Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The amd-xgbe-phy driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The amd-xgbe driver needs to perform ioremap calls, so add HAS_IOMEM
to its build dependency.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to sync the states of the PCS and the PHY
after a reset is performed.  If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the spelling of the word "descriptor" in a couple
of locations.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for ethtool receive side scaling (RSS) commands.
Support is added to get/set the RSS hash key and the RSS lookup table.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides support for receive side scaling (RSS). RSS allows
for spreading incoming network packets across the Rx queues.  When used
in conjunction with the per DMA channel interrupt support, this allows
the receive processing to be spread across multiple processors.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device.  This allows for Tx and Rx
processing to run across multiple processsors.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide support for splitting IP packets so that the header and
payload can be sent to different DMA addresses.  This will allow
the IP header to be put into the linear part of the skb while the
payload can be added as frags.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use page allocations for Rx buffers instead of pre-allocating skbs
of a set size.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx and Rx descriptors are unsigned 32 bit values.  Use the u32
type, rather than unsigned int, to map these descriptors.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pre_xmit function name implies that it performs operations prior
to transmitting the packet when in fact it is responsible for setting
up the descriptors and initiating the transmit.  Rename this to
function from pre_xmit to dev_xmit, which is consistent with the name
used during receive processing - dev_read.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the channel and ring tracking structures allocation to device
open.  This will allow for future support to vary the number of Tx/Rx
queues without unloading the module.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This encapsulates all of the skb_copy_datagram_iovec() callers
with call argument signature "skb, offset, msghdr->msg_iov, length".

When we move to iov_iters in the networking, the iov_iter object will
sit in the msghdr.

Having a helper like this means there will be less places to touch
during that transformation.

Based upon descriptions and patch from Al Viro.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a very old and often unused option to configure
a bit in a register inside the DMA. This support should
not stay under Koption and should be extended for new chips too.
This will be do later maybe via device-tree parameters.
Also no performance impact when remove this setting on STi platforms.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the STMMAC_DEBUG_FS Koption is now removed from the
driver configuration and this support will be built
by default when DEBUG_FS is present. This can also be
useful on building driver verification.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes all the Koptions added to build the glue-logic files
for all different architectures: DWMAC_MESON, DWMAC_SUNXI, DWMAC_STI ...
Nowadays the stmmac needs to be compiled on several platforms; in some
case it very convenient to guarantee that its build is always completed
with success on all the branches where the driver is present.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a sysfs binary file is asked to be removed, it is found by
attribute name, so strictly speaking this change is not a fix, but
just in case when attribute name is changed in the driver or sysfs
internals are changed, it might be better to remove the previously
created file using right the same binary attribute.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this is check for dev is unnecessary, as we are already checking dev
after allocating it via alloc_netdev, and jumping to label: out
if it is NULL.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to issue CONFIG_DEV "get" firmware command.

This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.

The GET operation is allowed for VFs too.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Needed in order to get cache cold pages (L3 flushed) for HW scatter.

Otherwise memory may flush those entries when the packet comes from
PCI, causing back pressure resulting in BW decrease.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When IP_ALIGN has a non zero value, hardware will write to a non aligned
address. The only reader from this address is when copying the header
from the first frag into the linear buffer (further access to the IP
address will be from the linear buffer, in which the headers are
aligned). Since the penalty of non align access by the hardware is
greater than the software memcpy, changing the frag_align to always be 0.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to protect set_port_type() for concurrency, as the sysfs code could
call it from mutliple contexts in parallel.

The port_mutex is not enough because we need to protect from concurrent
modification of 'info' and stopping of the port sensing work.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.

This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.

Fixes: adbc7ac5 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a few problems with our parsing of the MDET registers:
* Queue IDs are longer than 8 bits
* Queue IDs are absolute for the device and the base queue must be
  subtracted out.
* VF IDs are longer than 8 bits
* Use the MASK define to mask the event value, instead of the SHIFT
  define.

Change-ID: I3dc7237f480c02e1192a2a8ea782f8a02ab2a8b7
Reported-by: NMarc Neustadter <marc.neustadter@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We must insert the VSI ID in the QTX_CTL register when
configuring queues for VMDQ VSIs.

Change-ID: Iedfe36bd42ca0adc90a7cc2b7cf04795a98f4761
Reported-by: NMarc Neustadter <marc.neustadter@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check the debug module parameter earlier to be able to catch the early
configuration phase adminq messages.

Change-ID: Ic84fabd72393489bbf96042de770790a80fd8468
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Tweak and homogenize the error reporting for get_lump() resource
tracking errors.

Change-ID: I11330161cc6ad8d04371c499c63071c816171c3b
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When there are more cores than vectors available to the PF, scale back
the LAN msix usage to force queue/vector sharing and leave some vectors
for Flow Director, VMDq, etc.

Change-ID: Ie0317732eb85ad8d851d7da7d9af86b1bf8c21ad
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The debugfs dump stats wasn't being kept up-to-date, was redundant with
the ethtool output, and didn't offer any useful additional info.  Rather
than continue trying to keep them aligned, just remove the debugfs command.

Change-ID: Id130ed9aef01c6369ab662c7b4c5ec5b1dbc5b40
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <Jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The call to irq_dynamic_disable was turning off the interrupt completely
when trying to set ITR to 0 (for lowest moderation).  Just remove the
call as setting the values to 0 later in this function will suffice.

Change-ID: I47caf1ecbe65653cf63ec833db93094cd83fd84d
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add 10G-Base-T support in i40evf.

Change-ID: I98a1c3138d7d6572fe7903a7c1c4692cae3260d5
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the interface is closed, but VFs exist, current code will spam all
the VFs with link messages every second. This is because the link event
code was looking at netif_carrier_ok() without checking to see if the
interface was actually open.

Refactor the logic to only check the carrier state if the interface is
actually open. This allows link changes to be reported correctly without
spamming the VFs.

Change-ID: If136e79bb3820d21ea4e39e332e8a9604efc2b2a
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When we receive an admin queue message, the msg_size field in the event
struct gets overwritten. Because of this, we need to reinit the field
each time we go through the loop. Without this we may receive truncated
messages due to the firmware thinking we have insufficient buffer size.

Change-ID: I21dcca5114d91365d731169965ce3ffec0e4a190
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When FD_SB/ATR are not enabled, do not allow flow director flush
and reinit.

Change-ID: Iafe261c1862992981615815551abd1ed9fada0a8
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NPatrick Lu <patrick.lu@intel.com>
Tested-by: <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reported-by: NMeelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work.  Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.

A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.

With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0d961b3b (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.

It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.

However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.

Putting the loop condition back in the switch mode section fixes it.

A comment has been added to point out the intent clearly to avoid future
confusion.  Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work.  Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.

A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.

With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0d961b3b (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.

It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.

However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.

Putting the loop condition back in the switch mode section fixes it.

A comment has been added to point out the intent clearly to avoid future
confusion.  Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>