This patch fixes decrementing SCO connection reference right after
stablishing the SCO connection with defer setup enabled. The dump below
shows a disconnection command with handle 0, the connection is still in
BT_CONNECT2 state and there isn't a handle associated with it.

< HCI Command: Accept Synchronous Connection (0x01|0x0029) plen 21
  bdaddr 78:47:1D:B3:72:6C
> HCI Event: Command Status (0x0f) plen 4
  Accept Synchronous Connection (0x01|0x0029) status 0x00 ncmd 1
< HCI Command: Disconnect (0x01|0x0006) plen 3
  handle 0 reason 0x13
  Reason: Remote User Terminated Connection
> HCI Event: Command Status (0x0f) plen 4
  Disconnect (0x01|0x0006) status 0x00 ncmd 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
  status 0x00 handle 46 bdaddr 78:47:1D:B3:72:6C
  type eSCO
  Air mode: CVSD
< SCO data: handle 46 flags 0x00 dlen 48
Signed-off-by: NClaudio Takahasi <claudio.takahasi@openbossa.org>
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

We use _get() and _put() for device ref-counting in the kernel. However,
hci_conn_put() is _not_ used for ref-counting, hence, rename it to
hci_conn_drop() so we can later fix ref-counting and introduce
hci_conn_put().

hci_conn_hold() and hci_conn_put() are currently used to manage how long a
connection should be held alive. When the last user drops the connection,
we spawn a delayed work that performs the disconnect. Obviously, this has
nothing to do with ref-counting for the _object_ but rather for the
keep-alive of the connection.

But we really _need_ proper ref-counting for the _object_ to allow
connection-users like rfcomm-tty, HIDP or others.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Trying to squeeze every single vendor setup routine into the same function
and have it assigned all the time is actually a bad idea. Especially since
the core can handle the absence of a setup routine perfectly fine.

To make this a lot simpler for future additions of vendor setup code,
split the BCM92035 setup into its own function and only assign it when
this specific device has been detected.

Doing it like this has the nice side benefit that we do not have to keep
a copy of the driver_info around.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

We need to verify that the given sockets actually are l2cap sockets. If
they aren't, we are not supposed to access bt_sk(sock) and we shouldn't
start the session if the offsets turn out to be valid local BT addresses.

That is, if someone passes a TCP socket to HIDCONNADD, then we access some
random offset in the TCP socket (which isn't even guaranteed to be valid).

Fix this by checking that the socket is an l2cap socket.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

We print this error twice in the first error-path so remove it. One error
message is enough.
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The driver init queue is no longer needed. This can be all handled
inside the drivers now. So remove it.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

With the early init stage during setup, this quirk can be simplified
and kept fully inside the driver.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some drivers require a special stage for their early init. This is
always specific to the driver or transport. So call back into driver to
allow bringing up the device.

The advantage with this stage is that the Bluetooth core is actually
handling the HCI layer now. This means that command and event processing
is available.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds a __hci_cmd_sync_ev function, analogous to
__hci_cmd_sync except that it also takes an event parameter to indicate
that the command completes with a special event instead of command
complete. Internally this new function takes advantage of the
hci_req_add_ev function introduced in the previous patch.

The primary expected user of this new function are the setup routines of
HCI drivers which may want to send custom commands and return only when
they have completed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for having commands within HCI requests that do
not result in a command complete but some other event. This is at least
needed for some vendor specific commands to be issued in the
hdev->setup() procecure, but might also be useful for other commands.

The way that the support is implemented is by extending the skb control
buffer to have a field to indicate that the command is expected to
terminate with a special event. After sending the command each received
event can then be compared against this field through hdev->sent_cmd.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a helper function for sending a single HCI command
waiting for its completion and then returning back the parameters in the
resulting command complete event (if there was one).

The implementation is very similar to that of hci_req_sync() except that
instead of invocing a callback for sending HCI commands the function
constructs and sends one itself and after being woken up picks the last
received event from hdev->recv_evt (if it matches the right criteria)
and returns it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds tracking of received HCI events to the hci_dev struct.
This is necessary so that a subsequent patch can implement a function
for sending a single command synchronously and returning the resulting
command complete parameters in the function return value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

This patch removes redundant whitespace from the HCI ldisc driver.
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds a NULL check for the HCI UART ldisc driver because some
of HCI UART drivers allow hci_uart_tty_receive function to be called
even though the HCI device hasn't been registered yet.
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds a check HCI_UART_REGISTERED before reading UART data in
the HCI UART H4 driver. UART data could arrive when inside the
hci_uart_tty_ioctl function after calling test_and_set_bit for
HCI_UART_PROTO_SET but before the hci_uart_set_proto function has
returned.

Backtrace:
[<c05f27ec>] (hci_recv_stream_fragment+0x0/0x74) from [<c04126f4>] (h4_recv+0x18/0x40)
 r7:eb1d4d1c r6:eb7683b0 r5:eae8e800 r4:0000000c
[<c04126dc>] (h4_recv+0x0/0x40) from [<c0411870>] (hci_uart_tty_receive+0x6c/0x94)
 r5:eae8e800 r4:eb768380
[<c0411804>] (hci_uart_tty_receive+0x0/0x94) from [<c027be88>] (flush_to_ldisc+0x16c/0x17c)
 r6:eae8e8d8 r5:eae8e800 r4:eae8e8c8
[<c027bd1c>] (flush_to_ldisc+0x0/0x17c) from [<c0050ae8>] (process_one_work+0x144/0x4d4)
[<c00509a4>] (process_one_work+0x0/0x4d4) from [<c0051208>] (worker_thread+0x180/0x370)
[<c0051088>] (worker_thread+0x0/0x370) from [<c005617c>] (kthread+0x90/0x9c)
[<c00560ec>] (kthread+0x0/0x9c) from [<c003a3a0>] (do_exit+0x0/0x7ec)
Signed-off-by: NChan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch removes the hci_req_cmd_status function since it is not
used anymore. The HCI request framework now considers the HCI command
has complete once the Command Status or Command Complete Event is
received.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since the HCI request framework was properly fixed, the hci_req_sync
call, in hci_inquiry, will return as soon as the HCI command completes
(not the Inquiry procedure). However, in inquiry ioctl implementation,
we want to sleep the user process until the inquiry procedure finishes.

This patch changes hci_inquiry so, in case the HCI Inquiry command
was executed successfully, it waits the HCI_INQUIRY flag to be cleared.
This way, the user process will sleep until the inquiry procedure
finishes.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some HCI commands don't send a Command Complete Event once the HCI
command has completed so they require some special handling from the
HCI request framework. These HCI commands, however, send a Command
Status Event to indicate that the command has been received, and
that the controller is currently performing the task for the command.

So, in order to properly handle those HCI commands, the HCI request
framework should consider the HCI command has completed once the
Command Status Event is received.

This way, we fix some issues regarding the Inquiry command support,
as well as add support for all those HCI commands which would require
some special handling from the HCI request framework.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Add support for the AR3012 chip.

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=03 Dev#= 21 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04d Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NNoguchi Kazutosi <linux@scaltinof.net>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The functions are moved in preparation of later patches.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length is not according specification so better fix it.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.

this commit will be squashed.
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When an interface is deleted make sure to cleanup all packet
buffers related to that interface.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware signalling functionality needs the credit map firmware
events. This patch adds registration of a handler for this event.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Firmware signalling needs to handle resources upon interface
events. This patch add calls in the interface event handling
routine.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>