pxa25x platforms were left out of major ASoC Update patch.
Since f0fba2ad a registration of pxa-pcm-audio device is required for
ASoC to function on pxa platforms. Register one also for pxa210/pxa25x.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Since 2e48928d it's no longer possible to set
the name of the LED trigger for RFKILL events. Drop respective code from tosa-bt.c
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Reported-and-tested-by: NSven Neumann <s.neumann@raumfeld.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The use of wrong SD detect pin was introduced by this commit:

  ARM: pxa: Push Colibri evalboard MFP into module files

This fixes it.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Tested-by: NMarek Vasut <marek.vasut@gmail.com>

Build errors similar this appeared in todays kautobuild for the above
targets:

In file included from arch/arm/include/asm/pgtable.h:461,
                 from arch/arm/mach-pxa/generic.c:26:
include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type

None of the .c files including asm/pgtable.h with this error is using
this header, so simply remove the include.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>

Before this patch, the following error would sometimes occur after a
resume on pxa3xx:

    /path/to/mm/memory.c:144: bad pmd 8040542e.

The problem was that a temporary page table mapping was being improperly
restored.

The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort.  The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0.  This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: NMatt Reimer <mreimer@sdgsystems.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

As arch/arm/mach-pxa/eseries.c references w100fb_gpio_{read,write}()
directly.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush toggle_charger and sharpsl_bat works on suspend
instead.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>

Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ftrace requires sched_clock() to be notrace.  Ensure that all
implementations are so marked.  Also make sure that they include
linux/sched.h

Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NMikael Pettersson <mikpe@it.uu.se>
Tested-by: NEric Miao <eric.y.miao@gmail.com>
Tested-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In d7e81c26 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants.  Switch over to using this new interface.
Tested-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Tested on a Colibri Evaluation Board Rev.2.1 with a Colibri PXA310 module.
Signed-off-by: NBjorn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Rename colibri-pxa270-evalboard to colibri-evalboard as this board is used with
all Colibri modules.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.

(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Acked-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>

Saarb platform is a handheld platform that supports Marvell PXA955 silicon.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The core of PXA955 is PJ4. Add new PJ4 support. And add new macro
CONFIG_PXA95x.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Introduce 'struct clk' for memory and remove
get_memclk_frequency_10khz().
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Define all IRQs in irqs.h. If some IRQs are sharing one IRQ number, define
them together. If some IRQs are sharing same name with different IRQ number,
define different IRQ.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>