- 28 10月, 2014 5 次提交
-
-
由 Ian Munsie 提交于
In certain circumstances the PSL (Power Service Layer, which provides translation services for CXL hardware) can send an interrupt for a segment miss that the kernel has already handled. This can happen if multiple translations for the same segment are queued in the PSL before the kernel has restarted the first translation. The CXL driver does not expect this situation and does not check if a segment had already been handled. This could cause a duplicate segment table entry which in turn caused a PSL error taking down the card. This patch fixes the issue by checking for existing entries in the segment table that match the segment we are trying to insert, so as to avoid inserting duplicate entries. Signed-off-by: NIan Munsie <imunsie@au1.ibm.com> Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Ian Munsie 提交于
This patch makes copro_calculate_slb() mask the ESID by the correct mask for 1T vs 256M segments. This has no effect by itself as the extra bits were ignored, but it makes debugging the segment table entries easier and means that we can directly compare the ESID values for duplicates without needing to worry about masking in the comparison. This will be used to simplify a comparison in the following patch. Signed-off-by: NIan Munsie <imunsie@au1.ibm.com> Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Ian Munsie 提交于
This moves the segment table hash calculation from cxl_load_segment() into find_free_sste() since that is the only place it is actually used. Signed-off-by: NIan Munsie <imunsie@au1.ibm.com> Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Ian Munsie 提交于
This patch simplifies the process of finding a free segment table entry by disabling the secondary hash. This reduces the number of possible entries in the segment table for a given address from 16 to 8. Due to the large segment sizes we use it is extremely unlikely that the secondary hash would ever have been used in practice, so this should not have any negative impacts and may even improve performance due to the reduced number of comparisons that software & hardware need to perform. This patch clears the SC bit in the hardware's state register (CXL_PSL_SR_An) to disable the secondary hash in the hardware since we can no longer fill out entries using it. Signed-off-by: NIan Munsie <imunsie@au1.ibm.com> Reviewed-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Michael Ellerman 提交于
This reverts commit bf7588a0. Ben says although the code is not correct "[this] fix was completely wrong and does more damages than it fixes things." Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 23 10月, 2014 1 次提交
-
-
由 Jeremy Kerr 提交于
Currently, we can't call opal wrappers from modules when using the LE ABIv2, which requires a TOC init. If we do we'll try and load the opal entry point using the wrong toc and probably explode or worse jump to the wrong address. Nothing in upstream is making opal calls from a module, but we do export one of the wrappers so we should fix this anyway. This change uses the _GLOBAL_TOC() macro (rather than _GLOBAL) for the opal wrappers, so that we can do non-local calls to them. Signed-off-by: NJeremy Kerr <jk@ozlabs.org> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 22 10月, 2014 7 次提交
-
-
由 Pranith Kumar 提交于
This patch wires up the new syscall sys_bpf() on powerpc. Passes the tests in samples/bpf: #0 add+sub+mul OK #1 unreachable OK #2 unreachable2 OK #3 out of range jump OK #4 out of range jump2 OK #5 test1 ld_imm64 OK #6 test2 ld_imm64 OK #7 test3 ld_imm64 OK #8 test4 ld_imm64 OK #9 test5 ld_imm64 OK #10 no bpf_exit OK #11 loop (back-edge) OK #12 loop2 (back-edge) OK #13 conditional loop OK #14 read uninitialized register OK #15 read invalid register OK #16 program doesn't init R0 before exit OK #17 stack out of bounds OK #18 invalid call insn1 OK #19 invalid call insn2 OK #20 invalid function call OK #21 uninitialized stack1 OK #22 uninitialized stack2 OK #23 check valid spill/fill OK #24 check corrupted spill/fill OK #25 invalid src register in STX OK #26 invalid dst register in STX OK #27 invalid dst register in ST OK #28 invalid src register in LDX OK #29 invalid dst register in LDX OK #30 junk insn OK #31 junk insn2 OK #32 junk insn3 OK #33 junk insn4 OK #34 junk insn5 OK #35 misaligned read from stack OK #36 invalid map_fd for function call OK #37 don't check return value before access OK #38 access memory with incorrect alignment OK #39 sometimes access memory with incorrect alignment OK #40 jump test 1 OK #41 jump test 2 OK #42 jump test 3 OK #43 jump test 4 OK Signed-off-by: NPranith Kumar <bobby.prani@gmail.com> [mpe: test using samples/bpf] Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Dan Streetman 提交于
