This adds the Designware compatible watchdog found on RK3xxx Cortex-A9 SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

We set default pinctrl settings for the uarts in rk3188.dtsi already,
so remove forgotten duplicate.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This adds a device tree node for the infrared receiver connected to a
GPIO pin on the Radxa Rock.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This adds the necessary nodex and pinctrl settings for the Rockchip PWM-driver.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>

Modified to use the new clock defines and added rk3066 pins.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Use the newly ammended dw_8250 clock binding to define both the baudclk as
well as the pclk supplying the ip.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The Radxa Rock contains one sd-card slot. Add the supplying regulator
and enable its dw_mmc node.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This enables the 2nd i2c bus and adds the act8846 pmic as device.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The Curie2 uses a tps659102 as its main pmic, so add the i2c1 and tps65910
node as well as define the used voltages and regulator-names according to
the schematics.

Also fix the supply of the sd0 regulator, as it is supplied by the vio reg.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The core controller settings themself are identical, only the compatible and
pinctrl settings differ.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

To create some sort of ordering of nodes, they are suggested to be ordered by
their register address.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The pincontroller uses the GRF and PMU syscons nowadays, so should not
contain an address in its device node.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Use the handles for subsequent changes to nodes, similar to like the rk3288
submission does it.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Some nodes that are changed in the dtsi hierarchy do not have handles yet.
As it was suggested in the rk3288 submission to do subsequent nodes changes
through such handle-references, add the missing ones.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Comments received from the rk3288 submission indicated that a generic subnode
to group soc components should not be used.

So to keep all rockchip devicetree files similar, remove it from rk3066 and rk3188.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The clock and reset unit is now provided by the rk3188-cru clock driver and thus
the old style definitions of the gate clocks can go away.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>

The clock definitions get a lot shorter due to the soc clocks being handled by
rk3188-cru and only the input clock remains. These can now simply live
in the main rk3xxx.dtsi without affecting readability.

At the same time, rename the node to oscillator, adding a clock-output-names
property to match how the rk3288 handles this.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>

This adds a node for the clock and reset unit on rk3188 and rk3066 SoCs and
also updates the device nodes retrieve their clocks from there, instead of
the previous gate clock nodes.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>

All known Rockchip SoCs have a reset controller in their CRUs, so it's
helpful to have the reset controller framework selected by default,
only be deselected by the user in special cases.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add the clock tree definition for the new rk3288 SoC.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds the dt-binding documentation for the clock and reset unit found on
Rockchip rk3288 SoCs.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds a clock driver that handles the specific muxes, dividers and gates
of rk3188 and rk3066 SoCs.

The structure of the clock list resembles the arrangement of their
counterparts in the clock architecture diagrams found in the SoC
documentation.

Clocks exported to the clock provider are currently limited to well known
or measured ones. So additional clock exports may be necessary in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This add bindings documentation for the clock and reset unit found on
rk3188 and rk3066 SoCs from Rockchip.

Also deprecate the old gate clock binding, as these shouldn't be used
in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

All Rockchip SoCs at least down to the ARM9-based RK28xx include the reset-
controller for SoC peripherals in their clock controller.
While the older SoCs (ARM9 and Cortex-A8) use a regular scheme to change
register values, the Cortex-A9 SoCs use a hiword-mask making locking unecessary.
To be compatible with both schemes the reset controller takes a flag to
decide which scheme to use, similar to the other HIWORD_MASK flags used in the
clock framework.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

All known Rockchip SoCs down to the RK28xx (ARM9) use a similar pattern to
handle their plls:
                       |--\
xin32k ----------------|mux\
xin24m -----| pll |----|pll|--- pll output
       \---------------|src/
                       |--/

The pll output is sourced from 1 of 3 sources, the actual pll being one of
them. To change the pll frequency it is imperative to remux it to another
source beforehand. This is done by adding a clock-listener to the pll that
handles the remuxing before and after the rate change.

The output mux is implemented as a separate clock to make use of already
existing common-clock features for disabling the pll if one of the other
two sources is used.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds infrastructure for registering clock branches. On Rockchip SoCs
most clock branches are a combination of mux,divider and gate components,
thus a composite clock is used when appropriate.

Clock branches are supposed to be declared in an array using the COMPOSITE*
or MUX, etc makros defined in the header and then registered using
rockchip_clk_register_branches.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The function pointer population and sanity checking logic got a bit ugly
with the advent of the .determine_rate callback. Clean it up.
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This allows readl-only composite clocks by making mux_ops->set_parent and
divider_ops->round_rate/set_rate optional.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

In case the rate_hw does not implement determine_rate, but only round_rate
we fallback to best_parent selection if mux_hw is present and support
reparenting.

This also fixes a rate calculation problem when using the standard div and
mux ops, as in this case currently only the mux->determine_rate is used
in the composite rate calculation.
So when for example the composite clock has two parents at 600 and 800MHz,
the requested rate is 75MHz, which the divider could provide, without this
change the rate would be set 600MHz ignoring the divider completely.
This may be way out of spec for the component.
Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
[heiko@sntech.de: fixed output return a rate instead of the diff]
Acked-By: NMax Schwarz <max.schwarz@online.de>
Tested-By: NMax Schwarz <max.schwarz@online.de>
Tested-by: NGabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Pull ARM fixes from Russell King:
 "Another round of ARM fixes.  The largest change here is the L2 changes
  to work around problems for the Armada 37x/380 devices, where most of
  the size comes down to comments rather than code.

  The other significant fix here is for the ptrace code, to ensure that
  rewritten syscalls work as intended.  This was pointed out by Kees
  Cook, but Will Deacon reworked the patch to be more elegant.

  The remainder are fairly trivial changes"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
  ARM: 8086/1: Set memblock limit for nommu
  ARM: 8085/1: sa1100: collie: add top boot mtd partition
  ARM: 8084/1: sa1100: collie: revert back to cfi_probe
  ARM: 8080/1: mcpm.h: remove unused variable declaration
  ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache

Note that I don't maintain Documentation/ABI/,
Documentation/devicetree/, or the language translation files.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These days most people use git to send patches so I have added a section
about that.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.

This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: NKees Cook <keescook@chromium.org>
Tested-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 1c2f87c2 (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: NLaura Abbott <lauraa@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Reverts commit d26b17ed
ARM: sa1100: collie.c: fall back to jedec_probe flash detection

Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.

Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.

To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.

Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.

While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.

Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pull spi fixes from Mark Brown:
 "A few driver specific fixes, the biggest one being a fix for the newly
  added Qualcomm SPI controller driver to make it not use its internal
  chip select due to hardware bugs, replacing it with GPIOs"

* tag 'spi-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: qup: Remove chip select function
  spi: qup: Fix order of spi_register_master
  spi: sh-sci: fix use-after-free in sh_sci_spi_remove()
  spi/pxa2xx: fix incorrect SW mode chipselect setting for BayTrail LPSS SPI

Pull regulator fixes from Mark Brown:
 "Several driver specific fixes here, the palmas fixes being especially
  important for a range of boards - the recent updates to support new
  devices have introduced several regressions"

* tag 'regulator-v3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: tps65218: Correct the the config register for LDO1
  regulator: tps65218: Add the missing of_node assignment in probe
  regulator: palmas: fix typo in enable_reg calculation
  regulator: bcm590xx: fix vbus name
  regulator: palmas: Fix SMPS enable/disable/is_enabled