Place individual ports into suspend mode by writing '3' for Port Link State
(PLS) field into PORTSC register. This can only be done when the port is in
Enabled state. When writing, the Port Link State Write Strobe (LWS) bit shall
be set to '1'.
Allocate an xhci_command and stash it in xhci_virt_device to wait completion for
the last Stop Endpoint Command.  Use the Suspend bit in TRB to indicate the Stop
Endpoint Command is for port suspend. Based on Sarah's suggestion.

Port Resume:
Write '0' in PLS field, device will transition to running state.
Ring an endpoints' doorbell to restart it.

Ref: USB device remote wake need another patch to implement. For details of
how USB subsystem do power management, please see:
    Documentation/usb/power-management.txt
Signed-off-by: NCrane Cai <crane.cai@amd.com>
Signed-off-by: NLibin Yang <libin.yang@amd.com>
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the system suspends and a host controller's power is lost, the USB
core attempts to revive any USB devices that had the persist_enabled flag
set.  For non-SuperSpeed devices, it will disable the port, and then set
the udev->reset_resume flag.  This will cause the USB core to reset the
device, verify the device descriptors to make sure it's the same device,
and re-install any non-default configurations or alternate interface
settings.

However, we can't disable SuperSpeed root hub ports because that turns off
SuperSpeed terminations, which will inhibit any devices connecting at USB
3.0 speeds.  (Plus external hubs don't allow SuperSpeed ports to be
disabled.)

Because of this logic in hub_activate():
                /* We can forget about a "removed" device when there's a
                 * physical disconnect or the connect status changes.
                 */
                if (!(portstatus & USB_PORT_STAT_CONNECTION) ||
                                (portchange & USB_PORT_STAT_C_CONNECTION))
                        clear_bit(port1, hub->removed_bits);

                if (!udev || udev->state == USB_STATE_NOTATTACHED) {
                        /* Tell khubd to disconnect the device or
                         * check for a new connection
                         */
                        if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
                                set_bit(port1, hub->change_bits);

                } else if (portstatus & USB_PORT_STAT_ENABLE) {
                        /* The power session apparently survived the resume.
                         * If there was an overcurrent or suspend change
                         * (i.e., remote wakeup request), have khubd
                         * take care of it.
                         */
                        if (portchange)
                                set_bit(port1, hub->change_bits);

                } else if (udev->persist_enabled) {
                        udev->reset_resume = 1;
                        set_bit(port1, hub->change_bits);

                } else {
                        /* The power session is gone; tell khubd */
                        usb_set_device_state(udev, USB_STATE_NOTATTACHED);
                        set_bit(port1, hub->change_bits);
                }

a SuperSpeed device after a resume with a loss of power will never get the
reset_resume flag set.  Instead the core will assume the power session
survived and that the device still has the same address, configuration,
and alternate interface settings.  The xHCI host controller will have no
knowledge of the device (since all xhci_virt_devices were destroyed when
power loss was discovered, and xhci_discover_or_reset_device() has not
been called), and all URBs to the device will fail.

If the device driver responds by resetting the device, everything will
continue smoothly.  However, if lsusb is used before the device driver
resets the device (or there is no driver), then all lsusb descriptor
fetches will fail.

The quick fix is to pretend the port is disabled in hub_activate(), by
clearing the local variable.  But I'm not sure what other parts of the hub
driver need to be changed because they have assumptions about when ports
will be disabled.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xHCI driver uses hardware assigned device address. This may cause device
address conflict in certain cases.

Use kernel assigned address for devices under xHCI. Store the xHC assigned
address locally in xHCI driver.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Rename xhci_reset_device() to xhci_discover_or_reset_device().
If xhci_discover_or_reset_device() is called to reset a device which does
not exist or does not match the udev, it calls xhci_alloc_dev() to
re-allocate the device.

This would prevent the reset device failure, possibly due to the xHC restore
error during S3/S4 resume.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a pointer to udev in struct xhci_virt_device. When allocate a new
virt_device, make the pointer point to the corresponding udev.

Modify xhci_check_args(), check if virt_dev->udev matches the target udev,
to make sure command is issued to the right device.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some functions changed by 1c98347e.
However, There was a change mistake of the function (outsw).
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Paul Mundt <lethal@linux-sh.org>
Cc: stable <stable@kernel.org>  [.35 & .36]
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Extend id's table to have ulpi phy names in it.
Report if the known phy is found.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Improve ulpi phy detection by utilizing the "scratch" register.
Allow unknown ulpi phy work without the need to hard-code the id.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlon Ziv <alon-git@nolaviz.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OPN2001 expects write operations to arrive as a vendor-specific command
through the control pipe (instead of using a separate bulk-out pipe).
Signed-off-by: NAlon Ziv <alon-git@nolaviz.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bulk-read callback had two bugs:
a) The bulk-in packet's leading two zeros were returned (and the two last
   bytes truncated)
b) The wrong URB was transmitted for the second (and later) read requests,
   causing further reads to return the entire packet (including leading
   zeros)
Signed-off-by: NAlon Ziv <alon-git@nolaviz.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

No need to set latency timeout at every open.