Change maintainer of nx-842 compression coprocessor driver to Dan Streetman. Signed-off-by: NDan Streetman <ddstreet@ieee.org> Acked-by: NNathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Aneesh Kumar K.V 提交于
Remove the check of CONFIG_PPC_SUBPAGE_PROT when deciding if is_hugepage_only_range() is extern or inline. The extern version is in slice.c and is built if CONFIG_PPC_MM_SLICES=y. There was no build break possible because CONFIG_PPC_SUBPAGE_PROT is only selectable under conditions which also mean CONFIG_PPC_MM_SLICES will be selected. Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Aneesh Kumar K.V 提交于
arch/powerpc/mm/slice.c:704:5: error: expected identifier or ‘(’ before numeric constant int is_hugepage_only_range(struct mm_struct *mm, unsigned long addr, ^ make[1]: *** [arch/powerpc/mm/slice.o] Error 1 make: *** [arch/powerpc/mm/slice.o] Error 2 This got introduced via 1217d34b "powerpc: Ensure global functions include their prototype". We started including linux/hugetlb.h with that patch and now we have #define is_hugepage_only_range(mm, addr, len) 0 with hugetlbfs disabled. Fixes: 1217d34b ("powerpc: Ensure global functions include their prototype") Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending由 Linus Torvalds 提交于
Pull SCSI target updates from Nicholas Bellinger: "Here are the target updates for v3.18-rc2 code. These where originally destined for -rc1, but due to the combination of travel last week for KVM Forum and my mistake of taking the three week merge window literally, the pull request slipped.. Apologies for that. Things where reasonably quiet this round. The highlights include: - New userspace backend driver (target_core_user.ko) by Shaohua Li and Andy Grover - A number of cleanups in target, iscsi-taret and qla_target code from Joern Engel - Fix an OOPs related to queue full handling with CHECK_CONDITION status from Quinn Tran - Fix to disable TX completion interrupt coalescing in iser-target, that was causing problems on some hardware - Fix for PR APTPL metadata handling with demo-mode ACLs I'm most excited about the new backend driver that uses UIO + shared memory ring to dispatch I/O and control commands into user-space. This was probably the most requested feature by users over the last couple of years, and opens up a new area of development + porting of existing user-space storage applications to LIO. Thanks to Shaohua + Andy for making this happen. Also another honorable mention, a new Xen PV SCSI driver was merged via the xen/tip.git tree recently, which puts us now at 10 target drivers in upstream! Thanks to David Vrabel + Juergen Gross for their work to get this code merged" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (40 commits) target/file: fix inclusive vfs_fsync_range() end iser-target: Disable TX completion interrupt coalescing target: Add force_pr_aptpl device attribute target: Fix APTPL metadata handling for dynamic MappedLUNs qla_target: don't delete changed nacls target/user: Recalculate pad size inside is_ring_space_avail() tcm_loop: Fixup tag handling iser-target: Fix smatch warning target/user: Fix up smatch warnings in tcmu_netlink_event target: Add a user-passthrough backstore target: Add documentation on the target userspace pass-through driver uio: Export definition of struct uio_device target: Remove unneeded check in sbc_parse_cdb target: Fix queue full status NULL pointer for SCF_TRANSPORT_TASK_SENSE qla_target: rearrange struct qla_tgt_prm qla_target: improve qlt_unmap_sg() qla_target: make some global functions static qla_target: remove unused parameter target: simplify core_tmr_abort_task target: encapsulate smp_mb__after_atomic() ...
