The application of a mask to clear an area of a clause 37 register value
was not properly applied. Update the code to do the proper application
of the mask.
Reported-by: NMarion &amp; Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Weiser says:

====================
sun4i-emac: Fixes for running a big-endian kernel on Cubieboard2

the following patches are what remains to be fixed in order to allow running a
big-endian kernel on the Cubieboard2.

The first patch fixes up endianness problems with DMA descriptors in
the stmmac driver preventing it from working correctly when runnning a
big-endian kernel.

The second patch adds the ability to enable diagnostic messages in the
sun4i-emac driver which were instrumental in finding the problem fixed
by patch number three: Endianness confusion caused by dual-purpose I/O
register usage in sun4i-emac.

All of these have been tested successfully on a Cubieboard2 DualCard.

Changes since v4:
- Rebased to current master
- Removed already applied patches to sunxi-mmc and sunxi-Kconfig

Changes since v3:
- Rebased sunxi-mmc patch against Ulf's mmc.git/next
- Changed Kconfig change to enable big-endian support only for sun7i
  devices

Changes since v2:
- Fixed typo in stmmac patch causing a build failure
- Added sun4i-emac patches

Changes since v1:
- Fixed checkpatch niggles
- Added respective Cc:s
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC EMAC_RX_IO_DATA_REG data register is dual-purpose: On one hand
it is used to move actual packet data off the wire. This will be in
wire-format and accepted as such by higher layers such as IP. Therefore
it is correctly read as-is (i.e. raw) using readsl.

On the other hand it provides metadata about incoming transfers to the
driver such as length and checksum validation status. This data is
little-endian, always and it is interpreted by the driver. Therefore it
needs to be swapped to CPU endianness to make sense to the driver. This
is already done for the "receive header" but not rxhdr.

Read rxhdr using readl in order for sun4i-emac to work correctly when
running a big-endian kernel.
Signed-off-by: NMichael Weiser <michael.weiser@gmx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sun4i-emac has the ability to print a number of diagnostic messages using
dev_dbg depending on message level settings implemented using netif_msg_*
macros. But there's no way to actually enable them.

Add the ability to switch diagnostic messages on using either a module
parameter debug or ethtool -s <netif> msglvl <flags>.
Signed-off-by: NMichael Weiser <michael.weiser@gmx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The stmmac driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes the ethernet
interface not to be initialised correctly when running a big-endian
kernel. Change the descriptors for DMA to use __le32 and ensure they are
suitably swapped before writing. Tested successfully on the
Cubieboard2.
Signed-off-by: NMichael Weiser <michael.weiser@gmx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

draft-ietf-tcpm-dctcp-02 says:

... when the sender receives an indication of congestion
(ECE), the sender SHOULD update cwnd as follows:

         cwnd = cwnd * (1 - DCTCP.Alpha / 2)

So, lets do this and reduce cwnd more smoothly (and faster), as per
current congestion estimate.

Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduced a typo making the driver no longer build, *sigh*.

Fixes: 42469bf5 ("net: bcm63xx_enet: Utilize phy_ethtool_nway_reset")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: Centralize auto-negotation restart

This patch series centralizes how ethtool::nway_reset is implemented
by providing a PHYLIB function which calls into genphy_restart_aneg().

All drivers below are converted to use this new helper function. Some
other have specific requirements that make them not quite suitable for
a straight forward conversion.

There is another patch series which implements ethtool::nway_reset
using the helper function introduced that depends on this patch
series.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NThomas Langer <Thomas.langer@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/vxlan.c: In function ‘vxlan_xmit_one’:
drivers/net/vxlan.c:2141:10: warning: ‘err’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
vxlan: xmit improvements.

Following patch series improves vxlan fast path, removes
duplicate code and simplifies vxlan xmit code path.

v2-v3:
Removed unrelated warning fix from patch 2.
rearranged error handling from patch 3
Fixed stats updates in vxlan route lookup in patch 4

v1-v2:
Fix compilation error when IPv6 support is not enabled.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Existing vxlan xmit function handles two distinct cases.
1. vxlan net device
2. vxlan lwt device.
By seperating initialization these two cases the egress path
looks better.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid code duplicate code for handling RTF_LOCAL routes.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move route sanity check to respective vxlan[4/6]_get_route functions.
This allows us to perform all sanity checks before caching the dst so
that we can avoid these checks on subsequent packets.
This give move accurate metadata information for packet from
fill_metadata_dst().
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vxlan egress path error handling has became complicated, it
need to handle IPv4 and IPv6 tunnel cases.
Earlier patch removes vlan handling from vxlan_build_skb(), so
vxlan_build_skb does not need to free skb and we can simplify
the xmit path by having single error handling for both type of
tunnels.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check the vxlan socket in vxlan6_getroute().
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VxLan device does not have special handling for vlan taging on egress.
Therefore it does not make sense to expose vlan offloading feature.
This patch does not change vxlan functinality.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 850cbadd ("udp: use it's own memory accounting schema")
assumes that the socket proto has memory accounting enabled,
but this is not the case for UDPLITE.
Fix it enabling memory accounting for UDPLITE and performing
fwd allocated memory reclaiming on socket shutdown.
UDP and UDPLITE share now the same memory accounting limits.
Also drop the backlog receive operation, since is no more needed.

