Add support for early console of MIPS Fast Debug Channel (FDC) on
channel 1 with a call very early from the MIPS setup_arch().
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9145/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add TTY driver and consoles for the MIPS EJTAG Fast Debug Channel (FDC),
which is found on the per-CPU MIPS Common Device Mapped Memory (CDMM)
bus.

The FDC is a per-CPU device which is used to communicate with an EJTAG
probe. RX and TX FIFOs exist, containing 32-bits of data and 4-bit
channel numbers. 16 general data streams are implemented on this for TTY
and console use by encoding up to 4 bytes on each 32-bit FDC word.

The TTY devices are named e.g. /dev/ttyFDC3c2 for channel 2 of the FDC
attached to logical CPU 3.

These can be used for getting the kernel log, a login prompt, or as a
GDB remote transport, all over EJTAG and without needing a serial port.

It can have an interrupt to notify of when incoming data is available in
the RX FIFO or when the TX FIFO is no longer full. The detection of this
interrupt occurs in architecture / platform code, but it may be shared
with the timer and/or performance counter interrupt.

Due to the per-CPU nature of the hardware, all outgoing TTY data is
written out from a kthread which is pinned to the appropriate CPU.

The console is not bound to a specific CPU, so output will appear on the
chosen channel on whichever CPU the code is executing on. Enable with
e.g. console=fdc1 in kernel arguments. /dev/console is bound to the same
channel on the boot CPU's FDC if it exists.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9146/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On certain cores (namely proAptiv and P5600) incoming data via a Fast
Debug Channel (FDC) while the core is blocked on a wait instruction will
cause the wait not to wake up even when another interrupt is received.
This makes an idle target stop as soon as you send FDC data to it, until
the debug probe interrupts it and restarts the wait instruction.

This is worked around by avoiding using r4k_wait on these cores if
CONFIG_MIPS_EJTAG_FDC_TTY is enabled (which would imply the user intends
to use the FDC).

[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9144/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implement the weak get_c0_fdc_int() function for Malta. The Fast Debug
Channel (FDC) interrupt is obtained mainly depending on whether a GIC is
present. Vectored external interrupt mode isn't yet supported.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9143/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a function to the MIPS GIC driver for retrieving the Fast Debug
Channel (FDC) interrupt number, similar to the existing ones for the
timer and perf counter interrupts. This will be used by platform
implementations of get_c0_fdc_int() if a GIC is present.

A workaround exists for interAptiv and proAptiv which claim to be able
to route the FDC interrupt but don't seem to be able to in practice (at
least on Malta).

[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9142/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Treat the Fast Debug Channel (FDC) interrupt the same as the timer and
performance counter interrupts. Like them, the FDC IRQ is also per-VPE,
and also doesn't use a per-CPU device ID yet. Per-CPU device IDs don't
seem to work with IRQF_SHARED which is needed for compatibility with
cores which don't route the FDC IRQ through the GIC. For hardware which
routes FDC IRQs through the GIC this is something that could be added
later.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9141/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Read the CPU IRQ line reportedly used for the Fast Debug Channel (FDC)
interrupt from the IntCtl register and store it in cp0_fdc_irq where
platform implementations of the new weak platform function
get_c0_fdc_int() can refer to it.

[ralf@linux-mips.org: Fixed conflict.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9140/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add architectural field definitions relating to the Fast Debug Channel
(FDC) interrupt, namely the pending bit in Cause and the field in
IntCtl to specify which CPU IRQ line the FDC interrupt is routed to.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9139/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Implement mips_cdmm_phys_base() for Malta, returning the physical base
address 0x1fc10000 which is "typically unused".

This allows the Common Device Memory Map (CDMM) region to be mapped, and
devices in that region (such as the Fast Debug Channel (FDC) hardware
for communication over EJTAG) to be discovered.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9177/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add MIPS Common Device Memory Map (CDMM) support in the form of a bus in
the standard Linux device model. Each device attached via CDMM is
discoverable via an 8-bit type identifier and may contain a number of
blocks of memory mapped registers in the CDMM region. IRQs are expected
to be handled separately.

Due to the per-cpu (per-VPE for MT cores) nature of the CDMM devices,
all the driver callbacks take place from workqueues which are run on the
right CPU for the device in question, so that the driver doesn't need to
be as concerned about which CPU it is running on. Callbacks also exist
for when CPUs are taken offline, so that any per-CPU resources used by
the driver can be disabled so they don't get forcefully migrated. CDMM
devices are created as children of the CPU device they are attached to.