-
git://git.open-osd.org/linux-open-osd由 Linus Torvalds 提交于
Pull email address change from Boaz Harrosh. * 'for-linus' of git://git.open-osd.org/linux-open-osd: Boaz Harrosh - fix email in Documentation Boaz Harrosh - Fix broken email address MAINTAINERS: Change Boaz Harrosh's email
-
git://git.linaro.org/landing-teams/working/fujitsu/integration由 Linus Torvalds 提交于
Pull mailbox framework from Jassi Brar: "A framework for Mailbox controllers and clients have been cooking for more than a year now. Everybody in the CC list had been copied on patchset revisions and most of them have made sounds of approval, though just one concrete Reviewed-by. The patchset has also been in linux-next for a couple of weeks now and no conflict has been reported. The framework has the backing of at least 5 platforms, though I can't say if/when they upstream their drivers (some businesses have 'changed')" (Further acked-by by Arnd Bergmann and Suman Anna in the pull request thread) * 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration: dt: mailbox: add generic bindings doc: add documentation for mailbox framework mailbox: Introduce framework for mailbox mailbox: rename pl320-ipc specific mailbox.h
-
- 21 10月, 2014 27 次提交
-
-
git://www.linux-watchdog.org/linux-watchdog由 Linus Torvalds 提交于
Pull watchdog updates from Wim Van Sebroeck: - new Cadence WDT driver - new Ricoh RN5T618 watchdog - new DA9063 PMIC watchdog driver - new Meson WDT driver - add restart handling code - fixes and improvements * git://www.linux-watchdog.org/linux-watchdog: (25 commits) watchdog: meson: remove magic value for reboot watchdog: Let XILINX_WATCHDOG and TEGRA_WATCHDOG depend on HAS_IOMEM watchdog: sunxi: Add A31 watchdog support watchdog: sunxi: support parameterized compatible strings watchdog: imx2_wdt: add restart handler support watchdog: qcom: register a restart notifier watchdog: s3c2410: add restart handler watchdog: dw_wdt: add restart handler support ARM: defconfig: update multi_v7_defconfig ARM: meson: add watchdog driver ARM: docs: add documentation binding for meson watchdog stmp3xxx_rtc_wdt: Add suspend/resume PM support watchdog: Add DA9063 PMIC watchdog driver. watchdog: add driver for Ricoh RN5T618 watchdog watchdog: s3c2410_wdt: Add support for Watchdog device on Exynos7 watchdog: qcom: document device tree bindings watchdog: qcom: add support for KPSS WDT watchdog: dw_wdt: initialise TOP_INIT in dw_wdt_set_top() devicetree: Add Cadence WDT devicetree bindings documentation watchdog: Add Cadence WDT driver ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds由 Linus Torvalds 提交于
Pull LED update from Bryan Wu: "Basically we have some bug fixing and clean up and one big thing is we start to merge patch to add support LED Flash class" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: leds: gpio: cleanup the leds-gpio driver led: gpio: Fix possible ZERO_SIZE_PTR pointer dereferencing error. led: gpio: Sort include headers alphabetically leds: Improve and export led_update_brightness leds: trigger: gpio: fix warning in gpio trigger for gpios whose accessor function may sleep leds: lp3944: fix sparse warning leds: avoid using DEVICE_ATTR macro for max_brightness attribute leds: make brightness type consistent across whole subsystem leds: Reorder include directives
-
由 Linus Torvalds 提交于
Merge tag 'pwm/for-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm Pull pwm changes from Thierry Reding: "There are no new drivers here, only a couple of fixes all over the place" * tag 'pwm/for-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: pwm: Let PWM_CLPS711X depend on HAS_IOMEM pwm: atmel: Fix calculation of prescale value pwm: Fix uninitialized warnings in pwm_get() pwm: rockchip: Allow polarity invert on rk3288 pwm: imx: Avoid sample FIFO overflow for i.MX PWM version2 pwm: imx: Cleanup indentation for register definitions pwm: imx: Fix the macro MX3_PWMCR_PRESCALER(x) definition pwm: Fix possible ZERO_SIZE_PTR pointer dereferencing error. pwm: lpss: make it buildable only on X86 pwm: lpss: use c99 initializers in structures pwm: lpss: Fix build failure on PowerPC pwm: lpss: pci: Move to use pcim_enable_device() pwm: lpss: Properly split driver to parts pwm: lpss: Add ACPI and PCI IDs for Intel Braswell pwm: fsl-ftm: Select REGMAP_MMIO pwm: fsl-ftm: Document 'big-endian' property pwm: fsl-ftm: Convert to direct regmap API usage pwm: fsl-ftm: Clean up the code
-
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc由 Linus Torvalds 提交于
