Add optional function parameters associated with sending SYNACK.
These parameters are not needed after sending SYNACK, and are not
used for retransmission.  Avoids extending struct tcp_request_sock,
and avoids allocating kernel memory.

Also affects DCCP as it uses common struct request_sock_ops,
but this parameter is currently reserved for future use.

Signed-off-by: William.Allen.Simpson@gmail.com
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace pci_alloc_consistent() with dma_alloc_coherent() so that
appropriate GFP flags can be used.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The old code mistakenly zeroed out the upper 32-bit of the DMA address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix code to read the proper iSCSI MAC address for bnx2x devices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to send a HALT command to the firmware to fully shutdown the bnx2x
rings.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Old code was initializing the ring producers using an incorrect I/O
address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle few corner cases in firmware hang detection and recovery:

o Don't mark device state as READY, till handshake with
  firmware is done.
o During probe, if start_firmware fails, restore reference
  count.
o Don't increment refernce count, if start_firmware fails
  during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
  reaches critical limit so that pci remove() doesn't poll on
  this bit.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver maps only some part of the MMIO bar 0 in case of
NX2031. This is sufficient for tx and rx by the driver.
When debug tools need to access resources in
unmapped regions, driver needs to map these on the fly
in order to complete read/write request.
Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device.  This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses.  Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function pointers for 8257x devices are not set.  This is not really a
problem now because there is nothing in the driver that references the
pointers for this particular MAC-family (the appropriate functions are
called directly), but the pointers should be set in case they are used in
the future.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two functions skb_dma_map/unmap are unsafe to use as they cause
problems when packets are cloned and sent to multiple devices while a HW
IOMMU is enabled.  Due to this it is best to remove the code so it is not
used by any other network driver maintainters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.

[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
  code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the skb_dma_map/unmap calls from the igbvf driver due to
the fact that it does not play well with HW IOMMU when combined with
transmitting cloned skbs.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change removes skb_dma_map/unmap calls from the igb driver due to the
fact that the call is incompatible with iommu enabled kernels.  In order to
prevent warnings about using the wrong unmap call I have added a
mapped_as_page value to the buffer_info structure to track if the mapped
region is a page or a buffer.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems.  The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_dma_map is incompatible with HW iommu due to the fact that multiple
mappings can result in different results each time.  For this reason it is
best to just remove use of these function calls.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the use of skb_dma_map from the e1000 driver in order to avoid
issues when HW iommu are in use.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 27fed417 (ip: fix logic of
reverse path filter sysctl) has changed the logic of rp_filter.  The
document about rp_filter is out of date. Now, setting
conf/all/rp_filte with 0 can also enable source validation.

Update the document according to the commit.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2 is failing when a PCI error is detected. The error is the
following:

bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d

This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2 ("PCI: Clear
saved_state after the state has been restored").

Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changed braces position on some statements.
Inserted a space between an "if" keyword and a parenthesis.
Signed-off-by: NRudy Matela <rudy.matela@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must test if user timespec is non-NULL before copying from userpace,
same as sys_recvmmsg().

Commiter note: changed it so that we have just one branch.
Signed-off-by: NJean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both to traverse the entries and to set the msg_len field.

Commiter note: folded two patches and avoided one branch repeating the
compat test.
Signed-off-by: NJean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following warning, when building on 64 bits:

net/sctp/socket.c:2091: warning: large integer implicitly
                        truncated to unsigned type
Signed-off-by: NAndrei Pelinescu-Onciul <andrei@iptel.org>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A small cleanup after last net-2.6 merge into net-next-2.6

As we are going to free skb, no need to set skb->skb_iif or skb->dev
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool_ops.set_settings support to the PS3 gelic network driver.
Allows manual setting of ethernet link speed.
Signed-off-by: NHideyuki Sasaki <xhide@rd.scei.sony.co.jp>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleanup of the gelic driver enumerations:

 o Add some missing commas.
 o Add an Ether port post fix (PS3 currently only supports PORT_0).
 o Add a new enum gelic_lv1_phy to use when interacting with the PHY.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Every time while doing ethtool->get_settings we are accessing
the hardware to get link status and port information.
This is not necessary.  We now use the cached copy for this info
and update it when the link status changes.

From: Suresh R <sureshr@serverengines.com>
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add be_rx_polls to count number of times NAPI called rx poll function.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

port identification/beaconing is failing if device open has not been done.
Fixing it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow only valid ether addresses to be assigned and used for the interface.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

patch to initialize netdev->perm_addr
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

patch to initialize netdev->vlan_features appropriately.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For hardware limit to support TSOV6, just disable this feature
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use the sizeof the pointer to clear the result
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the case for 82577 because it does not support the ability to check
for downshift.  Add case for e1000_phy_bm which can do this.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>