Externally learned entries are similar to PERMANENT entries in the
sense they are managed by userspace and can not be garbage collected.
As such remove them from the gc_list, remove the flags check from
neigh_forced_gc and skip threshold checks in neigh_alloc. As with
PERMANENT entries, this allows unlimited number of NTF_EXT_LEARNED
entries.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

neigh_update_ext_learned has one caller in neighbour.c so does not need
to be defined in the header. Move it and in the process remove the
intialization of ndm_flags and just set it based on the flags check.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

neigh_del now only has 1 caller, and the state and flags arguments
are both 0. Remove them and simplify neigh_del.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PERMANENT entries are not on the gc_list so the state check is now
redundant. Also, the move to not purge entries until after 5 seconds
should not apply to FAILED entries; those can be removed immediately
to make way for newer ones. This restores the previous logic prior to
the gc_list.

Fixes: 58956317 ("neighbor: Improve garbage collection")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lock checker noted an inverted lock order between neigh_change_state
(neighbor lock then table lock) and neigh_periodic_work (table lock and
then neighbor lock) resulting in:

[  121.057652] ======================================================
[  121.058740] WARNING: possible circular locking dependency detected
[  121.059861] 4.20.0-rc6+ #43 Not tainted
[  121.060546] ------------------------------------------------------
[  121.061630] kworker/0:2/65 is trying to acquire lock:
[  121.062519] (____ptrval____) (&n->lock){++--}, at: neigh_periodic_work+0x237/0x324
[  121.063894]
[  121.063894] but task is already holding lock:
[  121.064920] (____ptrval____) (&tbl->lock){+.-.}, at: neigh_periodic_work+0x194/0x324
[  121.066274]
[  121.066274] which lock already depends on the new lock.
[  121.066274]
[  121.067693]
[  121.067693] the existing dependency chain (in reverse order) is:
...

Fix by renaming neigh_change_state to neigh_update_gc_list, changing
it to only manage whether an entry should be on the gc_list and taking
locks in the same order as neigh_periodic_work. Invoke at the end of
neigh_update only if diff between old or new states has the PERMANENT
flag set.

Fixes: 8cc196d6 ("neighbor: gc_list changes should be protected by table lock")
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 69bd4840 ("net/sched: Remove egdev mechanism"),
tc_setup_cb_call() is nearly identical to tcf_block_cb_call(),
so we can just fold tcf_block_cb_call() into tc_setup_cb_call()
and remove its unused parameter 'exts'.

Fixes: 69bd4840 ("net/sched: Remove egdev mechanism")
Cc: Oz Shlomo <ozsh@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NOz Shlomo <ozsh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was checking for non-NULL address.
- adapter->napi[i]

This is pointless as these will be always non-NULL, since the
'dapter->napi' is allocated in init_napi().
It is safe to get rid of useless checks for addresses to fix the
coccinelle warning:
>>drivers/net/ethernet/ibm/ibmvnic.c: test of a variable/field address
Since such statements always return true, they are redundant.
Signed-off-by: NWen Yang <wen.yang99@zte.com.cn>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Thomas Falcon <tlfalcon@linux.ibm.com>
CC: John Allen <jallen@linux.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linuxppc-dev@lists.ozlabs.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tun_xdp_one() runs with local bh disabled. So there is no need to
disable preemption by calling get_cpu_ptr while updating stats. This
patch replaces the use of get_cpu_ptr() with this_cpu_ptr() as a
micro-optimization. Also removes related put_cpu_ptr call.
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ppp and hamradio have copies of the same code that uses a semaphore
in place of a completion for historic reasons. Make it use the
proper interface instead in all copies.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now get a link failure when CONFIG_INET is disabled, since
tcp_gro_complete is unavailable:

drivers/net/ethernet/hisilicon/hns3/hns3_enet.o: In function `hns3_set_gro_param':
hns3_enet.c:(.text+0x230c): undefined reference to `tcp_gro_complete'

Add an explicit CONFIG_INET dependency here to avoid the broken
configuration.

Fixes: a6d53b97 ("net: hns3: Adds GRO params to SKB for the stack")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Petr Machata says:

====================
Introduce NETDEV_PRE_CHANGEADDR

Spectrum devices have a limitation that all router interfaces need to
have the same address prefix. In Spectrum-1, the requirement is for the
initial 38 bits of all RIFs to be the same, in Spectrum-2 the limit is
36 bits. Currently violations of this requirement are not diagnosed. At
the same time, if the condition is not upheld, the mismatched MAC
address ends up overwriting the common prefix, and all RIF MAC addresses
silently change to the new prefix.