Any existing CDMM configuration by the bootloader will be inherited,
however platforms wishing to enable CDMM should implement the weak
mips_cdmm_phys_base() function (see asm/cdmm.h) so that the bus driver
knows where it should put the CDMM region in the physical address space
if the bootloader hasn't already enabled it.

A mips_cdmm_early_probe() function is also provided to allow early boot
or particularly low level code to set up the CDMM region and probe for a
specific device type, for example early console or KGDB IO drivers for
the EJTAG Fast Debug Channel (FDC) CDMM device.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9599/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add architectural definitions and probing for the MIPS Common Device
Memory Map (CDMM) region. When supported and enabled at a particular
physical address, this region allows some number of per-CPU devices to
be discovered and controlled via MMIO.

A bit exists in Config3 to determine whether the feature is present, and
a CDMMBase CP0 register allows the region to be enabled at a particular
physical address.

[ralf@linux-mips.org: Sort conflict with other patches.]
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9178/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Before release 2 of the architecture there weren't separate interrupt
pending bits for the local CPU interrupts (timer & perf counter
overflow), so when they were connected to the same interrupt line the
timer handler had to call the performance counter handler before knowing
whether a timer interrupt was actually pending.

Now another CPU local interrupt, for the Fast Debug Channel (FDC), can
also be routed to an arbitrary interrupt line. It isn't scalable to keep
adding cross-calls between handlers for these cases of shared interrupt
lines, especially since the FDC could in theory share its interrupt line
with the performance counter, timer, or both.

Fortunately since release 2 of the architecture separate interrupt
pending bits do exist in the Cause register. This allows local
interrupts which share an interrupt line to have separate handlers using
IRQF_SHARED. Unfortunately they can't easily have their own irqchip as
there is no generic way to individually mask them.

Enable this sharing to happen by removing the special case for when the
perf count shares an IRQ with the timer. cp0_perfcount_irq and
cp0_compare_irq can then be set to the same value with shared interrupt
handlers registered for both of them.

Pre-R2 code should be unaffected. cp0_perfcount_irq will always be -1
and the timer handler will contnue to call into the perf counter
handler.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9131/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When requesting the performance counter overflow interrupt, pass flags
which are compatible with the cevt-r4k driver, in particular
IRQF_SHARED so that the two handlers can share the same IRQ. This is
possible since release 2 of the architecture where there are separate
pending interrupt bits for the timer interrupt and the performance
counter interrupt.

This will be necessary since the FDC interrupt can also be arbitrarily
routed to a CPU interrupt, possibly sharing with the timer, the
performance counters, or both, and it isn't scalable to have all the
handlers able to call other handlers that may be on the same IRQ line.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: oprofile-list@lists.sf.net
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9130/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When requesting the performance counter overflow interrupt, pass flags
which are compatible with the cevt-r4k driver, in particular
IRQF_SHARED so that the two handlers can share the same IRQ. This is
possible since release 2 of the architecture where there are separate
pending interrupt bits for the timer interrupt and the performance
counter interrupt.

This will be necessary since the FDC interrupt can also be arbitrarily
routed to a CPU interrupt, possibly sharing with the timer, the
performance counters, or both, and it isn't scalable to have all the
handlers able to call other handlers that may be on the same IRQ line.

Shared handlers must also have a unique device pointer so they can be
individually removed, so &mipspmu is now passed in for that instead of
NULL.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9129/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The attempt to get gcc to generate best possible code turned
c0_compare_interrupt() into a bit of Italian pasta code.  Tweak for
sanity.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make the cevt-r4k interrupt handler shared so that other interrupt
handlers (specifically the performance counter overflow handler and fast
debug channel interrupt handler) can share the same interrupt line.

This simply imvolves returning IRQ_NONE when no timer interrupt has been
handled to allow other handlers to run, and passing IRQF_SHARED when
setting up the IRQ handler so that other handlers (with compatible
flags) can be registered.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9128/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add missing VPE_PEND, VPE_RMASK and VPE_SMASK definitions for the local
FDC interrupt.

