In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new config for 4165 series over PCI and insert support
for two new 4165 series PCI IDs.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Organize and cleanup the consts used by rs.
This is part of making some of these configurable.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make passive scan fragmentation depends on the number of active
interfaces. In case of single-MAC, make passive scan less fragmented.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to config the FW and to allocate monitor buffer driver should
run the function iwl_pcie_apply_destination immediately after FW sections
are loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration defines the ratio between number of scan iterations
where EBS is involved to those where it is not.
This configuration was left unconfigured due to inaccurate documentation.
Fix documentation as well.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the wakeup flag (of the d3 command) to configure the fw
to wakeup when sysassert happens while in d0i3.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new TLV supplies the ADMA address for SDIO mode, allowing
the driver to configure the default base address to be this
(as given in the FW), rather than hardcoding the values to
use until the FW sends the ALIVE message.

Use the value given by the FW in the IWL_UCODE_TLV_SDIO_ADMA_ADDR
TLV for setting the default SDTM base address until the FW sends
the ALIVE message. If it isn't given in the FW - use the current
hardcoded values.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A number of places (still) use a direct operation, use
iwl_mvm_sta_from_mac80211() consistently. In one place
also move it into the variable initializer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a few places not using it, use it at those places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This device was renamed, but the external definition remained there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some implementations (i.e. mini_rpm) assume the references
are managed only while the device is started.

Move the stale reference cleanup before stopping the
device in order to make them happy.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver and the firmware now support 2 different channels
at the same time. Advertise this capability to the stack.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On hw restart, make sure to wait for d0i3 exit
(by checking the IN_D0I3 status bit).

This is needed in order to avoid the stale
d0i3_exit_work from doing harm (e.g. unref
cleared reference).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Consider the iwlwifi module param d0i3_disable when
considering whether d0i3 is supported.

(There is currently no need to differentiate between
supported and enabled, so keep the function as-is)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.

Use this mode in case of pcie trans.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow configuring additional d0i3 mode, in which the
fw will be configured to enter d0i3 only on suspend
(while keeping the wake_lock accounting as usual)

The d0i3 mode to use will be determined by the
underlying trans layer.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

d3 and d0i3 shouldn't be mutually exclusive. Set supported
wowlan triggers by looking for each of them, and check
on suspend/resume which flow should be used ("any" trigger
is supported by d0i3, and all the others by d3)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement the ref/unref trans ops and track both tx and
host command queues (and hold references while they
are not empty).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to add the offset. The type of the generic
memory dump will let the parser know that this is SRAM.
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of adding a dump type for each type of memory, change
the SMEM type to be a general purpose memory dump. Add the
type of the memory and its offset in the device in the dump
itself. This will allow an external parser to know where
this memory came from.

Note that since this type isn't really in use yet, this is
not a real problem.
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In NICs that have SMEM - add its content to the dump data
for later debug.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

nvm_file in family 8000 B step and A step differ. This means
that the driver should support 2 file name as default.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case the rate mask for one of the modulations was zero the
max rate idx for that modulation was set to 32 (BITS_PER_LONG).
This is bad as it would later lead to an out of bounds access
to the expected tpt table. In most cases there was no real effect
as the expected tpt was set to 0 and this led to avoiding the
modulation effectively.
Fix the out of bounds access and explicitly skip the modulation
in case there's no rate allowed in it.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Clear the thermal throttling values when entering CT-kill, since
everything will be reinitialized anyway when we exit CT-kill.

Additionally, clear the dynamic_smps value in the initialization
funciton, for consistency.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The HW step member was left out of the core dump information. Fix this.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware is able to compensate the rssi when we hear
the frame on a different channel.
This is true for an offset up to 3 channels.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to collect the logs even if the firmware hasn't
crashed. Of course, crashing the firmware is an option, but
this is easier and nicer.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the driver is unload, the Manageability Engine should
know about that - send an event to inform it about this
event.
Reviewed-by: NReuven Borok <reuven.borok@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The antenna configuration has to be read also from OTP
Currently read only from FW image
Guideline: An antenna exists only if appears both in FW image & NVM
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The allocation of the DCCM between the data and the stack
can theoretically change without notice to the driver, but
the total size is HW-fixed. Since the stack CCM (runtime
stack) has also data important to the FW - this patch allows
pulling the whole DCCM in one piece and adds it to the dump
data.

