Do not retransmit previously-sent data when a "receiver ready" s-frame
with the "final" flag is received during a move.

The ERTM state machines will resynchronize at the end of a channel
move, and the state machine needs to avoid state changes during a
move.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When operating over BR/EDR, ERTM accounts for the maximum over-the-air
packet size when setting the PDU size.  AMP controllers do not use the
same over-the-air packets, so the PDU size should only be based on the
HCI MTU of the AMP controller.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The L2CAP spec recommends specific retransmit and monitor timeouts for
ERTM channels that are on AMP controllers.  These timeouts are
calculated from the AMP controller's best effort flush timeout.

BR/EDR controllers use the default retransmit and monitor timeouts.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Outgoing ERTM data is queued during a channel move.  The ERTM state
machine is partially reset at the start of a move, and must be
resynchronized with the remote state machine at the end of the move.
Data is not sent so that there are no state transitions between the
partial reset and the resync.

Streaming mode frames are dropped during a move.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

AMP controllers expect to transmit only "complete" ACL frames.  These
frames have both the "start" and "cont" bits set.  AMP does not allow
fragmented ACLs.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Several different actions may be taken when an AMP physical link
becomes available.  A channel being created on an AMP controller must
continue the connection process.  A channel being moved needs to
either send a move request or a move response.  A failed physical link
will revert to using a BR/EDR controller if possible.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The move confirm response concludes the channel move command sequence.
Receipt of this command indicates that data may begin to flow again.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The logical link confirm callback is executed when the AMP controller
completes its logical link setup.  During a channel move, a newly
formed logical link allows a move responder to send a move channel
response.  A move initiator will send a move channel confirm.  A
failed logical link will end the channel move and send an appropriate
response or confirm command indicating a failure.

If the channel is being created on an AMP controller, L2CAP
configuration is completed after the logical link is set up.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The move response command includes a result code indicating
"pending", "success", or "failure" status.  A pending result is
received when the remote address is still setting up a physical link,
and will be followed by success or failure.  On success, logical link
setup will proceed.  On failure, the move is stopped.  The receiver of
a move channel response must always follow up by sending a move
channel confirm command.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

After sending a move channel response, a move responder waits for a
move channel confirm command.  If the received command has a
"confirmed" result the move is proceeding, and "unconfirmed" means the
move has failed and the channel will not change controllers.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Two new states are required to implement channel moves with the ERTM
receive state machine.

The "WAIT_P" state is used by a move responder to wait for a "poll"
flag after a move is completed (success or failure).  "WAIT_F" is
similarly used by a move initiator to wait for a "final" flag when the
move is completing.  In either state, the reqseq value in the
poll/final frame tells the state machine exactly which frame should be
expected next.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

On receipt of a channel move request, the request must be validated
based on the L2CAP mode, connection state, and controller
capabilities.  ERTM channels must have their state machines cleared
and transmission paused while the channel move takes place.

If the channel is being moved to an AMP controller then
an AMP physical link must be prepared.  Moving the channel back to
BR/EDR proceeds immediately.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Processing a move channel request involves getting the channel
structure using the destination channel ID.  Previous code could only
look up using the source channel ID.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Resolves a conflict resolution issue in "Bluetooth: Fix L2CAP coding
style".  The remaining connect and create channel response handler is
renamed to better reflect its use for both response types.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The L2CAP create channel request is very similar to an L2CAP connect
request, but it has an additional parameter for the controller ID.  If
the controller id is 0, the channel is set up on the BR/EDR controller
(just like a connect request).  Using a valid high speed controller ID
will cause the channel to be initially created on that high speed
controller.  While the L2CAP data will be initially routed over the
AMP controller, the L2CAP fixed signaling channel only uses BR/EDR.

When a create channel request is received for a high speed controller,
a pending response is always sent first.  After the high speed
physical and logical links are complete a success response will be
sent.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

An L2CAP channel using high speed continues to be associated with a
BR/EDR l2cap_conn, while also tracking an additional hci_conn
(representing a physical link on a high speed controller) and hci_chan
(representing a logical link).  There may only be one physical link
between two high speed controllers.  Each physical link may contain
several logical links, with each logical link representing a channel
with specific quality of service.

