Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.

I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.

CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing validate_addr hook.
Signed-off-by: NDenis Kirjanov <kirjanov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet
MAC IP cores.
Signed-off-by: NKristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduces CPU utilization significantly with sendfile for example.
Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes D-Link DGE-550T PCI ID (1186:4000) from the ipg
driver. The ipg driver is for IP2000-based cards and the DGE-550T is
a DL2000-based card. The driver loads and works for a few moments, but
once a real workload is applied it stops operating. The ipg driver
claimed this ID since it was introduced in 2.6.24 and it's forced many
users to blacklist it.

The correct driver for this hardware is the dl2k driver, which has been
claiming this PCI ID since the 2.4 days.
Signed-off-by: NJeff Mahoney <jeffm@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Alexey Dobriyan:

--------------------
setkey now takes several seconds to run this simple script
and it spits "recv: Resource temporarily unavailable" messages.

#!/usr/sbin/setkey -f
flush;
spdflush;

add A B ipcomp 44 -m tunnel -C deflate;
add B A ipcomp 45 -m tunnel -C deflate;

spdadd A B any -P in ipsec
        ipcomp/tunnel/192.168.1.2-192.168.1.3/use;
spdadd B A any -P out ipsec
        ipcomp/tunnel/192.168.1.3-192.168.1.2/use;
--------------------

Obviously applications want the events even when the table
is empty.  So we cannot make this behavioral change.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds half-duplex specific setup code (taken from SiS own GPL driver).
Without those, half-duplex connections are very unreliable, often
working on small transfers and failing after a while.
Signed-off-by: NRiccardo Ghetta <birrachiara@tin.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The n-tuple list should be flushed if and only if the ETH_RESET_FILTER
flag is set and the driver is able to reset filtering/flow direction
hardware without also resetting a component whose flag is not set.
This test is best left to the driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updated release version and date: 1.52.1-6 and 2010/02/16
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to the new firmware version (5.2.13).
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware version (5.2.13).
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Use the last unicast entry in CAM in bnx2x_test_int(). Relevant for 57710 only.

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Do not allow enabling LRO if disable_tpa=1.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: clean up MCP state in case of error in bnx2x_init_hw().

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix: Properly release allocated MSI-X/MSI vectors if ifup failed
due to lack of memory.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert from:
	if (netif_msg_<foo>(priv))
		dev_<level>(dev...
to
	netif_<level>(priv, foo, dev...

Also convert a few:

	if (i < REG_TIMEOUT) {
		etc...
		return ret;
       }
to
	if (i >= REG_TIMEOUT)
		goto fail;
	etc...
	return ret;
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These macros are too similar to the dev_<level> equivalents
but take a usbnet * argument.  Convert them to the recently
introduced netdev_<level> macros and remove the old macros.

The old macros had "\n" appended to the format string.
Add the "\n" to the converted uses.

Some existing uses of the dev<foo> macros in cdc_eem.c
probably mistakenly had trailing "\n".  No "\n" added there.

Fix net1080 this/other log message inversion.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flush compl (compl with numfrags == 0; no data) is rcvd
from hw to indicate completion of RXQ destory operation. Fix
the RX path to not process it as RX data.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an MCC cmd is issued (via a netdev/ethtool op)
while the device is not open, the MCC CQ gets processed but the EQ
is not processed (as isr is not registered.) This can cause the EQ
to become full. So, while the device is not open, CQ must not be re-armed
to prevent EQ entries.
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce unlikely() for skb alloc failure and vlanf checks...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some servers we see the cleaning of the RX queue finish before all
the loopback packets are sent out.  This delay allows the queues to
settle before checking for successful completion.
Also, delay completion so link has time to come back up.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use local copy of current mac address when initializing.  In bonding
testing we saw cases where dev_addr was out of data causing failover
errors.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was found with pings that were large enough to span multiple rx
buffers.  The split frame logic handles this case nicely.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A userland command to set the LLTEMAC MAC address,
i.e. "ifconfig eth0 hw addr xx:yy:zz:pp:dd:qq",
results in a device address of 00:01:xx:yy:zz:pp.
Correct this.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LLTEMAC V1 cores place only received packet length in the app4 word.
V2 cores place additional information in app4.
Mask out the additional information when retrieving the packet length.
Signed-off-by: NSteven J. Magnani <steve@digidescorp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduced a new function to do the mc list processing, makes code
clearer after transition.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kasprintf() makes code smaller.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2eff25c1
(netfilter: xt_hashlimit: fix race condition and simplify locking)
added a mutex deadlock :
htable_create() is called with hashlimit_mutex already locked
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The net being checked there is dev_net(dev) and thus this if
is always false.

Fits both net and net-next trees.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This updates the tx DMA mapping error handling code to
resemble e1000e/ixgbe.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change simplifies the code by setting RX_PTHRESH to 8 for
all devices, as it was unlikely that there was any advantage to
set it at 16 for earlier cards. Additionally TX_WTHRESH is
set to 1 for the 82576 NIC to improve performance by enabling
a minimal amount of write combining when writing back descriptors.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that igb_free_q_vectors is reused in
igb_alloc_q_vectors to handle the cleanup instead of unwinding
through the allocations.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In an earlier version of igb_write_mc_addr_list() the vmolr register
was modified. This register is no longer accessed, although the variable
still exists. This patch removes it from the function.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change cleans up some instances where unsigned int and u32
were being used interchangeably, and cleans up hdr_len which
was being set to 0 twice.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves gso_segs into the buffer_info structure to avoid
a possible cache line miss in clean_tx_irq.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

igb_maybe_stop_tx() is extremely small and appears in several spots in
the tx hotpath. This change inlines the function for a possible
performance boost.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a couple statistics registers that are not meant to
be read when in SGMII/serdes mode. This patch adds a check to
verify mode before reading and updating these statistics.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SRRCTL.DROP_EN bit should only be set when we are supporting
multiple queues. This bit is meant to prevent head of line blocking
and is unnecessary in the single queue case.
Signed-off-by: NNicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>