Watching a light workload on Baytrail (running glxgears and a 1080p
decode), instead of the system remaining at low frequency, the glxgears
would regularly trigger waitboosting after which it would have to spend
a few seconds throttling back down. In this case, the waitboosting is
counter productive as the minimal wait for glxgears doesn't prevent it
from functioning correctly and delivering frames on time. In this case,
glxgears happens to almost always be waiting on the current request,
which we already expect to complete quickly (see i915_spin_request) and
so avoiding the waitboost on the active request and spinning instead
provides the best latency without overcommitting to upclocking.
However, if the system falls behind we still force the waitboost.
Similarly, we will also trigger upclocking if we detect the system is
not delivering frames on time - again using a mechanism that tries to
detect a miss and not preemptively upclock.

v2: Also skip boosting for after missed vblank if the desired request is
already active.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180118131609.16574-1-chris@chris-wilson.co.uk

The CDCLK bypass frequency can vary on upcoming platforms, so prepare
for that now by tracking its value in the CDCLK state.

Currently on BDW+ the bypass frequency is always the reference clock and
I didn't bother with earlier platforms since it's not all that clear
what's the bypass clock on those.

I also didn't bother adding support for changing this frequency, since
atm I don't see any need for it.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117172508.15993-1-imre.deak@intel.com

Since commit 4e773c3a ("drm/i915: Wire up shrinkctl->nr_scanned"),
we track the number of objects we scan and do not wish to exceed that as
it will overly penalise our own slabs under mempressure. Given that we
now know the target number of objects to scan, use that as our guide for
deciding to shrink as opposed to the number of objects we manage to
shrink (which doesn't correspond to the numbers we report to shrinkctl).

Fixes: 4e773c3a ("drm/i915: Wire up shrinkctl->nr_scanned")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115212455.24046-2-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

struct timeval is deprecated because it cannot represent times
past 2038. In this driver, the only use of this structure is
to capture debug information. This is easily changed to ktime_t,
which we then format as needed when printing it later.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117154916.219273-1-arnd@arndb.deSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>

When testing that the timeout fired, we need to be sure we have waited
just long enough for the timeout to have occurred and for the softirq
(on another cpu) to have completed. Sleeping for an arbitrary amount is
prone to error, so wait for the timeout instead and complain if it was
too late.

v2: Use wait_event_timeout to provide an upper bound
v3: Fix inverted check for wait_event_timeout timing out
v4: Restore the check that the fences aren't signalled too early, by
inspecting them before the expected timeout.

References: https://bugs.freedesktop.org/show_bug.cgi?id=104670Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117135713.2324-1-chris@chris-wilson.co.uk

It's perfectly legal to create a fb with stride < 512, and one of
the kms_plane_scaling subtests creates a very small fb.

Downgrade the WARN_ON to a simple check check, and because this
function is potentially called on every atomic update/pageflip,
downgrade the other WARN_ON to a WARN_ON_ONCE, and do the right
thing here.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180116155331.75175-1-maarten.lankhorst@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

intel_power_domains_init_hw() calls set_init_power, but when using
runtime power management this call is skipped. This prevents hw readout
from taking place.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104172
Link: https://patchwork.freedesktop.org/patch/msgid/20180116155324.75120-1-maarten.lankhorst@linux.intel.com
Fixes: bc87229f ("drm/i915/skl: enable PC9/10 power states during suspend-to-idle")
Cc: Nivedita Swaminathan <nivedita.swaminathan@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: NImre Deak <imre.deak@intel.com>

Tvrtko noticed that the comments describing the interaction of RCU and
the deferred worker for freeing drm_i915_gem_object were a little
confusing, so attempt to bring some sense to them.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115205759.13884-1-chris@chris-wilson.co.uk

Check that we can successfully wait upon a dma_fence using the
i915_sw_fence, including the optional timeout mechanism.

v2: Account for the rounding up of the timeout to the next second.
Unfortunately, the minimum delay is then 1 second.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115204348.8480-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