Fixes: 850cbadd ("udp: use it's own memory accounting schema")
Reported-by: NAndrei Vagin <avagin@gmail.com>
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
bpf: LRU map

This patch set adds LRU map implementation to the existing BPF map
family.

The first few patches introduce the basic BPF LRU list
implementation.

The later patches introduce the LRU versions of the
existing BPF_MAP_TYPE_LRU_[PERCPU_]HASH maps by leveraging
the BPF LRU list.

v2:
- Added a percpu LRU list option which can be specified as
  a map attribute.

  [Note: percpu LRU list has nothing to do with the map's value]

- Removed the cpu variable from the struct bpf_lru_locallist
  since it is not needed.

- Changed the __bpf_lru_node_move_out to __bpf_lru_node_move_to_free in
  patch 1 to prepare the percpu LRU list in patch 2.

- Moved the test_lru_map under selftests

- Refactored a few things in the test codes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch has some unit tests and a test_lru_dist.

The test_lru_dist reads in the numeric keys from a file.
The files used here are generated by a modified fio-genzipf tool
originated from the fio test suit.  The sample data file can be
found here: https://github.com/iamkafai/bpf-lru

The zipf.* data files have 100k numeric keys and the key is also
ranged from 1 to 100k.

The test_lru_dist outputs the number of unique keys (nr_unique).
F.e. The following means, 61239 of them is unique out of 100k keys.
nr_misses means it cannot be found in the LRU map, so nr_misses
must be >= nr_unique. test_lru_dist also simulates a perfect LRU
map as a comparison:

[root@arch-fb-vm1 ~]# ~/devshare/fb-kernel/linux/samples/bpf/test_lru_dist \
/root/zipf.100k.a1_01.out 4000 1
...
test_parallel_lru_dist (map_type:9 map_flags:0x0):
    task:0 BPF LRU: nr_unique:23093(/100000) nr_misses:31603(/100000)
    task:0 Perfect LRU: nr_unique:23093(/100000 nr_misses:34328(/100000)
....
test_parallel_lru_dist (map_type:9 map_flags:0x2):
    task:0 BPF LRU: nr_unique:23093(/100000) nr_misses:31710(/100000)
    task:0 Perfect LRU: nr_unique:23093(/100000 nr_misses:34328(/100000)

[root@arch-fb-vm1 ~]# ~/devshare/fb-kernel/linux/samples/bpf/test_lru_dist \
/root/zipf.100k.a0_01.out 40000 1
...
test_parallel_lru_dist (map_type:9 map_flags:0x0):
    task:0 BPF LRU: nr_unique:61239(/100000) nr_misses:67054(/100000)
    task:0 Perfect LRU: nr_unique:61239(/100000 nr_misses:66993(/100000)
...
test_parallel_lru_dist (map_type:9 map_flags:0x2):
    task:0 BPF LRU: nr_unique:61239(/100000) nr_misses:67068(/100000)
    task:0 Perfect LRU: nr_unique:61239(/100000 nr_misses:66993(/100000)

LRU map has also been added to map_perf_test:
/* Global LRU */
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 16 $i | awk '{r += $3}END{print r " updates"}'; done
 1 cpus: 2934082 updates
 4 cpus: 7391434 updates
 8 cpus: 6500576 updates

/* Percpu LRU */
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 32 $i | awk '{r += $3}END{print r " updates"}'; done
  1 cpus: 2896553 updates
  4 cpus: 9766395 updates
  8 cpus: 17460553 updates
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a LRU version of the existing BPF_MAP_TYPE_PERCPU_HASH
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a LRU version of the existing BPF_MAP_TYPE_HASH.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor the codes that populate the value
of a htab_elem in a BPF_MAP_TYPE_PERCPU_HASH
typed bpf_map.
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having a common LRU list, this patch allows a
percpu LRU list which can be selected by specifying a map
attribute.  The map attribute will be added in the later
patch.

While the common use case for LRU is #reads >> #updates,
percpu LRU list allows bpf prog to absorb unusual #updates
under pathological case (e.g. external traffic facing machine which
could be under attack).

Each percpu LRU is isolated from each other.  The LRU nodes (including
free nodes) cannot be moved across different LRU Lists.

Here are the update performance comparison between
common LRU list and percpu LRU list (the test code is
at the last patch):

[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 16 $i | awk '{r += $3}END{print r " updates"}'; done
 1 cpus: 2934082 updates
 4 cpus: 7391434 updates
 8 cpus: 6500576 updates

[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 32 $i | awk '{r += $3}END{printr " updates"}'; done
  1 cpus: 2896553 updates
  4 cpus: 9766395 updates
  8 cpus: 17460553 updates
Signed-off-by: NMartin KaFai Lau <kafai@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>