Convert cyclades to use the full tty_port_close helper
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We need to kref this driver in order to use port_close
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Start to extract and build a model for a common tty_port_close()
Signed-off-by: NAlan Cox <alan@linux.intel.com>

Prepare for the tty_port_close function by splitting out methods
Signed-off-by: NAlan Cox <alan@linux.intel.com>

Moving towards a tty_port method for open/close
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now we are extracting out methods for shutdown and the like we can add a
proper tty_port_close method that knows all the innards of the tty closing
process and hides the lot from the caller.

At some point in the future this will be paired with a similar open()
helper and the drivers can stick to hardware management.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A platform clock drives 8250 ports in most SOC systems, the clock
might run at high frequencies, and so it's not always possible to
downscale uart clock to a desired value.

Currently the 8250 uart driver accepts not supported baud rates, and
what is worse, it is doing this silently, and then passes not accepted
values to a new termios, so userspace has no chance to catch this kind
of errors (userspace verifies that settings were accepted by reading
back and comparing the settings).

This patch fixes the issue by passing minimum baud rate to the
uart_get_baud_rate() call, the call should take care of all bounds,
so userspace should now report:

  # stty -F /dev/ttyS0 speed 300
  115200
  stty: /dev/ttyS0: unable to perform all requested operations

p.s. uart_get_baud_rate() falls back to 9600, which still might be too
     low for some 10 GHz platforms, but that's a separate issue, and
     we can wait with fixing this till we find such a platform.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is currently no provision for passing IRQ trigger flags for
serial IRQs with triggering requirements (such as GPIO IRQs)

This patch adds irqflags to plat_serial8250_port that can be passed
from board file to reqest_irq() of 8250 driver

Changes are backward compatible with boards passing UPF_SHARE_IRQ flag

Tested on Zoom2 board that has IRQF_TRIGGER_RISING requirement for 8250 irq

[Moved new flag to end to fix bugs in the original with the old_serial array
	-- Alan]
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The modem ioctls are not routed via the ioctl method so kill the old dead
code. The correct code is also already present and hooked in.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I made a correction for get_lsr_info, now it returns some meaningful
information. I tested it with two simultaneous simplex modem channels.

it is attached
Signed-off-by: NKees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the tiocmget/mset handling on the mos7720 USB serial port.

[Minor space reformatting for coding style - Alan]
Signed-off-by: NKees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently kfifo cannot be used by parts of the kernel that use "const"
properly as kfifo itself does not use const for passed data blocks which
are indeed const.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The network layer now has a destructor we can hook to clean up the slip
devices array. That needs us to initiate unregister events in the right
places which with the current tty layer we can do, and with network
refcounting is safe to do.
Signed-off-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove duplicated code from cy_set_line_char. There were 2 if
branches with same contents except flags.

Branch only for the flags computation and use them in the only copy
of the code.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add helpers for io operations, so that we can eliminate huge
amount of supporting code. It is now centralized in those
helpers and used values are precomputed in the init phase.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- save one indent level by inverting !fw_loaded condition
- read rs_status on Z and write it after we change all the flags,
  don't do that separately
- remove Y inverted rts/dtr branching, precompute registers and use
  them
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- add a cy_ prefix to functions with changed prototypes
- cy_get_serial_info: initialize serial_struct by initializer,
  save a memset
- inline simple functions (get_mon_info, {s,g}et_default_threshold,
  {s,g}et_default_timeout) directly in the ioctl handler
- add a cy_cflags_changed helper to not copy its code by
  wait_event_interruptible
- remove some ret_val = 0 assignments, it's preset to 0
- TIOCGICOUNT: don't do many put_user's, do one copy_to_user
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a duplicated code for Y and Z in cy_startup, merge the paths.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For Z cards, use tty helpers for dtr_rts.

If we did the same for Y cards, it will cause a deadlock, because
cyy_dtr_rts takes a lock which we already hold.

Instead, we introduce a Y helper expecting card lock to be held.
It may then be called with set/clear masks from other places.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Avoid long busy loops (5 ms) which may be replaced by sleeps.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- remove changelog from the file. we don't care about ancient
  history
- update copyright year
- update version
- constify some stuff
- empty lines removal
- unused variables and macros removal
- remove some asm/ includes, they are sucked by linux/ variants
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use new tty helpers for close, which allows much code removal.

The only real change is locking. card_lock for protecting was
used inappropriately (just to have a critical section, no matter
which lock is used), so the change to port->lock is fine.

Remove also useless debug printks while being there.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Do not duplicate common tty_port_hangup code. Use it instead.

Also do not unset ASYNC_NORMAL_ACTIVE and wake up from the
tty_hangup() caller. It makes no sense since we don't check that
flag in sleepers. tty_port_hangup() performed later will do the
right job.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Don't fetch firmware address and recompute channel control on each
port access. Precompute the values on init and use them later all
the time.

The same for board control.

This simplify code and improves readability.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use a tty_port common instead. This saves lots of .text and makes the
code a lot more readable.

This involves separation of a dtr_rts handling, next patches will use
that to not duplicate the code all over the place.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While this is not problem for Y card handlers (they are protected
by card_lock), Z handlers and other functions may dereference NULL
at any point after hangup/close. Even if (tty == NULL) was already
performed in the handler.

Note that it's not an issue for Y cards just for now. After
switching to tty_port_close_* et al. this will be a problem. So
add refcounting to them all.