As freeing the objects require serialisation on struct_mutex, we should
prefer to use our singlethreaded driver wq that is dedicated to work
requiring struct_mutex (hence serialised).The benefit should be less
clutter on the system wq, allowing it to make progress even when the
driver/struct_mutex is heavily contended.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115122846.15193-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

In order to prevent a race condition where we may end up overaccounting
the active state and leaving the busy-stats believing the GPU is 100%
busy, lock out the tasklet while we reconstruct the busy state. There is
no direct spinlock guard for the execlists->port[], so we need to
utilise tasklet_disable() as a synchronous barrier to prevent it, the
only writer to execlists->port[], from running at the same time as the
enable.

Fixes: 4900727d ("drm/i915/pmu: Reconstruct active state on starting busy-stats")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115092041.13509-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

As the timeout mechanism has grown more and more complicated, using
multiple deferred tasks and more than doubling the size of our struct,
split the two implementations to streamline the simpler no-timeout
callback variant.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115090643.26696-2-chris@chris-wilson.co.uk

Without an accompanying timer (for internal fences), we can free the
fence callback immediately as we do not need to employ the RCU barrier
to serialise with the timer. By avoiding the RCU delay, we can avoid the
extra mempressure under heavy inter-engine request utilisation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115090643.26696-1-chris@chris-wilson.co.uk

DPCD read for the eDP is complete by the time intel_psr_init() is
called, which means we can avoid initializing PSR structures and state
if there is no sink support.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-3-dhinakaran.pandiyan@intel.com

The global variable dev_priv->psr.sink_support is set if an eDP sink
supports PSR. Use this instead of redoing the check with is_edp_psr().
Combine source and sink support checks into a macro that can be used to
return early from psr_{invalidate, single_frame_update, flush}.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-2-dhinakaran.pandiyan@intel.com

This flag has become redundant since
commit 4d90f2d5 ("drm/i915: Start tracking PSR state in crtc state")
It is set at the same place as psr.enabled, which is also exposed via
debugfs.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180103213824.1405-1-dhinakaran.pandiyan@intel.com

kcalloc is preffered for allocating arrays.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112170340.5387-2-tvrtko.ursulin@linux.intel.com

drivers/gpu/drm/i915/i915_pmu.c:795:34-40: ERROR: application of sizeof to pointer

 sizeof when applied to a pointer typed expression gives the size of
 the pointer

Generated by: scripts/coccinelle/misc/noderef.cocci

Fixes: 109ec558 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112170340.5387-1-tvrtko.ursulin@linux.intel.com

We have a hole in our busy-stat accounting if the pmu is enabled during
a long running batch, the pmu will not start accumulating busy-time
until the next context switch. This then fails tests that are only
sampling a single batch.

v2: Count each active port just once (context in/out events are only on
the first and last assignment to a port).
v3: Avoid hardcoding knowledge of 2 submission ports

Fixes: 30e17b78 ("drm/i915: Engine busy time tracking")
Testcase: igt/perf_pmu/busy-start
Testcase: igt/perf_pmu/busy-double-start
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111073031.14614-1-chris@chris-wilson.co.uk

As we kmalloc our dynamic sysfs attributes, we have to give them an
external static lock_class_key for them to use with lockdep.

Fixes: 109ec558 ("drm/i915/pmu: Only enumerate available counters in sysfs")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111140402.3984-1-chris@chris-wilson.co.uk

Switch over to dynamically creating device attributes, which are in turn
used by the perf core to expose available counters in sysfs.