If the size isn't known - just use the data part of the
DCCM as it appears in the FW TLVs.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The module version "in-tree:" or "in-tree:d" is useless; there
should be better (functional) ways to detect whether debugging
is enabled and other than that the version says nothing.

Therefore remove the driver version completely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) New offloading infrastructure and example 'rocker' driver for
    offloading of switching and routing to hardware.

    This work was done by a large group of dedicated individuals, not
    limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
    Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu

 2) Start making the networking operate on IOV iterators instead of
    modifying iov objects in-situ during transfers.  Thanks to Al Viro
    and Herbert Xu.

 3) A set of new netlink interfaces for the TIPC stack, from Richard
    Alpe.

 4) Remove unnecessary looping during ipv6 routing lookups, from Martin
    KaFai Lau.

 5) Add PAUSE frame generation support to gianfar driver, from Matei
    Pavaluca.

 6) Allow for larger reordering levels in TCP, which are easily
    achievable in the real world right now, from Eric Dumazet.

 7) Add a variable of napi_schedule that doesn't need to disable cpu
    interrupts, from Eric Dumazet.

 8) Use a doubly linked list to optimize neigh_parms_release(), from
    Nicolas Dichtel.

 9) Various enhancements to the kernel BPF verifier, and allow eBPF
    programs to actually be attached to sockets.  From Alexei
    Starovoitov.

10) Support TSO/LSO in sunvnet driver, from David L Stevens.

11) Allow controlling ECN usage via routing metrics, from Florian
    Westphal.

12) Remote checksum offload, from Tom Herbert.

13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
    driver, from Thomas Lendacky.

14) Add MPLS support to openvswitch, from Simon Horman.

15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
    Klassert.

16) Do gro flushes on a per-device basis using a timer, from Eric
    Dumazet.  This tries to resolve the conflicting goals between the
    desired handling of bulk vs.  RPC-like traffic.

17) Allow userspace to ask for the CPU upon what a packet was
    received/steered, via SO_INCOMING_CPU.  From Eric Dumazet.

18) Limit GSO packets to half the current congestion window, from Eric
    Dumazet.

19) Add a generic helper so that all drivers set their RSS keys in a
    consistent way, from Eric Dumazet.

20) Add xmit_more support to enic driver, from Govindarajulu
    Varadarajan.

21) Add VLAN packet scheduler action, from Jiri Pirko.

22) Support configurable RSS hash functions via ethtool, from Eyal
    Perry.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
  Fix race condition between vxlan_sock_add and vxlan_sock_release
  net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
  net/mlx4: Add support for A0 steering
  net/mlx4: Refactor QUERY_PORT
  net/mlx4_core: Add explicit error message when rule doesn't meet configuration
  net/mlx4: Add A0 hybrid steering
  net/mlx4: Add mlx4_bitmap zone allocator
  net/mlx4: Add a check if there are too many reserved QPs
  net/mlx4: Change QP allocation scheme
  net/mlx4_core: Use tasklet for user-space CQ completion events
  net/mlx4_core: Mask out host side virtualization features for guests
  net/mlx4_en: Set csum level for encapsulated packets
  be2net: Export tunnel offloads only when a VxLAN tunnel is created
  gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
  cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
  net: fec: only enable mdio interrupt before phy device link up
  net: fec: clear all interrupt events to support i.MX6SX
  net: fec: reset fep link status in suspend function
  net: sock: fix access via invalid file descriptor
  net: introduce helper macro for_each_cmsghdr
  ...