By default Flow Control feature is not being enabled in stmmac.

This is a useful feature that can prevent loss of packets and now that
XGMAC already supports it (along with GMAC and QoS) it makes sense to
activate it.

Switch the module parameter to FLOW_AUTO so that Flow Control is
activated.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Finish the implementation of Flow Control feature. In order for it to
work correctly we need to set EHFC bit and the correct threshold values
for activating and deactivating it.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ioana Ciocoi Radulescu says:

====================
dpaa2-eth: Add flow steering support without masking

On DPAA2 platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't offer
flow steering capabilities at all on these platforms.

Introduce a limited support for flow steering, where we only
allow ethtool rules that share a common key (i.e. have the same
header fields). If a rule with a new composition key is wanted,
the user must first manually delete all previous rules.

First patch fixes a minor bug, the next two cleanup and prepare
the code and the last one introduces the actual FS support.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.

We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.

When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.

Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two macros to simplify reading DPNI options.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the Rx flow classification enable flag only if key config
operation is successful.

Fixes 3f9b5c9 ("dpaa2-eth: Configure Rx flow classification key")
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.

Remove the warning by adding a fall through comment.

Fixes: 1c6952ca ("nfp: flower: generate merge flow rule")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.

This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
bnx2x: Support for timestamping in P2P mode.

The patch series adds driver support for timestamping the ptp packets
in peer-delay (P2P) mode.
 - Patch (1) performs the code cleanup.
 - Patch (2) adds the required implementation.

Please consider applying it 'net-next' tree.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
  NIG_REG_P0/1_LLH_PTP_PARAM_MASK
  NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
    bit 1 - IPv4 DA 1 of 224.0.0.107.
    bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
    bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
  NIG_REG_P0/1_LLH_PTP_RULE_MASK
  NIG_REG_P0/1_TLLH_PTP_RULE_MASK
    bit 2 - {IPv4 DA 1; UDP DP 0}
    bit 6 - MAC Ethertype 0 of 0x88F7.
    bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/xen-netfront.c: In function ‘netback_changed’:
drivers/net/xen-netfront.c:2038:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (dev->state == XenbusStateClosed)
      ^
drivers/net/xen-netfront.c:2041:2: note: here
  case XenbusStateClosing:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Murali Karicheri says:

====================
net: hsr: updates from internal tree

This series picks commit from our internal kernel tree.
Patch 1/3 fixes a file name issue introduced in my previous
series.

History:
  v2: fixed patch 3/3 by moving stats update to inside hsr_forward_skb()
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add tx stats to hsr interface. Without this
ifconfig for hsr interface doesn't show tx packet stats.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the path of hsr debugfs root directory to use the net device
name so that it can work with multiple interfaces. While at it,
also fix some typos.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the file name and functions to match with existing implementation.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.

I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.

v2:
- make the feature constant a comment so that readers know which
  features are supported by the respective PHY
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: Flower flow merging

John Hurley says,

These patches deal with 'implicit recirculation' on the NFP. This is a
firmware feature whereby a packet egresses to an 'internal' port meaning
that it will recirculate back to the header extract phase with the
'internal' port now marked as its ingress port. This internal port can
then be matched on by another rule. This process simulates how OvS
datapath outputs to an internal port. The FW traces the packet's
recirculation route and sends a 'merge hint' to the driver telling it
which flows it matched against. The driver can then decide if these flows
can be merged to a single rule and offloaded.

The patches deal with the following issues:

- assigning/freeing IDs to/from each of these new internal ports
- offloading rules that match on internal ports
- offloading neighbour table entries whose egress port is internal
- handling fallback traffic with an internal port as ingress
- using merge hints to create 'faster path' flows and tracking stats etc.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A merge flow is formed from 2 sub flows. The match fields of the merge are
the same as the first sub flow that has formed it, with the actions being
a combination of the first and second sub flow. Therefore, a merge flow
should replace sub flow 1 when offloaded.