Also proc .show doesn't take a tty reference and it should (along
with a ldisc one).

While at it and changing prototypes (adding tty param), prepend
cy_ to functions which don't have it yet.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Previously, if any bit other than CMD_SND_BREAK was set, CMD_SND_BREAK
was not unset.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix the following 'make includecheck' warning:

  drivers/char/vt.c: linux/device.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now that the /proc/tty/ldiscs handling doesn't play games with 'struct
ldisc' any more, the only remaining user of 'tty_ldisc_try_get()' is
'tty_ldisc_get()' (note the lack of 'try').

And we're actually much better off folding the logic directly into that
file, since the 'try' part was always about trying to get the ldisc
operations, not the ldisc itself: and making that explicit inside of
'tty_ldisc_get()' clarifies the whole semantics.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>,
Tested-by: NSergey Senozhatsky <sergey.senozhatsky@mail.by>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The /proc/tty/ldiscs file is totally and utterly un-interested in the
"struct tty_ldisc" structures, and only cares about the underlying ldisc
operations.

So don't make it create a dummy 'struct ldisc' only to get a pointer to
the operations, and then destroy it.  Instead, we split up the function
'tty_ldisc_try_get()', and create a 'get_ldops()' helper that just looks
up the ldisc operations based on the ldisc number.

That makes the code simpler to read (smaller and more well-defined
helper functions), and allows the /proc functions to avoid creating that
useless dummy only to immediately free it again.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NSergey Senozhatsky <sergey.senozhatsky@mail.by>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ID as reported in:

http://lists.infradead.org/pipermail/linux-pcmcia/2009-May/006127.htmlReported-by: NKenneth Moorman <KMoorman@transy.edu>
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since early printk only makes sense/works when the serial driver is built
into the kernel, disable the option for this driver when it is going to be
built as a module.  Otherwise we get build failures due to the ifdef
handling.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The tty_operation chars_in_buffer() is not allowed to return a negative
value to signal an error.  Corrects the problem flagged by commit
23198fda, "tty: fix chars_in_buffers".
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Merge branch 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
  x86: Move get/set_wallclock to x86_platform_ops
  x86: platform: Fix section annotations
  x86: apic namespace cleanup
  x86: Distangle ioapic and i8259
  x86: Add Moorestown early detection
  x86: Add hardware_subarch ID for Moorestown
  x86: Add early platform detection
  x86: Move tsc_init to late_time_init
  x86: Move tsc_calibration to x86_init_ops
  x86: Replace the now identical time_32/64.c by time.c
  x86: time_32/64.c unify profile_pc
  x86: Move calibrate_cpu to tsc.c
  x86: Make timer setup and global variables the same in time_32/64.c
  x86: Remove mca bus ifdef from timer interrupt
  x86: Simplify timer_ack magic in time_32.c
  x86: Prepare unification of time_32/64.c
  x86: Remove do_timer hook
  x86: Add timer_init to x86_init_ops
  x86: Move percpu clockevents setup to x86_init_ops
  x86: Move xen_post_allocator_init into xen_pagetable_setup_done
  ...

Fix up conflicts in arch/x86/include/asm/io_apic.h

Signed-off-by: NGeoffrey Thomas <geofft@ksplice.com>
Signed-off-by: NTim Abbott <tabbott@ksplice.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is largely a straightforward conversion. The patch results in
fewer output sections, and some data being reordered, but should have
no functional impact.

Also, note that this patch moves some data (namely, init_task and
cacheline-aligned) inside [_sdata,_edata].

Because frv already builds using -ffunction-sections -fdata-sections,
we can't use BSS_SECTION or RW_DATA_SECTION yet, since they do not
currently include the required .bss.* and .data.* sections.
Signed-off-by: NNelson Elhage <nelhage@ksplice.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NTim Abbott <tabbott@ksplice.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It appears that frv copied the .altinstructions definitions in its linker
script from x86. Since frv doesn't put anything in those sections, this
is just dead code.
Signed-off-by: NNelson Elhage <nelhage@ksplice.com>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NTim Abbott <tabbott@ksplice.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (64 commits)
  ext4: Update documentation about quota mount options
  ext4: replace MAX_DEFRAG_SIZE with EXT_MAX_BLOCK
  ext4: Fix the alloc on close after a truncate hueristic
  ext4: Add a tracepoint for ext4_alloc_da_blocks()
  ext4: store EXT4_EXT_MIGRATE in i_state instead of i_flags
  ext4: limit block allocations for indirect-block files to < 2^32
  ext4: Fix different block exchange issue in EXT4_IOC_MOVE_EXT
  ext4: Add null extent check to ext_get_path
  ext4: Replace BUG_ON() with ext4_error() in move_extents.c
  ext4: Replace get_ext_path macro with an inline funciton
  ext4: Fix include/trace/events/ext4.h to work with Systemtap
  ext4: Fix initalization of s_flex_groups
  ext4: Always set dx_node's fake_dirent explicitly.
  ext4: Fix async commit mode to be safe by using a barrier
  ext4: Don't update superblock write time when filesystem is read-only
  ext4: Clarify the locking details in mballoc
  ext4: check for need init flag in ext4_mb_load_buddy
  ext4: move ext4_mb_init_group() function earlier in the mballoc.c
  ext4: Make non-journal fsync work properly
  ext4: Assure that metadata blocks are written during fsync in no journal mode
  ...

Remove net/genetlink.h inclusion, now sched.c won't be recompiled
because of some networking changes.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>