Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.

Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NRadhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.

Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions

This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.

This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.

Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NRadhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[  614.050361] net eth0: DMA Tx error 0x174019
[  614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[  614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[  614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[  614.135428] 3 locks held by kworker/u4:4/40:
[  614.149075]  #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[  614.177528]  #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[  614.209033]  #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[  614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[  614.260854] Hardware name: ARM Test FPGA (DT)
[  614.274734] Workqueue: rpciod rpc_async_schedule
[  614.289022] Call trace:
[  614.296871]  dump_backtrace+0x0/0x1a0
[  614.308311]  show_stack+0x14/0x20
[  614.318751]  dump_stack+0xbc/0x100
[  614.329403]  ___might_sleep+0xf0/0x140
[  614.341018]  __might_sleep+0x4c/0x80
[  614.352201]  __mutex_lock+0x5c/0x8a8
[  614.363348]  mutex_lock_nested+0x1c/0x28
[  614.375654]  axienet_dma_err_handler+0x38/0x388
[  614.389999]  tasklet_action_common.isra.15+0x160/0x1a8
[  614.405894]  tasklet_action+0x24/0x30
[  614.417297]  efi_header_end+0xe0/0x494
[  614.429020]  irq_exit+0xd0/0xd8
[  614.439047]  __handle_domain_irq+0x60/0xb0
[  614.451877]  gic_handle_irq+0xdc/0x2d0
[  614.463486]  el1_irq+0xcc/0x180
[  614.473451]  __tcp_transmit_skb+0x41c/0xb58
[  614.486513]  tcp_write_xmit+0x224/0x10a0
[  614.498792]  __tcp_push_pending_frames+0x38/0xc8
[  614.513126]  tcp_rcv_established+0x41c/0x820
[  614.526301]  tcp_v4_do_rcv+0x8c/0x218
[  614.537784]  __release_sock+0x5c/0x108
[  614.549466]  release_sock+0x34/0xa0
[  614.560318]  tcp_sendmsg+0x40/0x58
[  614.571053]  inet_sendmsg+0x40/0x68
[  614.582061]  sock_sendmsg+0x18/0x30
[  614.593074]  xs_sendpages+0x218/0x328
[  614.604506]  xs_tcp_send_request+0xa0/0x1b8
[  614.617461]  xprt_transmit+0xc8/0x4f0
[  614.628943]  call_transmit+0x8c/0xa0
[  614.640028]  __rpc_execute+0xbc/0x6f8
[  614.651380]  rpc_async_schedule+0x28/0x48
[  614.663846]  process_one_work+0x298/0x6a8
[  614.676299]  worker_thread+0x40/0x490
[  614.687687]  kthread+0x134/0x138
[  614.697804]  ret_from_fork+0x10/0x18
[  614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[  615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to axienet, the temac driver is now architecture agnostic, and
can be at least compiled for several architectures.
Especially the fact that this is a soft IP for implementing in FPGAs
makes the current restriction rather pointless, as it could literally
appear on any architecture, as long as an FPGA is connected to the bus.

The driver hasn't been actually tried on any hardware, it is just a
drive-by patch when doing the same for axienet (a similar patch for
axienet is already merged).

This (temac and axienet) have been compile-tested for:
alpha hppa64 microblaze mips64 powerpc powerpc64 riscv64 s390 sparc64
(using kernel.org cross compilers).
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NRadhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.

The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).

Fixes: f70bb065 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: NVladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use readl_poll_timeout() to replace the poll codes for simplify
iproc_mdio_wait_for_idle() function
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.7

Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.

When merging with wireless-drivers this pull request has a conflict in:

drivers/net/wireless/intel/iwlwifi/pcie/drv.c

To solve that just drop the changes from commit cf52c8a7 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.

Major changes:

qtnfmac

* support WPA3 SAE and OWE in AP mode

ath10k

* support for getting btcoex settings from Device Tree

* support QCA9377 SDIO device

ath11k

* add HE rate accounting

* add thermal sensor and cooling devices

mt76

* MT7663 support for the MT7615 driver
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
PTP_CLK pin configuration for SJA1105 DSA driver

This series adds support for the PTP_CLK pin on SJA1105 to be configured
via the PTP subsystem, in the "periodic output" and "external timestamp
input" modes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.

On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.

The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
 - When emitting a oneshot pulse, instead of being told when to emit it,
   the switch just does it "now" and tells you later what time it was,
   via the PTPSYNCTS register. [ Incidentally, this is the same register
   that the slave uses to collect the ext_ts timestamp from, too. ]
 - On the sync slave, there is no interrupt mechanism on reception of a
   new extts, and no FIFO to buffer them, because in the foreseen use
   case, software is in control of both the master and the slave pins,
   so it "knows" when there's something to collect.

These 2 problems mean that:
 - We don't support (at least yet) the quirky oneshot mode exposed by
   the hardware, just normal periodic output.
 - We abuse the hardware a little bit when we expose generic extts.
   Because there's no interrupt mechanism, we need to poll at double the
   frequency we expect to receive a pulse. Currently that means a
   non-configurable "twice a second".
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.

Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.

These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.

The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.

This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: NLogan Magee <mageelog@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Dejin Zheng says:

====================
introduce read_poll_timeout

This patch sets is introduce read_poll_timeout macro, it is an extension
of readx_poll_timeout macro. the accessor function op just supports only
one parameter in the readx_poll_timeout macro, but this macro can
supports multiple variable parameters for it. so functions like
phy_read(struct phy_device *phydev, u32 regnum) and
phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
use this poll timeout framework.

the first patch introduce read_poll_timeout macro, and the second patch
redefined readx_poll_timeout macro by read_poll_timeout(), and the other
patches are examples using read_poll_timeout macro.

v6 -> v7:
	- add a parameter to supports that it can sleep some time
	  before read operation in read_poll_timeout macro.
	- add prefix with double underscores for some variable to avoid
	  any variable re-declaration or shadowing in patch 3 and patch
	  7.
v5 -> v6:
	- add some check to keep the code more similar in patch 8
v4 -> v5:
	- add some msleep() before call phy_read_mmd_poll_timeout() to
	  keep the code more similar in patch 6 and patch 9.
	- add a patch of drop by v4, it can add msleep before call
	  phy_read_poll_timeout() to keep the code more similar.
v3 -> v4:
	- add 3 examples of using new functions.
	- deal with precedence issues for parameter cond.
	- drop a patch about phy_poll_reset() function.
v2 -> v3:
	- modify the parameter order of newly added functions.
	  phy_read_mmd_poll_timeout(val, cond, sleep_us, timeout_us, \
				     phydev, devaddr, regnum)
				||
				\/
	  phy_read_mmd_poll_timeout(phydev, devaddr regnum, val, cond, \
				    sleep_us, timeout_us)

	  phy_read_poll_timeout(val, cond, sleep_us, timeout_us, \
				phydev, regnum)
				||
				\/
	  phy_read_poll_timeout(phydev, regnum, val, cond, sleep_us, \
				timeout_us)
v1 -> v2:
	- passed a phydev, device address and a reg to replace args...
	  parameter in phy_read_mmd_poll_timeout() by Andrew Lunn 's
	  suggestion in patch 3. Andrew Lunn <andrew@lunn.ch>, Thanks
	  very much for your help!
	- also in patch 3, handle phy_read_mmd return an error(the return
	  value < 0) in phy_read_mmd_poll_timeout(). Thanks Andrew
	  again.
	- in patch 6, pass a phydev and a reg to replace args...
	  parameter in phy_read_poll_timeout(), and also handle the
	  phy_read() function's return error.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it is sometimes necessary to poll a phy register by phy_read()
function until its value satisfies some condition. introduce
phy_read_poll_timeout() macros that do this.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it is sometimes necessary to poll a phy register by phy_read_mmd()
function until its value satisfies some condition. introduce
phy_read_mmd_poll_timeout() macros that do this.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

redefined readx_poll_timeout macro by read_poll_timeout to
simplify the code.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this macro is an extension of readx_poll_timeout macro. the accessor
function op just supports only one parameter in the readx_poll_timeout
macro, but this macro can supports multiple variable parameters for
it. so functions like phy_read(struct phy_device *phydev, u32 regnum)
and phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
also use this poll timeout core. and also expand it can sleep some time
before read operation.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: NDavid Laight <david.laight@aculab.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
 variable tail set but not used [-Wunused-but-set-variable]

It's not used since commit 4863dea3("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZheng zengkai <zhengzengkai@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
devlink: Preparations for trap policers support

This patch set prepares the code for devlink-trap policer support in a
follow-up patch set [1][2]. No functional changes intended.

Policers are going to be added as attributes of packet trap groups,
which are entities used to aggregate logically related packet traps.
This will allow users, for example, to limit all the packets that
encountered an exception during routing to 10Kpps.

However, currently, device drivers register their packet trap groups
implicitly when they register their packet traps via
devlink_traps_register(). This makes it difficult to pass additional
attributes for the groups. For example, the policer bound to the group.

Therefore, this patch set converts device drivers to explicitly register
their packet trap groups. This will later allow these drivers to
register the group with additional attributes, if any.
====================
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.

Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that drivers explicitly register their supported packet trap groups
there is no for devlink to create them on-demand and destroy them when
their reference count reaches zero.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, packet trap groups are implicitly registered by drivers upon
packet trap registration. When the traps are registered, each is
associated with a group and the group is created by devlink, if it does
not exist already.

This makes it difficult for drivers to pass additional attributes for
the groups.

Therefore, as a preparation for future patches that require passing
additional group attributes, add an API to explicitly register /
unregister these groups.

Next patches will convert existing drivers to use this API.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: improvements for scheduled task handling

This series includes some improvements for handling of scheduled tasks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Factor out setting GPHY 10M to new helper rtl8168g_enable_gphy_10m.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-03-21

Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.

This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.

Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>