This patch cleans up the logic dealing with link down/up by breaking down the
link detection and up/down events into separate functions - similar to how these
events are handled in other drivers.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to allow for Tx hang checking.  The idea is to provide
more robust debug info in the event of a transmit unit hang. Similar to the
logic in ixgbe.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the ordering of the shutdown path so that we attempt to
shutdown the rings more gracefully. Basically the big changes are that we
shutdown the main Rx filter in the case of Rx and we set the carrier_off
state in the case of Tx so that packets stop being delivered from outside
the driver.  Then we shut down interrupts and NAPI.  Finally we stop the
rings from performing DMA and clean them.  This is a bit more graceful than
the previous path.

CC: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Clean up the setting of vlan_features by enabling all features at once.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support VXLAN receive checksum offload in X550 hardware.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We always identify the PHY in our reset_hw path anyway so there is
no need to do it in get_invariants().  The reason I even noticed this
is that for new hardware (X550em) we don't assign some methods until
later in probe and calling phy.ops.read_reg could lead to a panic.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

My original patch 6a14ee0c "ixgbe: Add X550 support function pointers"
accidental set a default value for this structure member twice.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes couple of issues introduced by
commit 2b509c0c ("ixgbe: cleanup ixgbe_ndo_set_vf_vlan")

- fix setting of the VLAN inside ixgbe_enable_port_vlan()
- disable the "hide VLAN" bit in PFQDE when port VLAN is disabled
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

X550 provides RSS registers for configuring RSS per VF.

This patch introduces ixgbevf_setup_vfmrqc() which uses the VFRETA,
VFRSSRK and VFMRQC registers to configure RSS on X550.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables multiple queues and RSS support for the VF.
Maximum of 2 queues are supported due to available vectors.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_set_sriov_queues() has the logic to allow multiple queues, this patch
just removes the limitation.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up prototypes that should have been defined
as static.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix two cases where variables are being set but not used.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: Krishneil Singh<Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, fm10k_update_xc_addr_pf has an issue where it does not
properly drop the upper-most four bits of the VLAN ID due to type
promotion. Resolve the issue not by masking off the bits, but by
throwing an error if the VLAN ID is out-of-bounds.
Reported-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers

This is used later in this series
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbevf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use first->protocol instead of skb->protocol to get the proper network
protocol.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
ixgbe_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a skb has multiple vlans and it is CHECKSUM_PARTIAL,
igbvf_tx_csum() fails to get the network protocol and checksum related
descriptor fields are not configured correctly because skb->protocol
doesn't show the L3 protocol in this case.

Use vlan_get_protocol() to get the proper network protocol.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't update Tx tail descriptor if queue hasn't been stopped
and we know at least one more skb will be sent right away.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't update Tx tail descriptor if we queue hasn't been stopped and
we know at least one more skb will be sent right away.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 5ac6f91d changed the igb driver to expose a zero (empty) mac
address to the VF on reset rather than a random one.

However, that behavioral change also requires igbvf driver changes
which can be hard especially when we want to talk to proprietary
guest OSs.

Looking at the code previous to the commit in Linux that made igbvf
work with empty mac addresses (8d56b6d5), we can see that on reset
failure the driver will try to generate a new mac address with both
the old and the new code.

Furthermore, ixgbe does send reset failure when it detects an empty
mac address (35055928).

So I think it's safe to make igb behave the same. With this patch I
can successfully run a Windows 8.1 guest with an empty mac address
and an assigned igbvf device that has no mac address set by the host.

If anyone is aware of a guest driver that chokes on NACK returns of
VF RESET commands, please speak up.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on feedback from the hardware team, 100us is too short of a time
to wait for the data path reset to complete and the recommendation is to
increase this timeout to 150us.
Signed-off-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fm10k supports up to 184 bytes of inner+outer headers. Add an initial
check to fail encap offload if these are too large.
Signed-off-by: NJoe Stringer <joestringer@nicira.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The networking core does it for the driver during registration time.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Acked-by: NMatthew Vick <matthew.vick@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i210 device offers a number of special PTP Hardware Clock features on
the Software Defined Pins (SDPs). This patch adds support for two of the
possible functions, namely time stamping external events, and periodic
output signals.

The assignment of PHC functions to the four SDP can be freely chosen by
the user.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i210 device can produce an interrupt on the full second. This
patch allows using this interrupt to generate an internal PPS event
for adjusting the kernel system time.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The time sync related interrupt registers may be manipulated from
different contexts. This patch protects the registers from being
asynchronously changed by the reset function.

Also, the patch removes a misleading comment. The reset function
is disabling a bunch of functions, not enabling them.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code that handles the time sync interrupt is repeated in three
different places. This patch refactors the identical code blocks into
a single helper function.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.

It also cleans up how we clear the descriptor status bits.  Previously they
were zeroed as a part of clearing the hdr_addr.  However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems.  Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared.  As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.

It also cleans up how we clear the descriptor status bits.  Previously they
were zeroed as a part of clearing the hdr_addr.  However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems.  Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared.  As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With the Intel 82527EI (driver: e1000e) there is an issue when running
the ptpd2 program, that leads to a kernel oops.  The reason is here that
in e1000_xmit_frame() a work queue will be scheduled that has not been
initialized in this case.  The work queue "tx_hwstamp_work" will only be
initialized if adapter->flags & FLAG_HAS_HW_TIMESTAMP set.  This check
is missing in e1000_xmit_frame().

The following patch adds the missing check.
Signed-off-by: NMathias Koehrer <mathias.koehrer@etas.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

To be future-proof and for better readability the time comparisons are
modified to use time_after_eq() instead of plain, error-prone math.
Signed-off-by: NAsaf Vertz <asaf.vertz@tandemg.com>
Acked-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump i40e to 1.2.6 and i40evf to 1.2.0 version.

Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32
Signed-off-by: NSravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add parsing and reporting of iSCSI capability for a given device or
function.

Also add support for iSCSI partition type with DCB in NPAR mode.
In this mode it is expected that software would configure both the LAN
and iSCSI traffic classes for the iSCSI partition; whereas all the NIC
type partitions will use LAN TC (TC0) only.
Hence, the patch enables querying of DCB configuration in MFP mode and
configures TCs for iSCSI partition type.

Though NIC type partitions may not have more than 1 TC enabled for them
the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED
will be set/reset on all the partitions based on number of TCs on the
port. This is required as in DCB environment it is expected that all
traffic will be priority tagged.

Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.

Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.

Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add lldp control commands, add oem ocsd and ocbb commands.

Change-ID: I89eba2bd02013d0a44e1ce900559c54bb15f4a66
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix up NVM config read and write data structs.
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add struct size checks to many of the indirect structs and a few
command structs that were left out previously.

Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable firmware LLDP agent for NICs with firmware version lower than
v4.3. Added a message when driver disables the firmware LLDP agent on
such NICs.

Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>