Pull ARC updates from Vineet Gupta: "Sorry for the late pull request. Current stuff was ready for a while but I was hoping to squeeze in support for almost ready ARC SDP platform (and avoid a 2nd pull request), however it seems there are still some loose ends which warrant more time. - Platform code reduction/moving-up (TB10X no longer needs any callbacks) - updated boot printing - kgdb update for arc gdb 7.5 - bug fixes (some marked for stable) - more code refactoring/consolidation" * tag 'arc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: ARC: boot: cpu feature print enhancements ARC: boot: consolidate cross-checking of h/w and s/w ARC: unbork FPU save/restore ARC: remove extraneous __KERNEL__ guards ARC: Update order of registers in KGDB to match GDB 7.5 ARC: Remove unneeded Kconfig entry NO_DMA ARC: BUG() dumps stack after @msg (@msg now same as in generic BUG)) ARC: refactoring: reduce the scope of some local vars ARC: remove gcc mpy heuristics ARC: RIP @running_on_hw ARC: Update comments about uncached address space ARC: rename kconfig option for unaligned emulation ARC: [nsimosci] Allow "headless" models to boot ARC: [arcfpga] Get rid of ARC_BOARD_ANGEL4 and ARC_BOARD_ML509 ARC: [arcfpga] Remove more dead code ARC: [plat*] move code out of .init_machine into common ARC: [arcfpga] consolidate machine description, DT ARC: Allow SMP kernel to build/boot on UP-only infrastructure
-
git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux由 Linus Torvalds 提交于
Pull more powerpc updates from Michael Ellerman: "Here's some more updates for powerpc for 3.18. They are a bit late I know, though must are actually bug fixes. In my defence I nearly cut the top of my finger off last weekend in a gruesome bike maintenance accident, so I spent a good part of the week waiting around for doctors. True story, I can send photos if you like :) Probably the most interesting fix is the sys_call_table one, which enables syscall tracing for powerpc. There's a fix for HMI handling for old firmware, more endian fixes for firmware interfaces, more EEH fixes, Anton fixed our routine that gets the current stack pointer, and a few other misc bits" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (22 commits) powerpc: Only do dynamic DMA zone limits on platforms that need it powerpc: sync pseries_le_defconfig with pseries_defconfig powerpc: Add printk levels to setup_system output powerpc/vphn: NUMA node code expects big-endian powerpc/msi: Use WARN_ON() in msi bitmap selftests powerpc/msi: Fix the msi bitmap alignment tests powerpc/eeh: Block CFG upon frozen Shiner adapter powerpc/eeh: Don't collect logs on PE with blocked config space powerpc/eeh: Block PCI config access upon frozen PE powerpc/pseries: Drop config requests in EEH accessors powerpc/powernv: Drop config requests in EEH accessors powerpc/eeh: Rename flag EEH_PE_RESET to EEH_PE_CFG_BLOCKED powerpc/eeh: Fix condition for isolated state powerpc/pseries: Make CPU hotplug path endian safe powerpc/pseries: Use dump_stack instead of show_stack powerpc: Rename __get_SP() to current_stack_pointer() powerpc: Reimplement __get_SP() as a function not a define powerpc/numa: Add ability to disable and debug topology updates powerpc/numa: check error return from proc_create powerpc/powernv: Fallback to old HMI handling behavior for old firmware ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux由 Linus Torvalds 提交于
Pull s390 updates from Martin Schwidefsky: "One patch to enable the BPF system call and three more bug fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/uprobes: fix kprobes dependency s390: wire up bpf syscall s390/mm: fixing calls of pte_unmap_unlock s390/hmcdrv: Restrict s390 HMC driver to S390 arch
-
由 Carlo Caione 提交于
This patch removes the magic value used for rebooting the board. This value is useless and leads to a static checker warning as reported by Dan Carpenter. Signed-off-by: NCarlo Caione <carlo@caione.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Chen Gang 提交于
They need HAS_IOMEM, so let them depend on it, the related error (with allmodconfig under um): MODPOST 1205 modules ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined! ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined! Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Chen-Yu Tsai 提交于
This patch adds support for the watchdog hardware found in A31 and newer SoCs. This new hardware has registers at different offsets, and the system reset control has been split out of the "mode" register into a new "configuration" register. Differences not supported by this driver include separate interrupt lines for each watchdog, instead of sharing an interrupt line and registers with the timer block. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Chen-Yu Tsai 提交于
This patch adds support for hardware parameters tied to compatible strings, so similar hardware can reuse the driver. This will be used to support the newer watchdog found in A31 and later SoCs. Differences in the new hardware include separate interrupt lines for each watchdog, and corresponding interrupt control/status registers. Watchdog control registers were also slightly rearranged. Also replace ioread32()/iowrite32() with readl()/writel() in various places changed. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Signed-off-by: NGuenter Roeck <linux@roeck-us.net> Acked-by: NHeiko Stuebner <heiko@sntech.de> Signed-off-by: NWim Van Sebroeck <wim@iguana.be> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
