Update comments to conform to the preferred style for networking code as
described in ./Documentation/CodingStyle and checked for in the recently
added checkpatch NETWORKING_BLOCK_COMMENT_STYLE test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables flow control to be set in SerDes autoneg mode.  This is
done the way it is done for copper, but relies on a different set of register/bit
checks since this is all done within the MAC registers.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch unsets the sigdetect bit for SERDES loopback tests on 82580 and
i350 parts.  The loopback test can fail on these parts without this
setting.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to a hw errata, the global device reset doesn't always work on 82580
devices.  This patch works around the problem not trying to do a global
device reset on these devices.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors the functions in e1000_i210.c in order to remove need
for prototypes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows software acquires and releases NVM resource for
writing each EEPROM page, instead of holding semaphore for the whole
data block which is too long and could trigger write fails on
unpredictable addresses.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i211 has an integrated secure space to store configuration information that is
usually stored in an EEPROM or flash type device. This patch updates the
read functions to return values or appropriate error codes to prevent
unnecessary init failures on some configuration schemes.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces calls to copy_to_user, copy_from_user, and the associated
logic, with calls to simple_read_from_buffer and simple_write_to_buffer
respectively.  This was done to eliminate warnings generated by the Smatch
static analysis tool.

v2- Fix return values based community feedback
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJosh Hay <joshua.a.hay@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Unlike LRO, GRO requires that vlan tags be removed before
aggregation can occur.  Since the myri10ge NIC does not support
hardware vlan tag offload, we must remove the tag in the driver
to achieve performance comparable to LRO for vlan tagged frames.

Thanks to Eric Duzamet for his help simplifying the original patch.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert myri10ge from LRO to GRO, and simplify the driver by removing
various LRO-related code which is no longer needed including
ndo_fix_features op, custom skb building from frags, and LRO
header parsing.
Signed-off-by: NAndrew Gallatin <gallatin@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CC      drivers/net/ethernet/ti/cpsw.o
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_ndo_ioctl':
drivers/net/ethernet/ti/cpsw.c:881:20: warning: unused variable 'priv'

The build warning is generated when CPTS is not selected in Kernel Build.
Fixing by passing the net_device pointer to cpts IOCTL instead of passing priv
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ff33c0e1 ('net: Remove bogus
dependencies on INET') wrongly removed this dependency.  cxgb3 uses
the arp_send() function defined in net/ipv4/arp.c.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On BE2 chip, an interrupt may be raised even when EQ is in un-armed state.
As a result be_intx()::events_get() and be_poll:events_get() can race and
notify an EQ wrongly.

Fix this by counting events only in be_poll(). Commit 0b545a62 fixes
the same issue in the MSI-x path.

But, on Lancer, INTx can be de-asserted only by notifying num evts. This
is not an issue as the above BE2 behavior doesn't exist/has never been
seen on Lancer.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove an outdated comment, that should have been removed in the
patch named "MODULE_PARM conversions" from early 2005.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building ewrk3.o triggers this GCC warning:
    drivers/net/ethernet/dec/ewrk3.c: In function '__check_irq':
    drivers/net/ethernet/dec/ewrk3.c:1915:1: warning: return from incompatible pointer type [enabled by default]

This can be trivially fixed by changing the 'irq' parameter from int to
byte (which is an alias for unsigned char for module parameters).
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Had a typo in memcpy.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style violations in qlcnic_minidump.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter register dump utility.

Move register dump routines to new file qlcnic_minidump.c
Existing register dump routines has coding style issues, the code
is moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_minidump.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style issues in qlcnic_sysfs.c file
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter sysfs routines.

Move sysfs routines to new file qlcnic_sysfs.c
Existing sysfs routines has coding style issues, this code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_sysfs.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix coding style issues in qlcnic_io.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Physical refactoring of 82xx adapter data path routines.

Move data path code to new file qlcnic_io.c
Existing data path code has coding stye issues, the code is
moved to the new file without fixing the style issues.

There is a seperate patch to fix the style issues in qlcnic_io.c
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is not a real problem, since the EEE is supported for devices where the
actual_phy_selection is zero, such that the req_duplex of params will match
the one of the phy struct.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The string was split to several lines since it reached over 180 chars, which
seems too much.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes some cosmetic changes to the code:
1. Code alignment.
2. Merge read-modify-write into a single function (read_or_write /
read_and_write).
3. Merge several write registers into a for-loop write using a static array.
4. Remove empty lines.
5. Fix comments.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.

Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per measurements, the SFP+ suffered from small current leakage in two cases:
 - When no module was plugged and TX laser was disabled. The fix was to enable
   it, and when module is plugged in, check if it needs to be disabled.
 - When over-current event occurs due to invalid SFP+ module, the HW basically
   shuts down the current for this module, but the SW needs to complete this
   by issuing a power down via a GPIO.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the version string to better reflect the driver functionality with
that of the out of tree driver.  Also since we no longer need the MAJ,
MIN, BUILD defines remove them to clean up the code.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The internal bridge mode setting needs to be sticky so that it can be
configured correctly after a device reset.  This change is required now
that the driver supports setting the bridge mode to VEB or VEPA.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The XOFF received statistic registers are per priority based and not per
traffic class. The ixgbe driver was incorrectly considering them to be for
each traffic class; and then disabling the "Tx hang" check for the queues
that belonged to the particular traffic class that had received PFC frames.

The above logic worked fine in scenario where the user priority and traffic
class number matched e.g. priority 0 is mapped to traffic class 0 and so on.
But, when multiple user priorities are mapped to a single traffic class or
when user priorities and traffic class numbers do not line up; the ixgbe
driver may disable the "Tx hang" check for queues belonging to a traffic
class that did not receive PFC frames and keep the "Tx hang" check enabled
for the queues that did receive the PFC frames.

This patch corrects the above in the code by considering the statistics
on a per priority basis; then getting the traffic class the user priority
belongs to and disabling the "Tx hang" check for queues that belong
to that traffic class.
Signed-off-by: NNeerav Parikh <Neerav.Parikh@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we are doing a page based receive there is no point in setting a maximum
packet length on the x540 RXDCTL register.  As such we can drop the code from
the driver entirely.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For some devices, the result of the flow control high watermark gets
truncated when programming it into the registers because of the mask used.
Switch the mask to 32-bit to prevent this from happening.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update version number.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On i350 VF devices, VLAN tags will be byte-swapped in the receive
descriptor only when received packets are looped back from other
VFs. Check for this condition and swab the tag if needed.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Common Platform Time Sync function of the CPSW does not depend the
CPSW configuration option as it should. This patch fixes the issue by
adding the dependency.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many new feauture have been introduced in the driver:
ethtool coalesce options, Rx HW watchdog... so this patch updates the
driver's version.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>