It is therefore desirable to be able at least to diagnose the issue, and
better to reject attempts to change MAC addresses in ways that is
incompatible with the device.

Currently MAC address changes are notified through emission of
NETDEV_CHANGEADDR, which is done after the change. Extending this
message to allow vetoing is certainly possible, but several other
notification types have instead adopted a simple two-stage approach:
first a "pre" notification is sent to make sure all interested parties
are OK with the change that's about to be done. Then the change is done,
and afterwards a "post" notification is sent.

This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore this patchset introduces it for NETDEV_CHANGEADDR as well.

One prominent path to emitting NETDEV_CHANGEADDR is through
dev_set_mac_address(). Therefore in patch #1, give this function an
extack argument, so that a textual reason for rejection (or a warning)
can be communicated back to the user.

In patch #2, add the new notification type. In patch #3, have dev.c emit
the notification for instances of dev_addr change, or addition of an
address to dev_addrs list.

In patches #4 and #5, extend the bridge driver to handle and emit the
new notifier.

In patch #6, change IPVLAN to emit the new notifier.

Likewise for bonding driver in patches #7 and #8. Note that the team
driver doesn't need this treatment, as it goes through
dev_set_mac_address().

In patches #9, #10 and #11 adapt mlxsw to veto MAC addresses on router
interfaces, if they violate the requirement that all RIF MAC addresses
have the same prefix.

Finally in patches #12 and #13, add a test for vetoing of a direct
change of a port device MAC, and indirect change of a bridge MAC.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a FID RIF is created for a bridge with IP address, its MAC address
must obey the same requirements as other RIFs. Test that attempts to
change the address incompatibly by attaching a device are vetoed with
extack.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that attempts to change address in a way that violates Spectrum
requirements are vetoed with extack.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On NETDEV_PRE_CHANGEADDR, if the change is related to a RIF interface,
verify that it satisfies the criterion that all RIF interfaces have the
same MAC address prefix, as indicated by mlxsw_sp.mac_mask.

Additionally, besides explicit address changes, check that the address
of an interface for which a RIF is about to be added matches the
required pattern as well.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Spectrum hardware demands that all router interfaces in the system
have the same first 38 resp. 36 bits of MAC address: the former limit
holds on Spectrum, the latter on Spectrum-2. Add a field that refers to
the required prefix mask and initialize in mlxsw_sp1_init() and
mlxsw_sp2_init().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare mlxsw_sp_netdevice_router_port_event() for handling of
NETDEV_PRE_CHANGEADDR. Split out the part that deals with the actual
changes and call it for the two events currently handled.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Give interested parties an opportunity to veto an impending HW address
change.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before NETDEV_CHANGEADDR, bond driver should emit NETDEV_PRE_CHANGEADDR,
and allow consumers to veto the address change. To propagate further the
return code from NETDEV_PRE_CHANGEADDR, give the function that
implements address change a return value.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A NETDEV_CHANGEADDR event implies a change of address of each of the
IPVLANs of this IPVLAN device. Therefore propagate NETDEV_PRE_CHANGEADDR
to all the IPVLANs.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.

Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.

This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.

To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5e-updates-2018-12-11

From Eli Britstein,
Patches 1-10 adds remote mirroring support.
Patches 1-4 refactor encap related code as pre-steps for using per
destination encapsulation properties.
Patches 5-7 use extended destination feature for single/multi
destination scenarios that have a single encap destination.
Patches 8-10 enable multiple encap destinations for a TC flow.

From, Daniel Jurgens,
Patch 11, Use CQE padding for Ethernet CQs, PPC showed up to a 24%
improvement in small packet throughput

From Eyal Davidovich,
patches 12-14, FW monitor counter support
FW monitor counters feature came to solve the delayed reporting of
FW stats in the atomic get_stats64 ndo, since we can't access the
FW at that stage, this feature will enable immediate FW stats updates
in the driver via fw events on specific stats updates.