Offload valid merge flows by using a new 'flow mod' message type to
replace an existing offloaded rule. Track the deletion of sub flows that
are linked to a merge flow and revert offloaded merge rules if required.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the merging of 2 sub flows, a new 'merge' flow will be created and
written to FW. The TC layer is unaware that the merge flow exists and will
request stats from the sub flows. Conversely, the FW treats a merge rule
the same as any other rule and sends stats updates to the NFP driver.

Add links between merge flows and their sub flows. Use these links to pass
merge flow stats updates from FW to the underlying sub flows, ensuring TC
stats requests are handled correctly. The updating of sub flow stats is
done on (the less time critcal) TC stats requests rather than on FW stats
update.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When combining 2 sub_flows to a single 'merge flow' (assuming the merge is
valid), the merge flow should contain the same match fields as sub_flow 1
with actions derived from a combination of sub_flows 1 and 2. This action
list should have all actions from sub_flow 1 with the exception of the
output action that triggered the 'implicit recirculation' by sending to
an internal port, followed by all actions of sub_flow 2. Any pre-actions
in either sub_flow should feature at the start of the action list.

Add code to generate a new merge flow and populate the match and actions
fields based on the sub_flows. The offloading of the flow is left to
future patches.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two flows can be merged if the second flow (after recirculation) matches
on bits that are either matched on or explicitly set by the first flow.
This means that if a packet hits flow 1 and recirculates then it is
guaranteed to hit flow 2.

Add a 'can_merge' function that determines if 2 sub_flows in a merge hint
can be validly merged to a single flow.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a merge hint is received containing 2 flows that are matched via an
implicit recirculation (sending to and matching on an internal port), fw
reports that the flows (called sub_flows) may be able to be combined to a
single flow.

Add infastructure to accept and process merge hint messages. The actual
merging of the flows is left as a stub call.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each flow is given a context ID that the fw uses (along with its cookie)
to identity the flow. The flows stats are updated by the fw via this ID
which is a reference to a pre-allocated array entry.

In preparation for flow merge code, enable the nfp_fl_payload structure to
be accessed via this stats context ID. Rather than increasing the memory
requirements of the pre-allocated array, add a new rhashtable to associate
each active stats context ID with its rule payload.

While adding new code to the compile metadata functions, slightly
restructure the existing function to allow for cleaner, easier to read
error handling.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The neighbour table in the FW only accepts next hop entries if the egress
port is an nfp repr. Modify this to allow the next hop to be an internal
port. This means that if a packet is to egress to that port, it will
recirculate back into the system with the internal port becoming its
ingress port.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW may receive a packet with its ingress port marked as an internal port.
If a rule does not exist to match on this port, the packet will be sent to
the NFP driver. Modify the flower app to detect packets from such internal
ports and convert the ingress port to the correct kernel space netdev.

At this point, it is assumed that fallback packets from internal ports are
to be sent out said port. Therefore, set the redir_egress bool to true on
detection of these ports.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, it is assumed that fallback packets will be from reprs. Modify
this to allow an app to receive non-repr ports from the fallback channel -
e.g. from an internal port. If such a packet is received, do not update
repr stats.

Change the naming function calls so as not to imply it will always be a
repr netdev returned. Add the option to set a bool value to redirect a
fallback packet out the returned port rather than RXing it. Setting of
this bool in subsequent patches allows the handling of packets falling
back when they are due to egress an internal port.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent FW modifications allow the offloading of non repr ports. These
ports exist internally on the NFP. So if a rule outputs to an 'internal'
port, then the packet will recirculate back into the system but will now
have this internal port as it's incoming port. These ports are indicated
by a specific type field combined with an 8 bit port id.

Add private app data to assign additional port ids for use in offloads.
Provide functions to lookup or create new ids when a rule attempts to
match on an internal netdev - the only internal netdevs currently
supported are of type openvswitch. Have a netdev notifier to release
port ids on netdev unregister.

OvS offloads rules that match on internal ports as TC egress filters.
Ensure that such rules are accepted by the driver.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Write to a FW symbol to indicate that the driver supports flow merging. If
this symbol does not exist then flow merging and recirculation is not
supported on the FW. If support is available, add a stub to deal with FW
to kernel merge hint messages.

