For the NCR5380.c core driver, these macros are never used.
If REAL_DMA were to be defined, compilation would fail.

For the atari_NCR5380.c core driver, REAL_DMA is always defined.

Hence these macros are pointless.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Convert compile-time C400_ register mapping to runtime mapping.
This removes the weird negative register offsets and allows adding
additional mappings.

While at it, convert read/write loops into insb/outsb.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

During arbitration and selection, the relevant command is invisible to
exception handlers and can be found only in a pointer on the stack of a
different thread.

When eh_abort_handler can't find a given command, it can't decide whether
that command was completed already or is still in arbitration or selection
phase. But it must return either SUCCESS (e.g. command completed earlier)
or FAILED (could not abort the nexus, try bus reset).

The solution is to make sure all commands belonging to the LLD are always
visible to exception handlers. Add another scsi_cmnd pointer to the
hostdata struct to track the command in arbitration or selection phase.

Replace 'retain_dma_irq' with the new 'selecting' pointer, to bring
atari_NCR5380.c into line with NCR5380.c.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NCR5380_information_transfer() may re-queue a command for autosense,
after calling scsi_eh_prep_cmnd(). This creates several possibilities:

1. Reselection may intervene before the re-queued command gets processed.
   If the reconnected command then undergoes autosense, this causes the
   scsi_eh_save data from the previous command to be overwritten.

2. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
   a new REQUEST SENSE command may arrive. This would be queued ahead
   of any command already undergoing autosense, which means the
   scsi_eh_save data might be restored to the wrong command.

3. After NCR5380_information_transfer() calls scsi_eh_prep_cmnd(),
   eh_abort_handler() may abort the command. But the scsi_eh_save data is
   not discarded, which means the scsi_eh_save data might be incorrectly
   restored to the next REQUEST SENSE command issued.

This patch adds a new autosense list so that commands that are re-queued
because of a CHECK CONDITION result can be kept apart from the REQUEST
SENSE commands that arrive via queuecommand.

This patch also adds a function dedicated to dequeueing and preparing the
next command for processing. By refactoring the main loop in this way,
scsi_eh_save takes place when an autosense command is dequeued rather
than when re-queued.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The NCR5380 drivers have a home-spun linked list implementation for
scsi_cmnd structs that uses cmd->host_scribble as a 'next' pointer. Adopt
the standard list_head data structure and list operations instead. Remove
the eh_abort_handler rather than convert it. Doing the conversion would
only be churn because the existing EH handlers don't work and get replaced
in a subsequent patch.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hostdata struct is now protected by a spin lock so the volatile
qualifiers are redundant. Remove them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replace all H_NO and some HOSTNO macros (both peculiar to atari_NCR5380.c)
with a new dsprintk macro that's more useful and more consistent. The new
macro avoids a lot of boilerplate in new code in subsequent patches. Keep
NCR5380.c in sync. Remaining HOSTNO macros are removed as side-effects
of subsequent patches.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

NCR5380.c presently uses the instance->host_lock spin lock. Convert this
to a new spin lock that protects the NCR5380_hostdata struct.

atari_NCR5380.c previously used local_irq_save/restore() rather than a
spin lock. Convert this to hostdata->lock in irq mode. For SMP platforms,
the interrupt handler now also acquires the spin lock.

This brings all locking in the two core drivers into agreement.

Adding this locking also means that a bunch of volatile qualifiers can be
removed from the members of the NCR5380_hostdata struct. This is done in
a subsequent patch.

Proper locking will allow the abort handler to locate a command being
aborted. This is presently impossible if the abort handler is invoked when
the command has been moved from a queue to a pointer on the stack. (If
eh_abort_handler can't determine whether a command has been completed
or is still being processed then it can't decide whether to return
success or failure.)

The hostdata spin lock is now held when calling NCR5380_select() and
NCR5380_information_transfer(). Where possible, the lock is dropped for
polling and PIO transfers.

Clean up the now-redundant SELECT_ENABLE_REG writes, that used to provide
limited mutual exclusion between information_transfer() and reselect().

Accessing hostdata->connected without data races means taking the lock;
cleanup these accesses.

The new spin lock falls away for m68k and other UP builds, so this should
have little impact there. In the SMP case the new lock should be
uncontested even when the SCSI bus is contested.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove FLAG_DTC3181E. It was used to suppress a final Arbitration Lost
(SEL asserted) test that isn't actually needed. The test was suppressed
because it causes problems for DTC436 and DTC536 chips. It takes place
after the host wins arbitration, so SEL has been asserted. These chips
can't seem to tell whether it was the host or another bus device that
did so.