This way we do not expose counters which are not avaiable on the current
platform, and are so more consistent between what we reply to open
attempts via the perf_event_open(2), and what is discoverable in sysfs.

v2:
 * Simplify attribute pointer freeing loop.
 * Changed attr init from macro to function.
 * More common error unwind. (Chris Wilson)
 * Rename some locals. (Chris Wilson)

v3:
 * Fixed double semi-colon. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111083525.32394-1-tvrtko.ursulin@linux.intel.com

With firmware 1.07 having fixed the state corruption issue, we can enable
the headless GT performance workaround for CNL as well. (Equivalent to
b6876374 ("drm/i915: Restore GT performance in headless mode with DMC
loaded") on other affected platforms.)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111082417.795-1-tvrtko.ursulin@linux.intel.com

This register does not contain it. Instead, we have to look into FAULT_TLB_DATA0 & 1
(where, by the way, we can also get the address space).

v2: Right formatting
v3:
  - Use 12 (as per the register format) instead of PAGE_SIZE (Chris)
  - s/BITS_44_TO_47/HIGHBITS (Chris)
  - Right formatting, this time for real

Fixes: b03ec3d6 ("drm/i915: There is only one fault register from GEN8 onwards")
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1513982329-32191-1-git-send-email-oscar.mateo@intel.comReviewed-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

While moving code around for solving lockdep issue for GuC log relay,
spotted that uc_fini_wq is not being called in failure path in gem_init.
Missed in the below commit. Add it.

v2: Removed GEM_BUG_ON(!HAS_GUC()) from intel_uc_fini_wq as init happens
only based on enable_guc module parameter and does not consider has_guc
capability. (Michal)
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Fixes: 3176ff49 ("drm/i915/guc: Move GuC workqueue allocations outside of the mutex")
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515588857-10283-1-git-send-email-sagar.a.kamble@intel.comSigned-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The power domain masks are 64 bit wide, so we need BIT_ULL() when
setting bits in them, these ones were missed during converting from 32
to 64 bit masks. All 3 enums are <32 atm, so this didn't cause a real
problem.

Fixes: d8fc70b7 ("drm/i915: Make power domain masks 64 bit long")
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109122040.19425-1-imre.deak@intel.com

The ACK/NACK implementation as found in e.g. the G965 has the falling
clock edge and the release of the data line after the ACK for the received
byte happen at the same time.

This is conformant with the I2C specification, which allows a zero hold
time, see footnote [3]: "A device must internally provide a hold time of
at least 300 ns for the SDA signal (with respect to the V IH(min) of the
SCL signal) to bridge the undefined region of the falling edge of SCL."

Some HDMI-to-VGA converters apparently fail to adhere to this requirement
and latch SDA at the falling clock edge, so instead of an ACK
sometimes a NACK is read and the slave (i.e. the EDID ROM) ends the
transfer.

The bitbanging releases the data line for the ACK only 1/4 bit time after
the falling clock edge, so a slave will see the correct value no matter
if it samples at the rising or the falling clock edge or in the center.

Fallback to bitbanging is already done for the CRT connector.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92685Signed-off-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a39f080b-81a5-4c93-b3f7-7cb0a58daca3@rwthex-w2-a.rwth-ad.de

When we retire a signaled fence, we free the dependency tree. However,
we skip clearing the list so that if we then try to adjust the priority
of the signaled fence, we may walk the list of freed dependencies.

[ 3083.156757] ==================================================================
[ 3083.156806] BUG: KASAN: use-after-free in execlists_schedule+0x199/0x660 [i915]
[ 3083.156810] Read of size 8 at addr ffff8806bf20f400 by task Xorg/831