Full flow merging requires the firmware to support of flow mods. If it
does not, then do not attempt to 'turn on' flow merging.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: fixes sparse: warning and type error

This patchset fixes a sparse warning and a overflow problem.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting vport->bw_limit to hdev->tm_info.pg_info[0].bw_limit
in hclge_tm_vport_tc_info_update, vport->bw_limit can be as big as
HCLGE_ETHER_MAX_RATE (100000), which can not fit into u16 (65535).

So this patch fixes it by using u32 for vport->bw_limit.

Fixes: 84844054 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The input parameter "proto" in function hclge_set_vlan_filter_hw()
is asked to be __be16, but got u16 when calling it in function
hclge_update_port_base_vlan_cfg().

This patch fixes it by converting it with htons().
Reported-by: Nkbuild test robot <lkp@intel.com>
Fixes: 21e043cd ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: fully support memory accounting

sctp memory accounting is added in this patchset by using
these kernel APIs on send side:

  - sk_mem_charge()
  - sk_mem_uncharge()
  - sk_wmem_schedule()
  - sk_under_memory_pressure()
  - sk_mem_reclaim()

and these on receive side:

  - sk_mem_charge()
  - sk_mem_uncharge()
  - sk_rmem_schedule()
  - sk_under_memory_pressure()
  - sk_mem_reclaim()

With sctp memory accounting, we can limit the memory allocation by
either sysctl:

  # sysctl -w net.sctp.sctp_mem="10 20 50"

or cgroup:

  # echo $((8<<14)) > \
    /sys/fs/cgroup/memory/sctp_mem/memory.kmem.tcp.limit_in_bytes

When the socket is under memory pressure, the send side will block
and wait, while the receive side will renege or drop.

v1->v2:
  - add the missing Reported/Tested/Acked/-bys.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_forward_alloc's updating is also done on rx path, but to be consistent
we change to use sk_mem_charge() in sctp_skb_set_owner_r().

In sctp_eat_data(), it's not enough to check sctp_memory_pressure only,
which doesn't work for mem_cgroup_sockets_enabled, so we change to use
sk_under_memory_pressure().

When it's under memory pressure, sk_mem_reclaim() and sk_rmem_schedule()
should be called on both RENEGE or CHUNK DELIVERY path exit the memory
pressure status as soon as possible.

Note that sk_rmem_schedule() is using datalen to make things easy there.
Reported-by: NMatteo Croce <mcroce@redhat.com>
Tested-by: NMatteo Croce <mcroce@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now when sending packets, sk_mem_charge() and sk_mem_uncharge() have been
used to set sk_forward_alloc. We just need to call sk_wmem_schedule() to
check if the allocated should be raised, and call sk_mem_reclaim() to
check if the allocated should be reduced when it's under memory pressure.

If sk_wmem_schedule() returns false, which means no memory is allowed to
allocate, it will block and wait for memory to become available.

Note different from tcp, sctp wait_for_buf happens before allocating any
skb, so memory accounting check is done with the whole msg_len before it
too.
Reported-by: NMatteo Croce <mcroce@redhat.com>
Tested-by: NMatteo Croce <mcroce@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add neighbour offload indication

Neighbour entries are programmed to the device's table so that the
correct destination MAC will be specified in a packet after it was
routed.

Despite being programmed to the device and unlike routes and FDB
entries, neighbour entries are currently not marked as offloaded. This
patchset changes that.

Patch #1 is a preparatory patch to make sure we only mark a neighbour as
offloaded in case it was successfully programmed to the device.

Patch #2 sets the offload indication on neighbours.

Patch #3 adds a test to verify above mentioned functionality.

Patched iproute2 version that prints the offload indication is available
here [1].

[1] https://github.com/idosch/iproute2/tree/idosch-next
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that neighbour entries are marked as offloaded.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to routes and FDB entries, the neighbour table is
reflected to the device.

Set an offload indication on the neighbour in case it was programmed to
the device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Next patch will add offload indication to neighbours, but the indication
should only be altered in case the neighbour was successfully added to /
deleted from the device.

Propagate neighbour update errors, so that they could be taken into
account by the next patch.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>