This also fixes an issue with the read latency being as high as 250ms
(instead of 1ms) for the first read after port probe.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the iowarrior devices in this case statement support more than 8 bytes
per report, it is possible to write past the end of a kernel heap allocation.
This will probably never be possible, but change the allocation to be more
defensive anyway.
Signed-off-by: NKees Cook <kees.cook@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix regression introduced by commit
214916f2 (USB: visor: reimplement using
generic framework) which broke initialisation of UX50/TH55 devices that
used re-mapped bulk-out endpoint addresses.
Reported-by: NRobert Gadsdon <rgadsdon@bayarea.net>
Tested-by: NRobert Gadsdon <rgadsdon@bayarea.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch for FTDI USB serial driver ads new VID/PIDs used on various
devices manufactured by Papouch (http://www.papouch.com). These devices
have their own VID/PID, although they're using standard FTDI chip. In
ftdi_sio.c, I also made small cleanup to have declarations for all
Papouch devices together.
Signed-off-by: NDaniel Suchy <danny@danysek.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit changes storage_common.h, file_storage.c and
f_mass_storage.c to use definitions of SCSI commands from
scsi/scsi.h file instead of redefining the commands in
storage_common.c.

scsi/scsi.h header file was missing READ_FORMAT_CAPACITIES and
READ_HEADER so this commit also add those to the header.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.

None of the dependencies are modified.
Signed-off-by: Nmatt mooney <mfm@muteddisk.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In function dummy_udc_probe()
call put_device() when device_register() fails.
also usb_get_hcd() put before device_register() after review comment
from Alan Stern.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In function usb_create_ep_devs()
call put_device() when device_register() fails.
Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The WAGO 750-923 USB Service Cable is used for configuration and firmware
updates of several industrial automation products from WAGO Kontakttechnik GmbH.

Bus 004 Device 002: ID 1be3:07a6
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x1be3
  idProduct          0x07a6
  bcdDevice            1.00
  iManufacturer           1 Silicon Labs
  iProduct                2 WAGO USB Service Cable
  iSerial                 3 1277796751
  . . .
Signed-off-by: NAnders Larsen <al@alarsen.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At otg device mode, the otg host resume should do no-op during
system resume, otherwise, the otg device will be treated as a
host for enumeration.

So, the otg host driver returns -ESHUTDOWN if it detects the
current usb mode is device mode. The host driver has to return
-ESHUTDOWN, otherwise, the usb_hc_died will be called.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some Rockbox based mp4 players will crash when ever they see a
read_capacity_16 scsi command.  So add a new US_FL which tells the scsi sd
driver to not issue any read_capacity_16 scsi commands.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I seem to have a knack for digging up buggy usb devices which don't work
with Linux, and I'm crazy enough to try to make them work.  So this time a
friend of mine asked me to get an mp4 player (an mp3 player which can play
videos on a small screen) to work with Linux.

It is based on the well known rockbox chipset for which we already have an
unusual devs entries to work around some of its bugs.  But this model
comes with an additional twist.

This model chokes on read_capacity_16 calls.  Now normally we don't make
those calls, but this model comes with an sdcard slot and when there is no
card in there (and shipped from the factory there is none), it reports a
size of 0.  However this time the programmers actually got the
read_capacity_10 response right!  So they substract one from the size as
stored internally in the mp3 player before reporting it back, resulting in
an answer of ...  0xffffffff sectors, causing sd.c to try a
read_capacity_16, on which the device crashes.

This patch adds a flag to scsi_device to indicate that a a device cannot
handle read_capacity_16, and when this flag is set if a device reports an
lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to
report a size of 0.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Appotech ax3003 (the larger brother of the ax203) based devices are even
more buggy then the ax203.  They will go of into lala land when ever they
see a READ_DISC_INFO scsi command.  So add a new US_FL which tells the
scsi sr driver to not issue any READ_DISC_INFO scsi commands.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device,
usually this fake cdrom contains the windows software for the device.
While working on supporting Appotech ax3003 based photoframes, which do
this I discovered that they will go of into lala land when ever they see a
READ_DISC_INFO scsi command.

Thus this patch adds a scsi_device flag (which can then be set by the
usb-storage driver through an unsual-devs entry), to indicate this, and
makes the sr driver honor this flag.

I know this sucks, but as discussed on linux-scsi list there is no other
way to make this device work properly.

Looking at usb traces made under windows, windows never sends a
READ_DISC_INFO during normal interactions with a usb cdrom device.  So as
this cdrom emulation thingie becomes more common we might see more of this
problem.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is based on an initial patch by Rahul Ruikar.

The goku_remove() function can be called before device_register() so it
can call device_unregister() improperly.  Also if the call to
device_register() fails we need to call put_device().

As I was changing the error handling in goku_probe(), I noticed that
the label was "done" but actually if the function succeeds we return
earlier.  I renamed the error path to "err" instead of "done."
Reported-by: NRahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The hardware can only do DMA to 4 byte aligned addresses.
When this requirement is not met use PIO or a bounce buffer.

PIO is used when the buffer is small enough to directly
use the hardware data memory (2*maxpacket).

A bounce buffer is used for larger transfers.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Split unmap_urb_for_dma() to allow just the setup buffer
to be unmapped. This allows HCDs to use PIO for the setup
buffer if it is not suitable for DMA.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Release the hardware resources and reset the internal HCD state
associated with an isochronous endpoint when the last URB queued
for it completes.

Previously this was only done in then endpoint_disable() method
causing usbtest 15 and 16 to hang when run twice in succession
without a disconnect.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We already have fields describing the hardware data memory
(dmem_size and dmem_offset) in the HCD private data,
use them rather than the rather obscure read from the
hardware descriptor.
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>