Replace bfa_assert() with bfa_sm_fault() to get unhandled events for
debugging.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear LL_HALT and PSS_ERR bit in the interrupt status register on an IOC crash.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for faster IOC recovery after failure.

Split bfa_ioc.c into three files:
  bfa_ioc.c:    Common code shared between crossbow and catapult ASIC's.

  bfa_ioc_cb.c: Code specific to the crossbow, reg mapping and
                interrupt related routines.

  bfa_ioc_ct.c: Code specific to the catapult, reg mapping and
                interrupt related routines.

Fix to make sure IOC reinitialize's properly on enable request -
update the ioc_fwstate reg with BFI_IOC_FAIL on ioc disable mbox cmd
timeout.

Makefile changes to support the 2 newly added files bfa_ioc_cb.c and
bfa_ioc_ct.c.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfad.c & bfad_drv.h:
  * Created a kernel thread from pci_probe that does the bfad start
    operations after BFA init done on a firmware mismatch.
  * The kernel thread on a fw mismatch waits for an event from IOC
    call back and is woken up from bfa_cb_init() on BFA init success.
  * In normal cases of no firmware mismatch this thread is terminated
    in pci_probe.

bfa_fcs_lport.c, fabric.c, fcs_lport.h & vport.c:
  * Split the lport init to attach time and init time code, so that
    proper config attributes are set after firmware mismatch.

bfa_iocfc.c:
  * Handle an IOC timer issue, where the IOC timer would expire before
    the init completion and send Init fail event to the driver,
    however IOC init continues and completes successfully at the later
    stage. The bfa and driver were not handling this kind of deferred
    init completion.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Brocade CNA currently supports only 190 vports (instead of 191),
since there are only 192 unicast cam entries reserved for FCoE.

Brocade CNA has a total of 256 unicast cam entries (192 FCoE + 64 LL)

192 cam entries = 1 burned in mac + 1 baseport FPMA mac + 190 vport
FPMA macs.

Made changes to the code to support only 190 vports.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Split bfa_fcs_init() into bfa_fcs_attach() and bfa_fcs_init().

Removed empty function definitions in FCS modules

Modified driver to call bfa_fcs_attach() and bfa_fcs_init() as needed.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

 Added a FCS function to be called during driver init, to set the FDMI
 Driver parameter.

fdmi.c: Created a disabled state when fdmi is disabled.

bfad.c:
  * Added fdmi_enable driver parameter.
  * Added support to call bfa_fcs_set_fdmi_param() to initialize fcs
    fdmi setting.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_intr.c:  Enable new halt interrupt in BFA.
bfi_ctreg.h: Expose new halt interrupt bit definition to host.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

bfa_ioc.c:
  - Enable IOC auto-recovery by default.
  - When CNA is in FC mode, return IOC type as FC (not FCoE)

bfa_iocfc.c:
  - Set fcmode before pci initialization/setup.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Clear virtual links was not propagated upwards to bfa from fw.
This resulted in HBA and switch being in an inconsistent state.

So defined a new LPS event for clear virtual link on a vport,
and also now clear virtual link on a baseport, is sent as a
link down event from the fw.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added separate MSI-X module parameters to selectively
enable / disable MSI-X interrupts for both Brocade HBA and CNA's.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

RAID attributes uses scsi_is_sdev_device() to gate some SCSI specific
checking code.  This causes two problems.  Firstly if SCSI == n just
defining scsi_is_sdev_device() to return false might not be enough to
prevent gcc from emitting the code (and thus referring to undefined
symbols), so this needs surrounding with an ifdef.  Secondly, using
scsi_is_sdev_device() when SCSI is either y or m gives a subtle
problem in the m case: raid_attrs must also be m to use the symbol.
Do the usual Kconfig jiggery-pokery to fix this.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Doing CHECK="smatch --two-passes gives:
drivers/scsi/osd/osd_initiator.c +1435 osd_finalize_request warning: assignment to 'ret' was never used

Which is an unchecked possible allocation failure, Fixed.
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Commit e3deec09 incorrectly assumed that the B0 and B1 page lengths were
limited to 32 bytes.  The B0 VPD page length is defined to be 64 bytes
when the device supports thin provisioning.  B1 is always defined to be
64 bytes.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reported-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Added round robin FCF failover on initial or FCF rediscovery FLOGI failure.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Prevent Vport discovery after reg_new_vport completes when physical
  logged in using FDISC.
- Remove fast FCF failover fabric name matching. Allow failover to FCFs
  connected to different fabrics.
- Added fast FCF failover in response to FCF DEAD event on current
  FCF record.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Clear LPFC_DRIVER_ABORTED on FCP command completion.
- Clear exchange busy flag when I/O is aborted and found on aborted list.
- Free sglq when XRI_ABORTED event is processed before release of IOCB.
- Only process iocb as aborted when LPFC_DRIVER_ABORTED is set.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add Logging message for critial errors.
- Remove unused variable from lpfc_nodev_tmo_show
- Update supress_link_up parameter with #define values.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add NULL checks to the pointers for the config_async mailbox
  and dump_wakeup_params mailbox.
- Add code to check return value of lpfc_read_sparams everywhere
  and handle failures appropriately.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This uses the scatter-gather chaining feature of Smart Array
controllers.  32 scatter-gather elements are embedded in the
"command list", and the last element in the list may be marked
as a "chain pointer", and point to an additional block of
scatter gather elements.  The precise number of scatter gather
elements supported is dependent on the particular kind of
Smart Array, and is determined at runtime by querying the
hardware.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The intent of the scan thread was to allow a UNIT ATTENTION/LUN
DATA CHANGED condition encountered in the interrupt handler
to trigger a rescan of devices, which can't be done in interrupt
context.  However, we weren't able to get this to work, due to
multiple such UNIT ATTENTION conditions arriving during the rescan,
during updating of the SCSI mid layer, etc.  There's no way to tell
the devices, "stand still while I scan you!"  Since it doesn't work,
there's no point in having the thread, as the rescan triggered via
ioctl or sysfs can be done without such a thread.
Signed-off-by: NMike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The SCSI status does not need to be shifted.
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adds support for resuming from suspend for IBM VFC devices. We may have
lost an interrupt over the suspend, so we just kick the interrupt handler
to process anything that is outstanding. We expect to find a transport event
indicating we need to reestablish our CRQ.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Adds support for resuming from suspend for IBM VSCSI devices. We may have
lost an interrupt over the suspend, so we just kick the interrupt handler
to process anything that is outstanding. We expect to find a transport event
indicating we need to reestablish our CRQ.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch ensures that we alloc only one EQ
if we are if we are not in msix mode
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes some situations where enough resources were not
avaialable  when targets exceeded a certain limit
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch removes some debug lines which are unnecessary and
also aligns some lines in code
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch cleans up abort handling when TMF is sent
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch fixes a situation where we could call udelay
while holding spin_lock
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch cleans up device and target reset handling
for the driver
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The iscsi_eh_target_reset has been modified to attempt
target reset only. If it fails, then iscsi_eh_session_reset
will be called.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch adds the PCI ID definitions for new adapters based on the next
generation 64 bit IOA PCI interface chip.  New entries have been added to the
ipr_pci_table[] array for the adapters and to the ipr_chip[] array for the new
versions of the chip.

Older entries have been removed for cards that did not ship.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>