Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller
Signed-off-by: NAdrian Alonso <aalonso@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fix system chrash caused by groups whose number is smaller than the number
of groups of the last pinctl instance which is not initialized.

iMX7D supports two iomux controllers (iomuxc-lpsr and iomuxc) on probing
the second instance (iomuxc) the chrash below occurs.

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.2.0-next-20150901-00006-gebfa43c (aalonso@bluefly)
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7)
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasin instruction cache
[    0.000000] Machine model: Freescale i.MX7 SabreSD Board
[    0.661012] [<802a6cb0>] (strcmp) from [<802cc80c>] (imx_dt_node_to_map+0x58/0x208)
[    0.668879] [<802cc80c>] (imx_dt_node_to_map) from [<802cbe24>] (pinctrl_dt_to_map+0x174/0x2b0)
[    0.677654] [<802cbe24>] (pinctrl_dt_to_map) from [<802c8f18>] (pinctrl_get+0x100/0x424)
[    0.685878] [<802c8f18>] (pinctrl_get) from [<802c9510>] (pinctrl_register+0x26c/0x480)
[    0.694104] [<802c9510>] (pinctrl_register) from [<802ccf3c>] (imx_pinctrl_probe+0x580/0x6e8)
[    0.702706] [<802ccf3c>] (imx_pinctrl_probe) from [<80351b58>] (platform_drv_probe+0x44/0xa4)
[    0.711455] [<80351b58>] (platform_drv_probe) from [<803503ec>] (driver_probe_device+0x174/0x2b4)
[    0.720405] [<803503ec>] (driver_probe_device) from [<803505fc>] (__driver_attach+0x8c/0x90)
[    0.728982] [<803505fc>] (__driver_attach) from [<8034e930>] (bus_for_each_dev+0x6c/0xa0)
[    0.737381] [<8034e930>] (bus_for_each_dev) from [<8034fb88>] (bus_add_driver+0x148/0x1f0)
[    0.745804] [<8034fb88>] (bus_add_driver) from [<80350c00>] (driver_register+0x78/0xf8)
[    0.753880] [<80350c00>] (driver_register) from [<800097d0>] (do_one_initcall+0x8c/0x1d4)
[    0.762282] [<800097d0>] (do_one_initcall) from [<80987dac>] (kernel_init_freeable+0x144/0x1e4)
[    0.771061] [<80987dac>] (kernel_init_freeable) from [<806d9c7c>] (kernel_init+0x8/0xe8)
[    0.779285] [<806d9c7c>] (kernel_init) from [<8000f628>] (ret_from_fork+0x14/0x2c)
[    0.786981] Code: e3520000 e5e32001 1afffffb e12fff1e (e4d03001)
Signed-off-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NAdrian Alonso <aalonso@freescale.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Allow GPIOs to be configured as wakeup sources. When going to suspend,
disable all GPIO irqs excepting the one configured as wakeup sources.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.
Signed-off-by: NVishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add SD card pinmux settings for PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXstream2, and PH1-LD6b SoCs.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It's not needed an is just creating a null statement, so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It's not needed an is just creating a null statement, so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NHongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It's not needed an is just creating a null statement, so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It's not needed an is just creating a null statement, so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

They aren't needed and are just creating null statements so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

They aren't needed and are just creating null statements so remove it.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Merge branch 'sh-pfc-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

This patch adds EthernetAVB

Based on a much lager patch by Takeshi Kihara which was
originally posted by Kuninori Morimoto.
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: extracted from a larger patch;
        corrected swapped {MATCH,CAPTURE_A} pins]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

This patch adds SCIF0/1/2/3/4/5
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
[Morimoto-san: Updated]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Add PFC base support for the R8A7795 SoC.
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
[Morimoto-san: updated]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, all PINMUX_IPSR_MODSEL_DATA() are replased to PINMUX_IPSR_MSEL()
Let's remove unused PINMUX_IPSR_MODSEL_DATA()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.

Current PFC driver is very difficult to read, because macro names are
using different length.

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.

