Improves stability on affected devices and also fixes the Tx IQ calibration
related regression on some AR9340 devices such as the TP-Link TL-WDR4300.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl

This feature is still experimental.

The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.

The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For AR9550, program the synth value based on the ref. clock.
The logic for AR9550 is similar to AR9330, but keep the code
separate since changes for AR9330 are required - which would be
done later.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When AGC calibration is to be done, a GPM message with the
payload, MCI_GPM_WLAN_CAL_REQ has to be sent. Currently this falls
within the IQ-CAL code block which is incorrect. Fix this by using
a separate variable to decide when IQ-CAL is to be done separately
and call ar9003_mci_init_cal_req correctly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not enabled for any chip and is unused.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.

The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.

The patch contains no functional changes.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves parts of carl9170_update_beacon
into separate subroutines, so the parts become
more manageable.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit: "mac80211: introduce IEEE80211_NUM_TIDS and use it"
introduced a generic NUM_TID definitions for all everyone.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While the driver supports HW offload in a single
P2P client configuration, it doesn't support HW
offload in the concurrent P2P GO+CLIENT
configuration.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously, op_start would set disable_offload always
to false, even if it was set to true by the fw parser.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c

	/* Combinations with just one interface aren't real */
	if (WARN_ON(c->max_interfaces < 2))

Note: The number of supported interfaces is set by
the carl9170 firmware. The default number of
supported interfaces for all current firmwares is 2.
Therefore this warning can only be observed with
custom firmwares.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Janusz Dziedzic reported that after a change in wpa_supplicant
["nl80211: Automatically use concurrent P2P if possible"],
carl9170 was no longer able to host a P2P network.

This patch tackles the problem by allowing GO interfaces to be
registered, long after the P2P_CLIENT interface is brought up.
Reported-by: NJanusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Import new headers from my firmware branch:
<https://github.com/chunkeey/carl9170fw>

visit our wiki at:
<http://wireless.kernel.org/en/users/Drivers/carl9170.fw>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on a quick test [ath9k and carl9170],
TDLS seemed to be working fine. And while
we are at it, let's move the wiphy feature
flag set from carl9170_alloc into a single
place in carl9170_fw.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX aggregation is stopped, there are a few
different cases:
 - connection with the peer was dropped
 - session stop was requested locally
 - session stop was requested by the peer
 - connection was dropped while a session is stopping

The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.

Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.

In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to my recent commit (ath9k: allow to load EEPROM
content via firmware API) smatch complains about that
the 'pdata' variable in 'ath9k_hw_init' can be NULL
and it is dereferenced before checking that. That is
absolutely correct.

Check the 'pdata' variable before using it to avoid
a NULL pointer dereference.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is true for at least AR5213, and shouldn't be different for other
ath5k PHYs. Tested on AR2413 and AR5414.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Tested-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.

Tested with AR9271.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Accurate RX timestamp reporting is important for proper IBSS merging,
mesh synchronization, and MCCA scheduling. Namely, knowing where the TSF
is recorded is needed to sync with the beacon timestamp field.

Tested with AR9280.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_free_txskb() needs to be used instead of dev_kfree_skb_any for
tx packets passed to the driver from mac80211
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calibration data for devices w/o a separate
EEPROM chip can be specified via the 'eeprom_data'
field of 'ath9k_platform_data'. The 'eeprom_data'
is usually filled from board specific setup
functions. It is easy if the EEPROM data is mapped
to the memory, but it can be complicated if it is
stored elsewhere.

The patch adds support for loading of the EEPROM
data via the firmware API to avoid this limitation.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'ath9k_hw_nvram_read' function takes a
'struct ath_common *' as its first argument.
Almost each of its caller has a 'struct ath_hw *'
parameter in their argument list, and that is
dereferenced in order to get the 'struct ath_common'
pointer.

Change the first argument of 'ath9k_hw_nvram_read'
to be a 'struct ath_hw *', and remove the dereference
calls from the callers.

Also change the type of the first argument of the
ar9300_eeprom_read_{byte,word} functions.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Show the EEPROM offset of the failed read operation
in 'ath9k_hw_nvram_read'. The debug message is more
informative this way.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fill_eeprom functions are printing the same
debug message in case the 'ath9k_hw_nvram_read'
function fails. Remove the duplicated code from
fill_eeprom functions and add the ath_dbg call
directly into 'ath9k_hw_nvram_read'.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While AR_PHY_CCA_NOM_VAL_* does contain the expected internal noise floor
for a chip measured in clean air, it refers to the lowest expected reading.

Depending on the frequency, this measurement can vary by about 6db, thus
causing a higher reported channel noise and signal strength.

Factor in the 6db offset when converting internal noisefloor to channel noise.

This patch makes the reported values more accurate for all chips without
affecting NF calibration behavior.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Assign the training power for PAPRD based on the chip.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>