These local interrupt definitions aren't directly used, but if they
exist they should be complete.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9127/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix typo in comment in gic_get_c0_perfcount_int:
"erformance" -> "performance".
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAndrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9126/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The situation where the timer interrupt is on the same line as the
performance counter interrupt is handled in per_cpu_trap_init() by
setting cp0_perfcount_irq to -1, so there is no need to duplicate the
logic conditional upon cp0_perfcount_irq >= 0 in perf
(init_hw_perf_events()) and oprofile (mipsxx_init()).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9125/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use CAUSEF_TI and CAUSEF_PCI constants from asm/mipsregs.h rather than
the magic values (1 << 30) and (1 << 26).
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9124/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Long ago, commit 8531a35e ("[MIPS] SMTC: Fix SMTC dyntick support.")
moved handle_perf_irq() out of cevt-r4k.c into a header so it could be
shared with cevt-smtc.c.

Slightly less long ago, commit b633648c ("MIPS: MT: Remove SMTC
support") removed all traces of SMTC support, including cevt-smtc.c,
leaving cevt-r4k.c once again the sole user of handle_perf_irq(),
therefore move it back into cevt-r4k.c from the header.
Signed-off-by: NJames Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9123/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a defconfig for Pistachio which enables drivers for all the
currently supported peripherals on the SoC.
Signed-off-by: NGovindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9570/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add initial support for boards based on the Imagination Pistachio SoC.
Pistachio is based on a dual-core MIPS interAptiv CPU and will boot
using device-tree.
Signed-off-by: NJames Hartley <james.hartley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9569/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Pistachio SoC boots only with device-tree.  Document the required
properties and nodes as well as the boot protocol between the bootlaoder
and the kernel.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9568/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Platforms which use raw zboot images may need to link the image at
a fixed address if there is no other way to communicate the load
address to the bootloader.  Allow the per-platform Kbuild files
to specify an optional zboot image load address (zload-y) and fall
back to calc_vmlinuz_load_addr if unset.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9566/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

11 platforms require at least one of these workarounds to be enabled; 22
platforms do not.  In the latter case we can fall back to a generic version.

Note that this also deletes an orphaned reference to RM9000_CDEX_SMP_WAR.
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Reviewed-by: NJames Hogan <james.hogan@imgtec.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9567/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the clock gates for the external audio and ethernet
reference clocks provided by the top-level general control block.
Signed-off-by: NDamien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9321/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the system interface gate clocks provided by the peripheral
general control block.  These clocks gate register access for various
peripherals.
Signed-off-by: NDamien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9322/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the clocks generated by the peripheral clock controller.
This includes the clocks for several peripherals, including I2C,
PWM, watchdog, and timer.
Signed-off-by: NDamien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9320/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Register the clocks generated by the core clock controller.
This includes the 7 PLLs and clocks for the CPU, RPU co-processor,
audio, WiFi, bluetooth, and several other peripherals.

The MIPS and PERIPH_SYS clocks must remain enabled at all times.
Signed-off-by: NDamien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9317/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a driver for the integer (GF40LP_LAINT) and fractional (GF40LP_FRAC)
PLLs present on Pistachio.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9316/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add helpers for registering clocks and clock providers on Pistachio.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9318/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a device-tree binding document describing the four clock
controllers present on the IMG Pistachio SoC.
Signed-off-by: NDamien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Patchwork: https://patchwork.linux-mips.org/patch/9319/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Enable user to select OCTEON SHA1/256/512 modules.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9492/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add OCTEON SHA512 module.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9496/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add OCTEON SHA256 module.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9493/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add OCTEON SHA1 module.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9495/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add instruction definitions for SHA1/256/512.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9491/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Always disable preemption on behalf of the drivers when crypto engine
is taken into use. This will simplify the usage.
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9494/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Don't disable bottom half while the crypto engine is in use, as it
should be unnecessary: All kernel crypto engine usage is wrapped with
crypto engine state save/restore, so if we get interrupted by softirq
that uses crypto they should save and restore our context.

This actually fixes an issue when running OCTEON MD5 with interrupts
disabled (tcrypt mode=302). There's a WARNING because the module is
trying to enable the bottom half with irqs disabled:

[   52.656610] ------------[ cut here ]------------
[   52.661439] WARNING: CPU: 1 PID: 428 at /home/aaro/git/linux/kernel/softirq.c:150 __local_bh_enable_ip+0x9c/0xd8()
[   52.671780] Modules linked in: tcrypt(+)
[...]
[   52.763539] [<ffffffff8114082c>] warn_slowpath_common+0x94/0xd8
[   52.769465] [<ffffffff81144614>] __local_bh_enable_ip+0x9c/0xd8
[   52.775390] [<ffffffff81119574>] octeon_md5_final+0x12c/0x1e8
[   52.781144] [<ffffffff81337050>] shash_compat_digest+0xd0/0x1b0
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9490/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>