This questionable final test appears in a flow chart in an early NCR5380
datasheet. It was removed from later documents like the DP5380 datasheet.

By the time this final test takes place, the driver has already tested
the Arbitration Lost bit several times. The first test happens 3 us after
BUS FREE (or longer due to register access delays). The protocol requires
that a device stop signalling within 1.8 us after BUS FREE unless it won
arbitration, in which case it must assert SEL, which is detected 1.2 us
later by the first Arbitration Lost test.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove unused includes (stat.h, signal.h, proc_fs.h) and move includes
needed by the core drivers into the common header (delay.h etc).
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The flags DMA_WORKS_RIGHT, FLAG_NCR53C400 and FLAG_HAS_LAST_BYTE_SENT
all mean the same thing, i.e. the chip is not a 538[01]. (More recent
devices such as the 53C80 have a 'Last Byte Sent' bit in the Target
Command Register as well as other fixes for End-of-DMA errata.)

These flags have no additional meanings since previous cleanup patches
eliminated the NCR53C400 macro, moved g_NCR5380-specific code out of the
core driver and standardized interrupt handling.

Use the FLAG_NO_DMA_FIXUP flag to suppress End-of-DMA errata workarounds,
for those cards and drivers that make use of the TCR_LAST_BYTE_SENT bit.
Remove the old flags.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The complex main_running/queue_main mechanism is peculiar to
atari_NCR5380.c. It isn't SMP safe and offers little value given that
the work queue already offers concurrency management. Remove this
complexity to bring atari_NCR5380.c closer to NCR5380.c.

It is not a good idea to call the information transfer state machine from
queuecommand because, according to Documentation/scsi/scsi_mid_low_api.txt
that could happen in soft irq context. Fix this.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Each host instance now has it's own work queue so the main() work item can
sleep when necessary. That means we can use a simple work item rather than
a delayed work item. This brings NCR5380.c closer to atari_NCR5380.c.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_NCR5380.c and NCR5380.c core drivers differ in their handling of
target disconnection. This is partly because atari_NCR5380.c had all of
the polling and sleeping removed to become entirely interrupt-driven, and
it is partly because of damage done to NCR5380.c after atari_NCR5380.c was
forked. See commit 37cd23b44929 ("Linux 2.1.105") in history/history.git.

The polling changes that were made in v2.1.105 are questionable at best:
if REQ is not already asserted when NCR5380_transfer_pio() is invoked, and
if the expected phase is DATA IN or DATA OUT, the function will schedule
main() to execute after USLEEP_SLEEP jiffies and then return. The problems
here are the expected REQ timing and the sleep interval*. Avoid this issue
by using NCR5380_poll_politely() instead of scheduling main().

The atari_NCR5380.c core driver requires the use of the chip interrupt and
always permits target disconnection. It sets the cmd->device->disconnect
flag when a device disconnects, but never tests this flag.

The NCR5380.c core driver permits disconnection only when
instance->irq != NO_IRQ. It sets the cmd->device->disconnect flag when
a device disconnects and it tests this flag in a couple of places:

1. During NCR5380_information_transfer(), following COMMAND OUT phase,
   if !cmd->device->disconnect, the initiator will take a guess as to
   whether or not the target will then choose to go to MESSAGE IN phase
   and disconnect. If the driver guesses "yes", it will schedule main()
   to execute after USLEEP_SLEEP jiffies and then return there.

   Unfortunately the driver may guess "yes" even after it has denied
   the target the disconnection privilege. When the target does not
   disconnect, the sleep can be beneficial, assuming the sleep interval
   is appropriate (mostly it is not*).

   And even if the driver guesses "yes" correctly, and the target would
   then disconnect, the driver still has to go through the MESSAGE IN
   phase in order to get to BUS FREE phase. The main loop can do nothing
   useful until BUS FREE, and sleeping just delays the phase transition.

2. If !cmd->device->disconnect and REQ is not already asserted when
   NCR5380_information_transfer() is invoked, the function polls for REQ
   for USLEEP_POLL jiffies. If REQ is not asserted, it then schedules
   main() to execute after USLEEP_SLEEP jiffies and returns.