[ 3083.156815] CPU: 0 PID: 831 Comm: Xorg Not tainted 4.15.0-rc6-no-psn+ #1
[ 3083.156817] Hardware name: Notebook                         N24_25BU/N24_25BU, BIOS 5.12 02/17/2017
[ 3083.156818] Call Trace:
[ 3083.156823]  dump_stack+0x5c/0x7a
[ 3083.156827]  print_address_description+0x6b/0x290
[ 3083.156830]  kasan_report+0x28f/0x380
[ 3083.156872]  ? execlists_schedule+0x199/0x660 [i915]
[ 3083.156914]  execlists_schedule+0x199/0x660 [i915]
[ 3083.156956]  ? intel_crtc_atomic_check+0x146/0x4e0 [i915]
[ 3083.156997]  ? execlists_submit_request+0xe0/0xe0 [i915]
[ 3083.157038]  ? i915_vma_misplaced.part.4+0x25/0xb0 [i915]
[ 3083.157079]  ? __i915_vma_do_pin+0x7c8/0xc80 [i915]
[ 3083.157121]  ? intel_atomic_state_alloc+0x44/0x60 [i915]
[ 3083.157130]  ? drm_atomic_helper_page_flip+0x3e/0xb0 [drm_kms_helper]
[ 3083.157145]  ? drm_mode_page_flip_ioctl+0x7d2/0x850 [drm]
[ 3083.157159]  ? drm_ioctl_kernel+0xa7/0xf0 [drm]
[ 3083.157172]  ? drm_ioctl+0x45b/0x560 [drm]
[ 3083.157211]  i915_gem_object_wait_priority+0x14c/0x2c0 [i915]
[ 3083.157251]  ? i915_gem_get_aperture_ioctl+0x150/0x150 [i915]
[ 3083.157290]  ? i915_vma_pin_fence+0x1d8/0x320 [i915]
[ 3083.157331]  ? intel_pin_and_fence_fb_obj+0x175/0x250 [i915]
[ 3083.157372]  ? intel_rotation_info_size+0x60/0x60 [i915]
[ 3083.157413]  ? intel_link_compute_m_n+0x80/0x80 [i915]
[ 3083.157428]  ? drm_dev_printk+0x1b0/0x1b0 [drm]
[ 3083.157443]  ? drm_dev_printk+0x1b0/0x1b0 [drm]
[ 3083.157485]  intel_prepare_plane_fb+0x2f8/0x5a0 [i915]
[ 3083.157527]  ? intel_crtc_get_vblank_counter+0x80/0x80 [i915]
[ 3083.157536]  drm_atomic_helper_prepare_planes+0xa0/0x1c0 [drm_kms_helper]
[ 3083.157587]  intel_atomic_commit+0x12e/0x4e0 [i915]
[ 3083.157605]  drm_atomic_helper_page_flip+0xa2/0xb0 [drm_kms_helper]
[ 3083.157621]  drm_mode_page_flip_ioctl+0x7d2/0x850 [drm]
[ 3083.157638]  ? drm_mode_cursor2_ioctl+0x10/0x10 [drm]
[ 3083.157652]  ? drm_lease_owner+0x1a/0x30 [drm]
[ 3083.157668]  ? drm_mode_cursor2_ioctl+0x10/0x10 [drm]
[ 3083.157681]  drm_ioctl_kernel+0xa7/0xf0 [drm]
[ 3083.157696]  drm_ioctl+0x45b/0x560 [drm]
[ 3083.157711]  ? drm_mode_cursor2_ioctl+0x10/0x10 [drm]
[ 3083.157725]  ? drm_getstats+0x20/0x20 [drm]
[ 3083.157729]  ? timerqueue_del+0x49/0x80
[ 3083.157732]  ? __remove_hrtimer+0x62/0xb0
[ 3083.157735]  ? hrtimer_try_to_cancel+0x173/0x210
[ 3083.157738]  do_vfs_ioctl+0x13b/0x880
[ 3083.157741]  ? ioctl_preallocate+0x140/0x140
[ 3083.157744]  ? _raw_spin_unlock_irq+0xe/0x30
[ 3083.157746]  ? do_setitimer+0x234/0x370
[ 3083.157750]  ? SyS_setitimer+0x19e/0x1b0
[ 3083.157752]  ? SyS_alarm+0x140/0x140
[ 3083.157755]  ? __rcu_read_unlock+0x66/0x80
[ 3083.157757]  ? __fget+0xc4/0x100
[ 3083.157760]  SyS_ioctl+0x74/0x80
[ 3083.157763]  entry_SYSCALL_64_fastpath+0x1a/0x7d
[ 3083.157765] RIP: 0033:0x7f6135d0c6a7
[ 3083.157767] RSP: 002b:00007fff01451888 EFLAGS: 00003246 ORIG_RAX: 0000000000000010
[ 3083.157769] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007f6135d0c6a7
[ 3083.157771] RDX: 00007fff01451950 RSI: 00000000c01864b0 RDI: 000000000000000c
[ 3083.157772] RBP: 00007f613076f600 R08: 0000000000000001 R09: 0000000000000000
[ 3083.157773] R10: 0000000000000060 R11: 0000000000003246 R12: 0000000000000000
[ 3083.157774] R13: 0000000000000060 R14: 000000000000001b R15: 0000000000000060

