Commit 4e27f752 ("ARM: OMAP2+: Drop mmc platform data for am330x and
am43xx") dropped legacy mmc platform data for am3 and am4, but missed the
fact that we never updated the dts files for mmc3 that is directly on l3
interconnect instead of l4 interconnect. This leads to a situation with
no legacy platform data and incomplete dts data.

Let's update the mmc instances on l3 interconnect to probe properly with
ti-sysc interconnect target module driver to make mmc3 work again. Let's
still keep legacy "ti,hwmods" property around for v5.2 kernel and only
drop it later on.

Note that there is no need to use property status = "disabled" for mmc3.
The default for dts is enabled, and runtime PM will idle unused instances
just fine.

Fixes: 4e27f752 ("ARM: OMAP2+: Drop mmc platform data for am330x and am43xx")
Reported-by: NDavid Lechner <david@lechnology.com>
Tested-by: NDavid Lechner <david@lechnology.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.

In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.

In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.

Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Convert AM43xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.

arch/arm/boot/dts/am437x-idk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am437x-sk-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am43x-epos-evm.dtb: Warning (spi_bus_bridge): /ocp@44000000/qspi@47900000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/omap3-n9.dtb: Warning (i2c_bus_reg): /ocp@68000000/i2c@48060000/ak8975@0f: I2C bus unit address format error, expected "f"
arch/arm/boot/dts/am335x-osd3358-sm-red.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/pressure@78: I2C bus unit address format error, expected "76"
arch/arm/boot/dts/am335x-boneblack.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-boneblack-wireless.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am335x-sancloud-bbe.dtb: Warning (i2c_bus_reg): /ocp/i2c@44e0b000/tda19988: I2C bus unit address format error, expected "70"
arch/arm/boot/dts/am571x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am572x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am574x-idk.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-cl-som-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am57xx-sbc-am57x.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra72-evm-revc.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra76-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/dra7-evm.dtb: Warning (spi_bus_bridge): /ocp/qspi@4b300000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/am335x-pdu001.dtb: Warning (spi_bus_reg): /ocp/spi@481a0000/cfaf240320a032t: SPI bus unit address format error, expected "0"
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (spi_bus_bridge): /soc@0/qspi@2940000: node name for SPI buses should be 'spi'

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: NRob Herring <robh@kernel.org>
[tony@atomide.com: fixed mode to 644 for am335x-osd3358-sm-red.dts while at it]
Signed-off-by: NTony Lindgren <tony@atomide.com>

RTC alarm2 is connected to pmic_en line and hence can be used to control
the pmic enabling/disabling. Hence add the system-power-controller for rtc
node.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The EMIF instance on am43xx supports interrupts, so add the info for
completeness sake. Right now, the driver does not use this for anything,
but it is possible it would be used in future.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We can never idle the l3_main hwmod so mark the omap_l3_noc node
with ti,no-idle.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.

Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have
leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have
leading 0s

Converted using the following command:

$ find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec \
sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" \
-e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C

For simplicity, two sed expressions were used to solve each warnings
separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This will solve as a side effect warning:

Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format
error, expected "<lower>"

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading
0x from bindings notation")
Reported-by: NDavid Daney <ddaney@caviumnetworks.com>
Suggested-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMathieu Malaterre <malat@debian.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add clkctrl nodes for AM43xx SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.

This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add simple-bus compatibility and ranges properties to prcm node. This is
done in preparation of adding the support for clkctrl nodes.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the functional clock definition for timers1/2. This is needed so that
the clock rate calculations continue to function properly once am33xx
transitions away from hwmod data and towards the clkctrl clocks.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixes the following warnings:

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000

arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The operatings-points-v2 table for am4372 was merged before any user of
it was present in the kernel and before the binding had been finalized.
The new ti-cpufreq driver and binding expects the platform specific
properties to be part of the operating-points-v2 table rather than the
cpu node so let's move them there as the only user is the ti-cpufreq
driver.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
eviewed-by: NLukasz Majewski <lukma@denx.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Even if no_bd_ram property is described in TI CPSW bindings the support for
it has never been introduced in CPSW driver, so there are no real users of
it. Hence, remove no_bd_ram property from documentation and DT files.

Cc: 'Rob Herring <robh+dt@kernel.org>'
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 75813028 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
removed the skeleton.dtsi usage since we want to get rid of it.

But this can cause issues when booting a kernel with a boot-loader
that doesn't create a chosen node if this isn't present in the DTB
since the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info.

Fixes: 75813028 ("ARM: dts: am4372: Remove skeleton.dtsi usage")
Reported-by: NPali Rohar <pali.rohar@gmail.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add DMA properties for tscadc
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.

Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings:

"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2 arm64: dts: kill skeleton.dtsi").

These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:

"Node /memory has a reg or ranges property, but no unit name"

The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it shouldn't have
functional changes.

Since no am4372 based board had a memory node defined, a dummy node
is added so the compiled DTB memory node is the same than before.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the following DTC warnings for many boards:

"Node /ocp has a reg or ranges property, but no unit name"
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add "ti,cpsw-mdio" for am335x/am437x/dra7 SoCs where MDIO is
implemented as part of TI CPSW and, this way, enable PM runtime auto
suspend for Davinci MDIO driver on these paltforms.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding DT node for hardware random number generator.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There is no reason to hold s/w dependent parameter in device tree.
Even more, there is no reason in this parameter because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels
anyway.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct misspelling, "emda3" -> "edma3".
Reported-by: NAdam J Allison <adamj.allison@gmail.com>
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add an operating-points-v2 table with all OPPs available for all silicon
revisions along with necessary data for use by ti-cpufreq to selectively
enable the appropriate OPPs at runtime.

Information from AM437x Data Manual, SPRS851B, Revised April 2015,
Table 5-2.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Previous patches switched the ECAP and EPWM to use the new bindings.
These bindings explicitly adds the various required clocks via DT rather
than depending on hwmod.

Therefore, it is safe to remove the hwmod entries since they are no longer
needed.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
provide the various required clocks.

For AM437 and AM335x, add the required clocks explicitly to DT. The
hwmod entries for ECAP and EPWM will be removed and this will prevent
anything from breaking.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.

Fixes: cce1ee00 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPMC driver provides GPI support for the GPMC_WAIT pins.
Mark it gpio controller capable.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

When possible generic node names should be used. So change the node name
from ehrpwm to pwm.
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

EDMA was allocating DMA channels 32 and 33 for memcpy usage, out of which
channel 33 is actually used by DES crypto engine. This bad allocation of
the channel causes a crash in the DES crypto engine, as the channel
gets configured for memcpy usage instead of hardware <-> memory DMA.

Fixed by allocating DMA channels 58 and 59 for memcpy usage (I2C0 RX/TX),
which are not used by anybody.

Fixes: cce1ee00 ("ARM: DTS: am437x: Use the new DT bindings for
the eDMA3")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Suggested-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.

The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add "syscon-phy-power" property and remove the deprecated "ctrl-module"
property from SATA and USB PHY node. Also remove the unused control
module dt nodes.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.

and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.

Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add ti,mbox-send-noirq to wkup_m3 mailbox so that messages using
wkup_m3 mailbox are sent without triggering any further interrupts.
This is required to be able to send multiple messages to the WkupM3
after the mailbox usage logic adjustment in the wkup_m3_ipc driver.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NDave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise commit description]
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>