During a channel move, the destination channel id, current move state,
and role (initiator vs. responder) are tracked and used by the channel
move state machine.  The ident value associated with a move request
must also be stored in order to use it in later move responses.

The active channel is stored in local_amp_id.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If BREDR L2CAP chan is deleted and this chan is the channel through
which High Speed traffic is routed to AMP then zero pointer to
the chan in amp_mgr to prevent accessing it.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Do not send EFS Configuration Response for High Speed channel yet.
It will be sent after receiving Logical Link Complete event.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

High Speed hci_conn should always have l2cap_conn associated with it.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Check flags type in switch statement and handle new frame
type ACL_COMPLETE used for High Speed data over AMP.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Use of "__" usually means we need to call the function with a lock held,
which is not the case here.
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When DEFER_SETUP is set defer() will trigger an authorization
request to the userspace.

l2cap_chan_no_defer() is meant to be used when one does not want to
support DEFER_SETUP (A2MP for example).
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This is part of the move the parent socket usage to l2cap_sock.c

The change is safe when it comes to locking, bt_accept_enqueue() is still
protected by the parent socket lock inside the
l2cap_sock_new_connection_cb() code.
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Users that don't implement teardown() should use l2cap_chan_no_teardown()
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

No one was protecting the state set in l2cap_send_disconn_req()
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

l2cap_conn_unreliable() doesn't take the sk lock, so we need to take it
using l2cap_chan_set_err().
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Since we change the Bluetooth core to run in process context we don't need
to use GFP_ATOMIC in many of places we were using it. The we just replace
by GFP_KERNEL.
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Follow the net subsystem coding style
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

L2CAP connect requests and create channel requests share a significant
amount of code.  This change moves common code to a new function.
Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Signed-off-by: NMat Martineau <mathewm@codeaurora.org>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

There are two Flush Timeouts: one is old Flush Timeot Option
which is 2 octets and the second is Flush Timeout inside EFS
which is 4 octets long.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Use function to factor out similar code. For BR/EDR send EFS
Configuration Response immediately, for HS response will be sent
after receiving HCI Logical Link Complete event in the following
patches.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in sprintf and seq_printf
statements.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Instead of old unsafe batostr function use %pMR print specifier
for printing Bluetooth addresses in debug and error statements.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When there is no remote AMP controller found fallback to normal
L2CAP sequence.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Choose which L2CAP connection to establish by checking support
for HS and remote side supported features.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

When releasing L2CAP socket which is in BT_CONFIG state l2cap_chan_close
invokes l2cap_send_disconn_req which cancel delayed works which are only
set in BT_CONNECTED state with l2cap_ertm_init. Add state check before
cancelling those works.

...
[ 9668.574372] [21085] l2cap_sock_release: sock cd065200, sk f073e800
[ 9668.574399] [21085] l2cap_sock_shutdown: sock cd065200, sk f073e800
[ 9668.574411] [21085] l2cap_chan_close: chan f073ec00 state BT_CONFIG sk f073e800
[ 9668.574421] [21085] l2cap_send_disconn_req: chan f073ec00 conn ecc16600
[ 9668.574441] INFO: trying to register non-static key.
[ 9668.574443] the code is fine but needs lockdep annotation.
[ 9668.574446] turning off the locking correctness validator.
[ 9668.574450] Pid: 21085, comm: obex-client Tainted: G           O 3.5.0+ #57
[ 9668.574452] Call Trace:
[ 9668.574463]  [<c10a64b3>] __lock_acquire+0x12e3/0x1700
[ 9668.574468]  [<c10a44fb>] ? trace_hardirqs_on+0xb/0x10
[ 9668.574476]  [<c15e4f60>] ? printk+0x4d/0x4f
[ 9668.574479]  [<c10a6e38>] lock_acquire+0x88/0x130
[ 9668.574487]  [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574491]  [<c1059790>] del_timer_sync+0x50/0xc0
[ 9668.574495]  [<c1059740>] ? try_to_del_timer_sync+0x60/0x60
[ 9668.574515]  [<f8aa1c23>] l2cap_send_disconn_req+0xe3/0x160 [bluetooth]
...
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.

This also makes it clear that it is checking the security of the link.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch changes the struct l2cap_chan and associated code to use
kref api for object refcounting and freeing.
Suggested-by: NAndrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: NJaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: NSyam Sidhardhan <s.syam@samsung.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>