Current PFC driver is very difficult to read, because macro names are
using different length.

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.

Current PFC driver is very difficult to read, because macro names are
using different length.

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.

Current PFC driver is very difficult to read, because macro names are
using different length.

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now, PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA() are same.

Current PFC driver is very difficult to read, because macro names are
using different length.

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can use PINMUX_IPSR_MSEL() instead
of PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

The difference between PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA()
are FN_xxx order, and PINMUX_IPSR_MSEL() is used only from r8a7778.
Now it r8a7778 works correctly with PINMUX_IPSR_MODSEL_DATA() order.
This means we can merge PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA().

Current PFC driver is very difficult to read, because macro names are
using different length. Especially PINMUX_IPSR_MODSEL_DATA() is well
used macro

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
	PINMUX_IPSR_MODSEL_DATA(ipsr, ...)

It can be readable if we can merge
PINMUX_IPSR_MSEL() and PINMUX_IPSR_MODSEL_DATA()

	PINMUX_IPSR_NOGP(ispr, ...)
	PINMUX_IPSR_DATA(ipsr, ...)
	PINMUX_IPSR_NOGM(ispr, ...)
	PINMUX_IPSR_NOFN(ipsr, ...)
	PINMUX_IPSR_MSEL(ipsr, ...)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Now that all ARM-based Renesas SoCs use multiplatform kernels only the
hardcoded IRQ numbers can be dropped as they're dynamically allocated.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_LEGACY.

Move the legacy code to do the non-DT mapping between GPIOs and pins
inside the existing #ifdef CONFIG_SUPERH section.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

When using serial port SCIFB1_B, transmit works, but nothing is
received.

Receive fails because the SCIFB1_SCK_B settings configure the wrong
value for the sel_scifb1 field in the Module Select Register (MOD_SEL),
due to an ambiguity in the R-Car M2-W and M2-N datasheets.

Tested on r8a7791/koelsch using pins 53 (TXD) and 72 (RXD) on EXIO
Connector A.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

SCIF0 on R-Car E2 does not have an SCK pin.

"SCIF_CLK" is the (H)SCIF baud rate generation clock pin, which is not
yet supported.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Legacy function GPIOs are no longer used on ARM since commit
a27c5cd1 ("sh-pfc: sh73a0: Remove function GPIOs").
Extract its setup code into a separate function, and make all function
GPIO related code and data depend on CONFIG_SUPERH.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

gpio_chip.free() is optional, and can just be left unimplemented.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

On platforms where the PFC/GPIO controller is instantiated from DT, the
mapping between GPIOs and pins is set up using the "gpio-ranges"
property in DT.

Hence stop setting up the mapping from C code on DT platforms.
This code is still used for SH or ARM-legacy platforms.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>

The mediatek pinctrl driver uses the BIT() macro instead of open
coding 1 << n in all but one place. Replace this occurrence with
the BIT() macro for consistency.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Many parts of pinctrl rk3036 are similar to rk2928's.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add pio4 controller node to enable pinmux and gpio.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add an entry for the Atmel PIO4 controller driver.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add documentation for the Atmel PIO4 controller introduced with SAMA5D2
chip family.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add a pinctrl/gpio driver for Atmel PIO4 controller available on SAMA5D2
chip family.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull ARM fixes from Russell King:
 "Three fixes and a resulting cleanup for -rc2:

   - Andre Przywara reported that he was seeing a warning with the new
     cast inside DMA_ERROR_CODE's definition, and fixed the incorrect
     use.

   - Doug Anderson noticed that kgdb causes a "scheduling while atomic"
     bug.

   - OMAP5 folk noticed that their Thumb-2 compiled X servers crashed
     when enabling support to cover ARMv6 CPUs due to a kernel bug
     leaking some conditional context into the signal handler"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8425/1: kgdb: Don't try to stop the machine when setting breakpoints
  ARM: 8437/1: dma-mapping: fix build warning with new DMA_ERROR_CODE definition
  ARM: get rid of needless #if in signal handling code
  ARM: fix Thumb2 signal handling when ARMv6 is enabled