[ 3083.157779] Allocated by task 831:
[ 3083.157783]  kmem_cache_alloc+0xc0/0x200
[ 3083.157822]  i915_gem_request_await_dma_fence+0x2c4/0x5d0 [i915]
[ 3083.157861]  i915_gem_request_await_object+0x321/0x370 [i915]
[ 3083.157900]  i915_gem_do_execbuffer+0x1165/0x19c0 [i915]
[ 3083.157937]  i915_gem_execbuffer2+0x1ad/0x550 [i915]
[ 3083.157950]  drm_ioctl_kernel+0xa7/0xf0 [drm]
[ 3083.157962]  drm_ioctl+0x45b/0x560 [drm]
[ 3083.157964]  do_vfs_ioctl+0x13b/0x880
[ 3083.157966]  SyS_ioctl+0x74/0x80
[ 3083.157968]  entry_SYSCALL_64_fastpath+0x1a/0x7d

[ 3083.157971] Freed by task 831:
[ 3083.157973]  kmem_cache_free+0x77/0x220
[ 3083.158012]  i915_gem_request_retire+0x72c/0xa70 [i915]
[ 3083.158051]  i915_gem_request_alloc+0x1e9/0x8b0 [i915]
[ 3083.158089]  i915_gem_do_execbuffer+0xa96/0x19c0 [i915]
[ 3083.158127]  i915_gem_execbuffer2+0x1ad/0x550 [i915]
[ 3083.158140]  drm_ioctl_kernel+0xa7/0xf0 [drm]
[ 3083.158153]  drm_ioctl+0x45b/0x560 [drm]
[ 3083.158155]  do_vfs_ioctl+0x13b/0x880
[ 3083.158156]  SyS_ioctl+0x74/0x80
[ 3083.158158]  entry_SYSCALL_64_fastpath+0x1a/0x7d

[ 3083.158162] The buggy address belongs to the object at ffff8806bf20f400
                which belongs to the cache i915_dependency of size 64
[ 3083.158166] The buggy address is located 0 bytes inside of
                64-byte region [ffff8806bf20f400, ffff8806bf20f440)
[ 3083.158168] The buggy address belongs to the page:
[ 3083.158171] page:00000000d43decc4 count:1 mapcount:0 mapping:          (null) index:0x0
[ 3083.158174] flags: 0x17ffe0000000100(slab)
[ 3083.158179] raw: 017ffe0000000100 0000000000000000 0000000000000000 0000000180200020
[ 3083.158182] raw: ffffea001afc16c0 0000000500000005 ffff880731b881c0 0000000000000000
[ 3083.158184] page dumped because: kasan: bad access detected

[ 3083.158187] Memory state around the buggy address:
[ 3083.158190]  ffff8806bf20f300: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 3083.158192]  ffff8806bf20f380: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 3083.158195] >ffff8806bf20f400: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 3083.158196]                    ^
[ 3083.158199]  ffff8806bf20f480: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 3083.158201]  ffff8806bf20f500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 3083.158203] ==================================================================
Reported-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Reported-by: NMike Keehan <mike@keehan.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104436
Fixes: 1f181225 ("drm/i915/execlists: Keep request->priority for its lifetime")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: NAlexandru Chirvasitu <achirvasub@gmail.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180106105618.13532-1-chris@chris-wilson.co.uk

Geminilake requires the 3D driver to select whether barriers are
intended for compute shaders, or tessellation control shaders, by
whacking a "Barrier Mode" bit in SLICE_COMMON_ECO_CHICKEN1 when
switching pipelines.  Failure to do this properly can result in GPU
hangs.

