The CPLB implementations (mpu/nompu) had exact copies of the cacheinit
code.  Even the i/d cache functions are largely the same.  So unify them
both in the common kernel cache code.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The cycles clocksource is a higher resolution than the gptimer one, so
make sure the ratings field reflects this.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Commit 71e308a2 updated ftrace_push_return_trace() prototype but didn't
update the Blackfin ftrace code, so things broke.  Since we don't support
the new stuff yet, call it with stub values.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The cm-bf537u module, while similar to the cm-bf537e, is different enough
to warrant its own resources.  It has a USB controller but no PHY.
Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The default async timings are a little too fast for the parallel flash
that is attached by default to the async banks.  So slow things down a bit
so accessing the hardware is stable.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When doing XIP, we need to execute out of the async banks, so we need
ICPLBs to allow this.
Signed-off-by: NBernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Most messages are already using KERN_ALERT, so be consistent to make
things easier to check with test scripts.
Signed-off-by: NMingquan Pan <grace.pan@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF54x has three slave select signals for SPI0/SPI1, not eight.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The DTEST write bit is 2, not 1.  Improve comments in the related macro
while we're here.
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

For the adp5588 GPIO daughter card.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Make it easy to figure out if code changes here are correct.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Make sure our interrupt entry code with exact hardware errors handles
anomaly 05000283 (infinite stall in system MMR kill) so we don't stall
while under load.
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When preempt debugging is enabled, smp_processor_id() may utilize the
"current" structure.  This may not be safe to access under all exceptions
due to it being in dynamically allocated memory.  So in exception code,
make sure we use raw_smp_processor_id() instead to get at the real value
directly.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Not sure whether this has been reported/fixed before.

Today I built a Blackfin tool-chain from scratch for -tip testing,
and it triggers:

 arch/blackfin/kernel/vmlinux.lds:1238: undefined section `.data_a_l1' referenced in expression

and:

 arch/blackfin/kernel/vmlinux.lds:1238: undefined section `.text_data_l1'
referenced in expression

Now i dont have any way to test this linker script, but it now at
least builds fine after fixing what appears to be typos in those
assert statements.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The majority of the time we are returning to user space, it is not in the
fixed atomic code region.  So rather than branch to a function where we
check the PC and return, do the check inline and branch only when needed.

Also, tweak some of the fixed code handling based on assumptions we are
aware of but cannot be expressed in C.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The ASoC drivers have dropped the redundant "-spi" suffix in the driver
name, so update the board resources accordingly.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

No one uses these functions, and some are duplicate of existing C code.  So
just punt the whole thing.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Since the exception handler cannot cause exceptions, we cannot trace it
without easily causing double faults and crashing the system.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF522 and BF523 had their real max VCO values swapped.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We have an item to get this fixed, but in the mean time, disable selection
via Kconfig dependencies.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The handling of updating the [DI]MEM_CONTROL MMRs does not follow proper
sync procedures as laid out in the Blackfin programming manual.  So rather
than audit/fix every call location, create helper functions that do the
right things in order to safely update these MMRs.  Then convert all call
sites to use these new helper functions.

While we're fixing the code, drop the workaround for anomaly 05000125 as
that anomaly applies to old versions of silicon that we do not support.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Update the ad1836 resources for the new ASoC driver.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The board has some parallel flash hooked up to the async banks, so add
appropriate physmap resources for it.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Check whether index is within bounds before testing the element.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

I think we have to use the physical dimensions [mm] of the display for
.width and .heigth in struct bfin_bf54xfb_mach_info bf54x_lq043_data which
are copied to fbinfo->var.height/.width in bf54x-lq043fb.c.

linux/fb.h describes this values as 'height/weight of picture in mm'

Otherwise QT calcs the wrong dpi value and the displayed fonts are very
small.
Signed-off-by: NStefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The dm9000 driver expects two IORESOURCE_MEM to get at the device, so make
sure we declare things properly.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Latest smc91x driver allows you to specify settings in board resources
rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The interrupt probe workaround doesn't work without hacks to common code,
and the add-on card only needs a simple resistor to fix the problem, so
drop the board-specific hack.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Since the hardware only provides reporting for the last exception handled,
and the values are valid only when executing the exception handler, we
need to save the context for reporting at a later point.  While we do this
for one exception, it doesn't work properly when handling a second one as
the original exception is clobbered by the double fault.  So when double
fault debugging is enabled, create a dedicated shadow of these values and
save/restore out of there.  Now the crash report properly displays the
first exception as well as the second one.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

One too many zeros means we run way faster than the codec can handle.
Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values.  This means we would grant more access to mmap-ed pages than we
should have.  Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports.  This allows the LTP
mmap0{5,6,7} cases to run properly.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

I2C_BOARD_INFO() already sets .type, no need to set it again.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>