Add support for the Atmel AT91SAM9263-EK board.

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.

These changes are:
      * The system peripheral I/O region we remap has increased from
        0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
      * The increased I/O region forces changes to entry-macro.S and
        debug-macro.S due to ARM's limited immediate offset addressing
        modes.
      * Maximum number of GPIO banks increases to 5.
      * 2 MMC controllers so the board-setup code needs to specify which
        controller it wishes to use when calling at91_add_device_mmc().

Original patch from Nicolas Ferre.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.

The following git commands should be run BEFORE applying this patch:
  git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
  git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix build failure of AT91SAM9260.

The AT91RM9200 ethernet driver (at91_ether.c) stores platform data in a
"struct at91_eth_data" structure, but the AT91SAM9260 (and AT91SAM9263)
ethernet driver (macb.c) [developed on the AVR32 architecture] expects a
"struct eth_platform_data".

Since the platform data of the two drivers is very similar, we continue
to use the "struct at91_eth_data" for all AT91 processors but add a
    #define eth_platform_data      at91_eth_data
in board.h to keep the MACB driver happy.

Original patch by Jan Altenberg.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add PHY IRQ pin definition for AT91SAM9260-EK board.
Signed-off-by: NWojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds support for the Atmel AT91SAM9260-EK board.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch converts the old CONFIG_MTD_PHYSMAP_ options to the new
physmap API by creating a physmap platform device for the NOR flash
found on the Atmel AT91RM9200-DK and AT91RM9200-EK boards.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch makes the AT91 gpio.c support processor-generic (AT91RM9200
and AT91SAM9xxx).  The GPIO controllers supported by a particular AT91
processor are defined in the processor-specific file and are registered
with gpio.c at startup.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch makes the AT91 clock.c support processor-generic (AT91RM9200
and AT91SAM9xxx).  The clocks supported by a particular AT91 processor
are defined in the processor-specific file and are registered with
clock.c at startup.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch updates the support for the Atmel DK and EK boards.

The changes include:
1. Use the new at91_uart_config structure and device registration
functions for the UARTs.
2. Registration of I2C and SPI platform devices.
3. The USB Device pullup line is connected to reset, so multidrive needs
to be enabled on the line.  [Patch from David Brownell].
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

On the Atmel AT91RM9200-DK and -EK boards, a pin is used to control
whether the card socket is used for a DataFlash Card or an MMC/SD card.

We now default to MMC/SD in the configuration files.

(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support for the LED(s) on the AT91RM9200-based boards.

(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

This field is redundent since it must be equal to PHYS_OFFSET anyway.

Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.

This patch is the support for Atmel's DK and EK boards.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>