Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The phy_id property is deprecated and phy-handle has to be used instead.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:

"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."

And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482 ("wl18xx: wlan_irq: support platform
dependent interrupt types").

On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.

The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.

While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.

I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.

Let's change it for all omap boards with wlcore interrupt set as level.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

am335x-evm, am335x-evmsk and am335x-beaglebone are currently relying on
pinmux set by the bootloader to set the correct value for mmc1. Fix
this by adding pinmux data for the same in kernel.
Signed-off-by: NFaiz Abbas <faiz_abbas@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add clkctrl nodes for AM33xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.

This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

mmc2 used for wl12xx was missing the keep-power-in suspend
parameter. As a result the board couldn't reach suspend state.
Signed-off-by: NEyal Reizer <eyalr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add blue-and-red-wiring -property to lcdc node. The am335x-evmsk has
blue and red wires crossed to get 24-bit RGB (and 16-bit BGR)
support. After this patch am335x-evmsk supports BGR565, RGB888, and
XRGB8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Whitespace cleanup of lcdc related nodes. Do all indentation and
alignment with tabs instead of spaces.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for many boards:

"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for many boards:

"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for many boards:

"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that we are moving to OPPv2 bindings and able to add 1GHz OPP for
MPU, let's update the max MPU voltage range to align with the maximum
possible value allowed in the operating-points table, which is max
target voltage of 132500 uV + 2%.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.

This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use the pinmux IOPAD macro to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.

Also, use the mux defines instead of magic numbers for the padconf
values when defining the pinctrl lines to make it more readable.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per mmc device tree binding documentation card detect gpio has
to be active low signal. When a hardware is designed with active
high card detect, gpio polarity has to be changed with
cd-inverted dt property.

In AM335x the card detect gpio is designed as active low gpio.
So correcting the dt card detect gpio definition.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The section had two tabs instead of one.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

While Sitara AM335x SoCs are very close to OMAP SoCs, the 32-line GPIO
controllers are numbered from 0 on AM335x and from 1 on OMAP. But when
the configuration for the TI WLAN controllers was converted from
platform data to device tree, this detail was overlooked, as 10 boards
were using OMAP with the WL12xx and WL18xx controllers, and only one
was based on AM335x.

This invalid configuration prevents the WL1271 module on the AM335x
EVM-SK from notifying interrupts to the SoC, and breaks the wlan driver.

The DTS must be corrected to use the correct GPIO controller.
Signed-off-by: NRomain Izard <romain.izard.pro@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Acked-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
Tested-by: NTony Lindgren <tony@atomide.com>
Acked-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform.  Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.

For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown.  Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Acked-by: NWolfram Sang <wsa@sang-engineering.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses.  However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.

This patch corrects the references for the affected dts files.
Signed-off-by: NLeigh Brown <leigh@solinno.co.uk>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable DMA controller for USB
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the WiLink6 connected to mmc2.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable second USB channel and set it into 'host' mode.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
CC: <stable@vger.kernel.org> # 3.13.x
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add pinctrl section and cd-gpio to mmc1. Without these the SD card is not
working on EVM-SK board.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The clock for audio is sourced from virt_24000000_ck, so the correct
frequency is 24000000.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing nodes for the touchscreen available on AM335x EVM SK.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Do not reset GPIO0 at  boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.

Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>