When in analog mode, the RF connector will be created by
em28xx-video. However, when the device is in digital mode only,
the RF connector is not shown. In this case, let the DVB
core to create it for us.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add the needed bits to make em28xx to create a media
controller graph.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The Terratec Cinergy T XS is a DVB-T receiver with no analog TV tuner.
This patch adds support for the cards carrying the mt2060 tuner; it's
unclear whether there are cards sold under the same name which use a
different tuner.
As long as there are no reports of such cards, and indeed as long as
there are no working drivers for them, we assume that the USB device
[0ccd:0043] is carrying the mt2060 tuner.
Signed-off-by: NAlberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Devices that were using a8293 SEC are converted to I2C platform data
thus that old config structure is left unused.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Use I2C client binding for demod and SEC.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Load PCTV 460e tda10071 demod and a8293 SEC using I2C client bindings.
Remove old unused tda10071 config struct. We are using I2C platform
data now.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for DVB SEC (satellite equipment controller) I2C client.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.

As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Change ts2022 driver to ts2020 driver as ts2020 driver now supports
both models.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch will add basic support for the Elgato EyeTV Hybrid INT
2008 USB Stick.
Signed-off-by: NGilles Risch <gilles.risch@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Inspection shows that newlines are missing from several kernel messages
in em28xx-dvb.  Fix these.

Fixes: ca2b46da ("[media] em28xx-dvb: implement em28xx_ops: suspend/resume hooks")

Cc: <stable@vger.kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:

em28178 #0: Closing input extensionINFO: trying to register non-static key.

Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.

Fixes: aa929ad7 ("[media] em28xx: print a message at disconnect")

Cc: <stable@vger.kernel.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
	https://lkml.org/lkml/2014/7/11/794

I used it with those arguments:
	$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]

It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.

Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Terratec Cinergy T2 Stick HD [eb1a:8179] is a USB DVB-T/T2/C tuner that
contains following components:

* Empia EM28178 USB bridge
* Silicon Labs Si2168-A30 demodulator
* Silicon Labs Si2146-A10 tuner

I don't have the remote, so the RC_MAP is a best guess based on the pictures of
the remote controllers and other supported Terratec devices with a similar
remote.

[Antti: Resolved conflict caused by Leadtek VC100 patch]
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This field is not used on this driver anymore. Remove it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Used tda18212 tuner is implemented as a I2C driver. Use em28xx
tuner I2C client for tda18212 driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

TS mode must be set in the existing PCTV 292e driver.
Signed-off-by: NOlli Salonen <olli.salonen@iki.fi>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Implement set voltage operation.
Separate TS clock as a own configuration parameter.
Add TS clock polarity parameter.

[crope@iki.fi: merge em28xx driver m88ds3103 config change patch
to that one, in order to keep build unbroken]
Signed-off-by: NNibble Max <nibble.max@gmail.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Change em28xx_dvb_fini() to set fe exit flag to DVB_FE_DEVICE_REMOVED
when device is disconnected. em28xx maintains device disconnect status
in em28xx device. fe drivers will be able to now check the fe exit
status to avoid accessing the device, from their release interfaces
when called from disconnect path. This change depends on dvb-core
change that exports fe exit flag by moving it from fepriv to fe.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add error hanlding when EM2870_BOARD_KWORLD_A340 dvb_attach()
for fe and tuner fail in em28xx_dvb_init().
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

em28xx_dvb_resume() unregisters i2c tuner, i2c demod, and dvb.
This erroneous cleanup results in i2c tuner, i2c demod, and dvb
devices unregistered and removed during resume. This error is a
result of merge conflict between two patches that went into 3.15.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Modify all users of si2157_config to correctly initialize all not
listed values to 0.
Signed-off-by: NMatthias Schwarzott <zzam@gentoo.org>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

External LNA between antenna connector and RF tuner is controlled
by EM28178 GPIO 0. GPIO value 1 is LNA active and value 0 is LNA
disabled.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2157.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.

Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The first hunk of this patch got merged wrong, likely due to some
changes at the em28xx resume code. Revert it to reapply it right.

This reverts commit 37571b16.
Reported-by: NChris Lee <updatelee@gmail.com>
Reported-by: NHans Verkuil <hverkuil@xs4all.nl>
Cc: stable@vger.kernel.org # Don't apply this patch or 37571b16Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Pointer to device state has been moved to different location during
some change. PCTV 290e LNA function still uses old pointer, carried
over FE priv, and it crash.
Reported-by: NJanne Kujanpää <jikuja@iki.fi>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.

Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Cc: stable@vger.kernel.org
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Simplify the logic a little by removing one level of identation.
Also, it only makes sense to print something if the .fini callback
is actually doing something.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

We can't free struct em28xx while one of the extensions is still
using it.

So, add a kref() to control it, freeing it only after the
extensions fini calls.
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.

Tested with both 8VSB and 256QAM modulations.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add support for the Trident DRX-J driver, including a card profile for the
PCTV 80e which uses the chip.

Thanks to Trident for allowing the release of this code under a BSD license,
and of course Hauppauge/PCTV for pushing for its release to the community.

[pdickeybeta@gmail.com: modified to fix compilation errors and also to move
 the driver files from the drx39xy subdirectory to the frontends directory]

[m.chehab@samsung.com: fix merge conflicts, commented drx-j compilation and
 added EM28XX_R06_I2C_CLK setup also to the board setup]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That helps to understand what's going there.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Several URBs will be simply not filled. Don't call the DVB
core software filter for those empty URBs.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Implement em28xx_ops: suspend/resume hooks. em28xx usb driver will
invoke em28xx_ops: suspend and resume hooks for all its extensions
from its suspend() and resume() interfaces.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

Add missing m88ts2022 module reference counts as removing that module
is not allowed when it is used by em28xx-dvb module. That same module
was not unregistered correctly, fix it too.

Error cases validated by returning errors from m88ds3103, m88ts2022
and a8293 probe().
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The current code assumes that the analog + digital video endpoints are always at
interface number 0 when changing the alternate setting.
This seems to work fine for most existing devices.
However, at least the SpeedLink VAD Laplace webcam has the video endpoint on
interface number 3 (which fortunately doesn't cause any trouble because ist uses
bulk transfers only).
We already consider the actual interface number for audio endpoints, so
rename the the audio_ifnum variable and use it for all device types.
Also get get rid of a pointless (ifnum < 0) in em28xx-audio.
Signed-off-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

The option to load firmware asynchronously were added due to
a requirement with a few versions of udev. It turns that this was
a bad idea and caused regressions on drxk-based devices.

So, we end by only letting the firmware to be loaded syncronously
everywhere.

So, let's remove the bad code.

This patch partially reverts the changeset 8e30783b.
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>

That helps to identify if something fails and explain why em28xx
struct is not freed (if it ever happens).
Reviewed-by: NFrank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <m.chehab@samsung.com>