MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Updated the error log as suggested by Imre
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.

Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly

v2: Address review comments by Daniel
    - Check if DPLL is enabled rather than checking pipe output type
    - set adjusted_mode->flags to 0 in compute_config rather than using
      pipe_config->quirks
    - Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
    - updated dpll_hw_state correctly
    - Updated commit message and title

v3: Address review comments by Imre
    - Proper masking of P1, M1 fields while computing divisors
    - assert in case of bpp mismatch
    - guard for divide by 0 while computing pclk
    - Use ARRAY_SIZE instead of direct calculation
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This driver makes use of the generic panel information from the VBT.
Panel information is classified into two - panel configuration and panel
power sequence which is unique to each panel. The generic driver uses the
panel configuration and sequence parsed from VBT block #52 and #53

v2: Address review comments by Jani
    - Move all of the things in driver c file from header
    - Make all functions static
    - Make use of video/mipi_display.c instead of redefining
    - Null checks during sequence execution

v3: Address review comments by Damien
    - Rename the panel driver file as intel_dsi_panel_vbt.c
    - Fix style changes as suggested
    - Correct comments for lp->hs and hs->lp count calculations
    - General updating comments to have more clarity
    - using max() instead of ternary operator
    - Fix names (ui_num, ui_den) while using UI in calculations
    - compute max of lp_to_hs switch and hs_to_lp switch while computing
      hs_lp_switch_count
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added as generic parameters which will be initialized in the panel
driver and are specific to panels.

Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In preparation for Generic driver
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.

This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels

v2: Mask away the port_bits before use
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Basically ULPS handling during enable/disable has been moved to
pre_enable and post_disable phases. PLL and panel power disable
also has been moved to post_disable phase. The ULPS entry/exit
sequneces as suggested by HW team is as follows -

During enable time -
set DEVICE_READY --> Clear DEVICE_READY --> set DEVICE_READY

And during disable time to flush all FIFOs -
set ENTER_SLEEP --> EXIT_SLEEP --> ENTER_SLEEP

Also during disbale sequnece sub-encoder disable is moved to the end
after port is disabled.

v2: Based on comments from Ville
    - Detailed epxlaination in the commit messgae
    - Moved parameter changes out into another patch
    - Backlight enabling will be a new patch

v3: Updated as per Jani's comments
    - Removed the I915_WRITE_BITS as it is not needed
    - Moved panel_reset and send_otp_cmds hooks to dsi_pre_enable
    - Moved disable_panel_power hook to dsi_post_disable
    - Replace hardcoding with AFE_LATCHOUT

v4: Make intel_dsi_device_ready and intel_dsi_clear_device_ready static
Signed-off-by: NYogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some panels require one time programming if they do not contain their
own eeprom for basic register initialization. The sequence is

Panel Reset --> Send OTP --> Enable Pixel Stream --> Enable the panel

v2: Based on review comments from Jani and Ville
    - Updated the commit message with more details
    - Move the new parameters out of this patch
Signed-off-by: NYogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2:
 - Grab dpio_lock mutex in vlv_enable_dsi_pll().
 - Add and call vlv_disable_dsi_pll().

v3: Mostly based on Ville's review comments.
 - Only pipe A has DSI PLL lock bit.
 - Add more of CCK REG bit definitions for DSI PLL.
 - Make tables static.
 - Move clock gating out of the clock calculation functions.
 - DSI PLL LDO power gating.
 - Put alternative MNP from table calc behind #ifdef.

v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: Nymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The sub-encoder model is copied from DVO.

v2: Add attached_connector to struct intel_dsi.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>