Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the skb->protocol field is used to setup various
offloading parameters on transmit for the correct protocol.
However, if vlan offloading is disabled or otherwise not used,
the protocol field will be ETH_P_8021Q, not the actual protocol.
This will cause the offloading to be not performed correctly,
even though the hardware is capable of looking inside vlan tags.
Instead, look inside the header if necessary to determine the
correct protocol type.

To some extent this fixes a regression from 2.6.36 because it
was previously not possible to disable vlan offloading and this
error case was not exposed.
Signed-off-by: NHao Zheng <hzheng@nicira.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DCB credits refill quantum _must_ be greater than half the max
packet size. This is needed to guarantee that TX DMA operations
are not attempted during a pause state. Additionally, the min IFG
must be set correctly for DCB mode. If a DMA operation is
requested unexpectedly during the pause state the HW data
store may be corrupted leading to a DMA hang.  The DMA hang
requires a reset to correct. This fixes the HW configuration
to avoid this condition.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FCoE offload is enabled/disabled per adapter, but upper FCoE protocol
stack could have multiple FCoE instances created on the same physical network
interface, e.g., FCoE on multiple VLAN interfaces on the same physical
network interface. In this case we want to turn on FCoE offload at the first
request from ndo_fcoe_enable() but only turn off FCoE offload at the very last
call to ndo_fcoe_disable(). This is fixed by adding a refcnt in the per adapter
FCoE structure and tear down FCoE offload when refcnt decrements to zero.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current ixgbe stats have following problems :

- Not 64 bit safe (on 32bit arches)

- Not safe in ixgbe_clean_rx_irq() :
   All cpus dirty a common location (netdev->stats.rx_bytes &
netdev->stats.rx_packets) without proper synchronization.
   This slow down a bit multiqueue operations, and possibly miss some
updates.

Fixes :

Implement ndo_get_stats64() method to provide accurate 64bit rx|tx
bytes/packets counters, using 64bit safe infrastructure.

ixgbe_get_ethtool_stats() also use this infrastructure to provide 64bit
safe counters.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update copyright notice
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the ixgbe driver use the new vlan accleration model.
Signed-off-by: NJesse Gross <jesse@nicira.com>
CC: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb.  There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances.  However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a DCB check config from DCB configuration we
continue to configure DCB even if it fails so don't
even bother to check.  Plus user space (lldpad) checks
this before programming the hw anyways.

Worse case is we program some values into the hw that
don't make total sense resulting in incorrect bandwidth
allocation.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Following patch fixes warnings reported by `make namespacecheck`

Reported by Stephen Hemminger

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove functions that are declared, but not used in the driver.
This patch fixes warnings reported by `make namespacecheck`

Reported by Stephen Hemminger

CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new infrastructure to balance interrupts for flow
alignment when ATR or Flow Director are enabled.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix possible panic/hang with shared Legacy interrupts by not enabling
interrupts when interface is down.

Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr()

This patch adds flags to ixgbe_irq_enable() to allow for some flexibility
when enabling interrupts.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Tested-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set.  Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce indentation in a couple of places
Add static function ixgbe_psum
Add temporary for adapter->stats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Did not add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
because no printk in this module used message prefixing.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whitespace cleanups.
Move inline keyword after function type declarations.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ordering of operations was messed up in the init and as a result when
VMDQ was enabled we were trying to enable TX rings before setting the VFTE
bits. This resulted in a ring that appeared to fail to enable when in fact
it was blocked because the VFTE bits were cleared after the reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fresh skbs have ip_summed set to CHECKSUM_NONE (0)

We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.

Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.

Change most occurrences of :

skb->ip_summed = CHECKSUM_NONE;

by :

skb_checksum_none_assert(skb);
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"foo = &function" is more commonly written "foo = function"

Done with coccinelle script:

// <smpl>
@r@
identifier f;
@@

f(...) { ... }

@@
identifier r.f;
@@

- &f
+ f
// </smpl>

drivers/net/tehuti.c used a function and struct with the
same name, the function was renamed.

Compile tested x86 only.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that the ethtool loopback test uses the standard
ring configuration and allocation functions.  As a result the loopback test
will be much more effective at testing core driver functionality.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All of the DESC_ADV macros are currently needing the pointers to be
de-referenced before accessing the ring.  Instead of having to add all of
the asterisks it is easier to just update the macro to expect a pointer to
the ring.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Rx init is currently split over ixgbe_configure, ixgbe_configure_rx,
and ixgbe_up_complete.  Instead of leaving it split over 3 function it is
easier to consolidate them all into ixgbe_configure_rx.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Tx init was spread out over ixgbe_configure, ixgbe_configure_tx, and
ixgbe_up_complete.  This change combines all of that into the
ixgbe_configure_tx function in order to simplify the Tx init path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves all GPIE register configuration into a single function.
The advantage of this is that we can avoid a number of unnecessary
read/modify/write cycles on the register.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves the configuration that was done in configure_rx into a
separate virtualization configuration function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves all of the Rx DMA control register writes to one central
location.  This should help to avoid accidentally overwriting existing
settings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change consolidates all of the Rx max frame size and Rx buffer length
configuration into a single function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vmolr is configured already in ixgbe_set_rx_mode for the PF so there is
no need to set it again in ixgbe_configure_rx.

Instead of using the variable name reg, it is easier to just rename it to
gcr_ext to reflect the register contents that the variable holds.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump the header size for packet split to 512 bytes since this makes the
best use of the 1k buffer that is allocated for any skb 512 bytes or
smaller.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are accessing the FCTRL register in multiple spots in the init path and
we can simplify things by combining the configuration all into
ixgbe_set_rx_mode.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configuration of PSRTYPE was being done conditionally on if packet
split is enabled or not.  It can be configured always since it will not
have any effect when packet split is not enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These changes add ixgbe_configure_rx_ring which is used to setup the base
function pointers for the ring.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change simplifies the configuration of MRQC by consolidating the
setting of it into one function. As such the register is no longer set in
multiple places which should make any future changes easier to work with.
In addition we can combine RSS related register writes into the call since
enabling all of those bits without enabling RSS itself in MRQC should have
no effect.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the Tx ring configuration into a separate function.  In
addition the function drops the setting of the head writeback RO bit since
head writeback is no longer used within ixgbe.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the configuration of the MTQC register into it's own
function call similar to ixgbe_setup_mrqc.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>