Unfortunately, this means it needs to switch mid-batch, so only
userspace can properly set it.  To facilitate this, the kernel needs
to whitelist the register.

The workarounds page currently tags this as applying to Broxton only,
but that doesn't make sense.  The documentation for the register it
references says the bit userspace is supposed to toggle only exists on
Geminilake.  Empirically, the Mesa patch to toggle this bit appears to
fix intermittent GPU hangs in tessellation control shader barrier tests
on Geminilake; we haven't seen those hangs on Broxton.

v2: Mention WA #0862 in the comment (it doesn't have a name).
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180105085905.9298-1-kenneth@whitecape.org

There is a new version of DMC available for CNL.

The release notes mentions:
1. Fix for the issue where DC_STATE was getting enabled
even when disabled by driver causing data corruption

v2: Since the firmware is  merged to linux-firmware.git,
add MODULE_FIRMWARE.

v3: rebased. Correct commit message(Jani)

Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515109902-14076-1-git-send-email-anusha.srivatsa@intel.com

Since the firmwares are not yet released to public repo,
disable them on Geminilake.

v2: Remove the firmware versions (Michal)

v3: Remove unwanted defines (Rodrigo)
Correct commit message (Michal)

Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Fixes: 90f192c8 ("drm/i915/GuC/GLK: Load GuC on GLK")
Fixes: db5ba0d8 ("drm/i915/GLK/HuC: Load HuC on GLK")
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515006225-13003-1-git-send-email-anusha.srivatsa@intel.com

In some iommu, e.g. swiotlb, the available space can be quite limited.
So we employ a trial-and-error approach to seeing if our large
contiguous chunks can fit, and if that fails we try again with smaller
chunks after trying to free our own lazily allocated blobs. As we use a
trial-and-error approach, we do not want dma_map_sg() to emit a WARN of
its own accord, we want to gracefully report the error back to the caller
instead.

Note that our noisy culprit, swiotlb, doesn't honour the flag, yet.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180104163842.11635-1-chris@chris-wilson.co.uk

We should never insert the invalid seqno into the wait tree, so assert
we do not.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102192500.20364-1-chris@chris-wilson.co.uk

Instead of returning -EINVAL, GEM_BUG_ON when GuC reset is invoked for
platforms not supporting as we don't expect to invoke it.

v2: re-wording commit message and subject (Sagar)
Signed-off-by: NSujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1514928025-29659-2-git-send-email-sujaritha.sundaresan@intel.com

The Additional Data Struct (ADS) contains objects that are required by
GuC post FW load and are not necessarily submission-only. Even with
submission disabled we may require something inside the ADS, so it
makes more sense for them to be always created.

Similarly, we need to access GuC logs and even if GuC submission
is disabled, to debug issues with GuC loading or with whatever we're using
GuC for.

v2: re-wording commit message (Sagar)
Signed-off-by: NSujaritha Sundaresan <sujaritha.sundaresan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1514928025-29659-1-git-send-email-sujaritha.sundaresan@intel.com

After staring at the list_for_each_safe macros for a bit, our current
invocation of list_safe_reset_next in execlists_schedule() simply
reduces to list_for_each.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-11-chris@chris-wilson.co.uk

The dependency chain must be an acyclic graph. This is checked by the
swfence, but for sanity, also do a simple check that we do not corrupt
our list iteration in execlists_schedule() by a shallow dependency
cycle.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-10-chris@chris-wilson.co.uk

Back up our comment that all signalers should have been signaled before
we ourselves were retired with an assert to that effect.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-9-chris@chris-wilson.co.uk

To modify the global seqno may require rewriting a few registers, which
requires us to hold the rpm wakeref. We must therefore take it around
the call to i915_gem_set_global_seqno() in debugfs, on behalf of the
user.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-15-chris@chris-wilson.co.uk

Move the register settings for enabling execlists into its own function
for clarity.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-18-chris@chris-wilson.co.uk

Currently, we record the elsp register offset inside init-hw but we only
need to do it once during engine setup (after we know the mmio
iomapping).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102151235.3949-17-chris@chris-wilson.co.uk