-
由 Jingchang Lu 提交于
Register the watchdog as the system restart function to the new introducing kernel restart call chain in the driver instead of providing the restart in machine desc. This restart handler function is from the mxc_restart() in arch/arm/mach-imx/system.c Signed-off-by: NJingchang Lu <jingchang.lu@freescale.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Josh Cartwright 提交于
The WDT's BITE_TIME warm-reset behavior can be leveraged as a last resort mechanism for triggering chip reset. Usually, other restart methods (such as PS_HOLD) are preferrable for issuing a more complete reset of the chip. As such, keep the priority of the watchdog notifier low. Signed-off-by: NJosh Cartwright <joshc@codeaurora.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Heiko Stuebner 提交于
On a lot of Samsung systems the watchdog is responsible for restarting the system and until now this code was contained in plat-samsung/watchdog-reset.c. With the introduction of the restart handlers, this code can now move into driver itself, removing the need for arch-specific code. Tested on a S3C2442 based GTA02 Signed-off-by: NHeiko Stuebner <heiko@sntech.de> Signed-off-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
-
由 Jisheng Zhang 提交于
The kernel core now provides an API to trigger a system restart. Register with it to support restarting the system via. watchdog. Signed-off-by: NJisheng Zhang <jszhang@marvell.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Carlo Caione 提交于
Update the multi_v7_defconfig enabling the watchdog driver for Meson SoCs. Signed-off-by: NCarlo Caione <carlo@caione.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Carlo Caione 提交于
This patch adds the watchdog driver for the Amlogic Meson SoCs used also to reboot the device. Signed-off-by: NCarlo Caione <carlo@caione.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Carlo Caione 提交于
Signed-off-by: NCarlo Caione <carlo@caione.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Janusz Uzycki 提交于
There is no conflict with rtc/rtc-stmp3xxx.c parent because modified registers in PM functions of stmp3xxx_rtc_wdt are different. Signed-off-by: NJanusz Uzycki <j.uzycki@elproma.com.pl> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Krystian Garbaciak 提交于
This driver supports the watchdog device inside the DA9063 PMIC. Signed-off-by: NKrystian Garbaciak <krystian.garbaciak@diasemi.com> Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de> Acked-by: NSteve Twiss <stwiss.opensource@diasemi.com> Tested-by: NSteve Twiss <stwiss.opensource@diasemi.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Beniamino Galvani 提交于
This adds a driver for the watchdog timer available in Ricoh RN5T618 PMIC. The device supports a programmable expiration time of 1, 8, 32 or 128 seconds. Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Naveen Krishna Chatradhi 提交于
Exynos7 SoC has a Watchdog for Atlas (A57) cores This patch adds support for the Atlas watchdog. Signed-off-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Josh Cartwright 提交于
The Qualcomm Krait Processor Sub-system (KPSS) contains one or more instances of the WDT. Provide documentation on how to describe these in the device tree. Signed-off-by: NJosh Cartwright <joshc@codeaurora.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Josh Cartwright 提交于
Add a driver for the watchdog timer block found in the Krait Processor Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064. Signed-off-by: NJosh Cartwright <joshc@codeaurora.org> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Jisheng Zhang 提交于
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register may be zero, so the timeout period may be very short after initialization is done, thus the system may be reset soon after enabling. We fix this problem by also initialising the TOP_INIT when setting TOP in function dw_wdt_set_top(). Signed-off-by: NJisheng Zhang <jszhang@marvell.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Harini Katakam 提交于
Add cadence-wdt bindings documentation. Signed-off-by: NHarini Katakam <harinik@xilinx.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Harini Katakam 提交于
Add Cadence WDT driver. This is used by Xilinx Zynq. Signed-off-by: NHarini Katakam <harinik@xilinx.com> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-K=C3=B6nig <u.kleine-koenig@pengutronix.de> Reviewed-by: NGuenter Roeck <linux@roeck-us.net> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-