Signed-off-by: NArvid Brodin <arvid.brodin@alten.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements the rtnl_link_ops fill_info routine for HSR.
Signed-off-by: NArvid Brodin <arvid.brodin@alten.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.

This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.

At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no need to unregister the multicast group if the
generic netlink family is registered immediately after.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.

The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If 'hsr_get_node_data()' returns error, going directly to 'fail' label
doesn't free the memory pointed by 'skb_out'.
Signed-off-by: NGeyslan G. Bem <geyslan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:

@@
identifier ops;
@@
+const
 struct genl_ops ops[] = {
 ...
 };

(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This simplifies the code since there's no longer a
need to have error handling in the registration.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

High-availability Seamless Redundancy ("HSR") provides instant failover
redundancy for Ethernet networks. It requires a special network topology where
all nodes are connected in a ring (each node having two physical network
interfaces). It is suited for applications that demand high availability and
very short reaction time.

HSR acts on the Ethernet layer, using a registered Ethernet protocol type to
send special HSR frames in both directions over the ring. The driver creates
virtual network interfaces that can be used just like any ordinary Linux
network interface, for IP/TCP/UDP traffic etc. All nodes in the network ring
must be HSR capable.

This code is a "best effort" to comply with the HSR standard as described in
IEC 62439-3:2010 (HSRv0).
Signed-off-by: NArvid Brodin <arvid.brodin@xdin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>