Patch 12, cleanup to avoid querying a FW counter when it is not
supported
Patch 13, Monitor counters FW commands support
Patch 14, Use monitor counters in ethernet netdevice to update FW
stats reported in the atomic get_stats64 ndo.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MODULE_LICENSE info to fix this:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.o
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_load':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1490:21: warning:
 variable 'upriv' set but not used [-Wunused-but-set-variable]

drivers/net/ethernet/mellanox/mlx5/core/en_rep.c: In function 'mlx5e_vport_rep_unload':
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:1557:21: warning:
 variable 'upriv' set but not used [-Wunused-but-set-variable]

It not used any more since commit ef381359 ("net/mlx5e: Replace egdev with
indirect block notifications"). Also remove unused variable 'uplink_rpriv'
after this change.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Petr Machata says:

====================
Pass extack to SWITCHDEV_PORT_OBJ_ADD

Drivers may need to do validation as a result of port object addition.
An example is mlxsw, which needs to check the configuration of a VXLAN
device attached to an offloaded bridge. Without a mapped VLAN, the
invalidity of the device is not important, but as soon as a pvid,
untagged VLAN is configured for the device, it has to be validated and
offloaded. Should the validation fail, there's currently no way to
communicate details of the failure to the user, beyond an error number.

Because currently, extack is not available at all in that area of code,
this patch starts down at the RTNL level and progresses up towards the
driver(s).

In patch #1, ndo_bridge_setlink is updated to include extack, and
callbacks of all clients are updated as well (ignoring the argument).

In patch #2, the bridge driver is updated to propagate the extack
through to the switchdev border, br_switchdev_port_vlan_add().

Patches #3, #4 and #5 then gradually extend switchdev to pass the extack
argument through to the switchdev blocking notifier chain.

Patches #6 and #7 then update mlxsw to pass the extack argument from
VXLAN events resp. port events on to mlxsw_sp_bridge_8021q_vxlan_join().

Finally in patches #8 and #9, the code paths from the previous two
patches are verified to yield an error message.

v2:
- Patch #1:
    - In ndo_bridge_setlink(), keep the whole extack declaration on the
      same line.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test mapping a VLAN at a port device such that on the same VLAN, there
already is an unoffloadable VXLAN device.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test mapping a VLAN at a VXLAN device that can't be offloaded.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After switchdev_handle_port_obj_add() was extended in a preceding patch,
mlxsw_sp_port_obj_add() now takes an extack argument. Propagate it
further by extending a callee chain from mlxsw_sp_port_vlans_add(), via
mlxsw_sp_bridge_port_vlan_add() via mlxsw_sp_port_vlan_bridge_join() via
mlxsw_sp_port_vlan_fid_join() to mlxsw_sp_bridge_ops.fid_get, adding an
extack argument for each of them.

This code path is used when a VLAN is added to a port netdevice if there
already is an unoffloadable VXLAN device with that VLAN mapped.

mlxsw_sp_bridge_8021d_port_join() is updated to obey the new interfaces
changed by the abovementioned code, propagating extack ultimately from
NETDEV_CHANGEUPPER events.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that VLAN port object addition notifications carry an extack,
propagate it from mlxsw_sp_switchdev_vxlan_vlans_add() through
mlxsw_sp_switchdev_vxlan_vlan_add() to
mlxsw_sp_bridge_8021q_vxlan_join().

This code path is used when a VLAN is added to a VXLAN netdevice that
cannot be offloaded.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers use switchdev_handle_port_obj_add() to handle recursive descent
through lower devices. Change this function prototype to take add_cb
that itself takes an extack argument. Decode extack from
switchdev_notifier_port_obj_info and pass it to add_cb.

Update mlxsw and ocelot drivers which use this helper.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NIvan Vecera <ivecera@redhat.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to pass extack to the drivers that need it, add an extack field
to struct switchdev_notifier_info, and an extack argument to the
function call_switchdev_blocking_notifiers(). Also add a helper function
switchdev_notifier_info_to_extack().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NIvan Vecera <ivecera@redhat.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NIvan Vecera <ivecera@redhat.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).

To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.

Following patches will use the new argument in the bridge driver.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_en 0000:19:00.0 (unregistered net_device) (uninitialized): hwrm
req_type 0x190 seq id 0x6 error 0xffff

The message above is commonly seen when a newer driver is used on
hardware with older firmware. The issue is this message means nothing to
anyone except Broadcom. Remove the message to not confuse users as this
message is really not very informative.
Signed-off-by: NJonathan Toppins <jtoppins@redhat.com>
Acked-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Biao Huang says:

====================
add Ethernet driver support for mt2712

Changes in v6:
 modifications according to comments from Rob/Andrew/Sean:
 1. use delay_ps instead of delay stage.
 2. add comments in driver to avoid confusion.
 2. rewrite set_delay function.
 3. modify binding document for properties: tx-delay-ps/rx-delay-ps/pericfg etc.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>