   The idea is apparently to yeild the CPU while waiting for REQ.
   This is conditional upon !cmd->device->disconnect, but there seems
   to be no rhyme or reason for that. For example, the flag may be
   unset because disconnection privilege was denied because the driver
   has no IRQ. Or the flag may be unset because the device has never
   needed to disconnect before. Or if the flag is set, disconnection
   may have no relevance to the present bus phase.

Another deficiency of the existing algorithm is as follows. When the
driver has no IRQ, it prevents disconnection, and generally polls and
sleeps more than it would normally. Now, if the driver is going to poll
anyway, why not allow the target to disconnect? That way the driver can do
something useful with the bus instead of polling unproductively!

Avoid this pointless latency, complexity and guesswork by using
NCR5380_poll_politely() instead of scheduling main().

* For g_NCR5380, the time intervals for USLEEP_SLEEP and USLEEP_POLL are
  200 ms and 10 ms, respectively. They are 20 ms and 200 ms respectively
  for the other NCR5380 drivers. There doesn't seem to be any reason for
  this discrepancy. The timing seems to have no relation to the type of
  adapter. Bizarrely, the timing in g_NCR5380 seems to relate only to one
  particular type of target device. This patch attempts to solve the
  problem for all NCR5380 drivers and all target devices.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Linux v2.1.105 changed the algorithm for polling for the BSY signal
in NCR5380_select() and NCR5380_main().

Presently, this code has a bug. Back then, NCR5380_set_timer(hostdata, 1)
meant reschedule main() after sleeping for 10 ms. Repeated 25 times this
provided the recommended 250 ms selection time-out delay. This got broken
when HZ became configurable.

We could fix this but there's no need to reschedule the main loop. This
BSY polling presently happens when the NCR5380_main() work queue item
calls NCR5380_select(), which in turn schedules NCR5380_main(), which
calls NCR5380_select() again, and so on.

This algorithm is a deviation from the simpler one in atari_NCR5380.c.
The extra complexity and state is pointless. There's no reason to
stop selection half-way and return to to the main loop when the main
loop can do nothing useful until selection completes.

So just poll for BSY. We can sleep while polling now that we have a
suitable workqueue.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When in process context, sleep during polling if doing so won't add
significant latency. In interrupt context or if the lock is held, poll
briefly then give up. Keep both core drivers in sync.

Calibrate busy-wait iterations to allow for variation in chip register
access times between different 5380 hardware implementations.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allocate a work queue that will permit busy waiting and sleeping. This
means NCR5380_init() can potentially fail, so add this error path.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the restart_select and targets_present variables introduced in
Linux v1.1.38. The former was used only for a questionable debug printk
and the latter "so we can call a select failure a retryable condition".
Well, retrying select failure in general is a different problem to a
target that doesn't assert BSY. We need to handle these two cases
differently; the latter case can be left to the SCSI ML.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The aborted flag was introduced in v1.1.38 but never used. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.

Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.

Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().

This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.

The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch splits the NCR5380_init() function into two parts, similar
to the scheme used with atari_NCR5380.c. This avoids two problems.

Firstly, NCR5380_init() may perform a bus reset, which would cause the
chip to assert IRQ. The chip is unable to mask its bus reset interrupt.
Drivers can't call request_irq() before calling NCR5380_init(), because
initialization must happen before the interrupt handler executes. If
driver initialization causes an interrupt it may be problematic on some
platforms. To avoid that, first move the bus reset code into
NCR5380_maybe_reset_bus().

Secondly, NCR5380_init() contains some board-specific interrupt setup code
for the NCR53C400 that does not belong in the core driver. In moving this
code, better not re-order interrupt initialization and bus reset. Again,
the solution is to move the bus reset code into NCR5380_maybe_reset_bus().
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ASM macro is never defined. rtrc in pas16.c is not used.
NCR5380_map_config, do_NCR5380_intr, do_t128_intr and do_pas16_intr
are unused. NCR_NOT_SET harms readability. Remove them.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Unlike NCR5380.c, the atari_NCR5380.c core driver is limited to a single
instance because co-routine state is stored globally.

Fix this by removing the static scsi host pointer. For the co-routine,
obtain this pointer from the work_struct pointer instead. For the interrupt
handler, obtain it from the dev_id argument.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The atari_NCR5380.c core driver keeps some per-host data in a static
variable which limits the driver to a single instance. Fix this by moving
TagAlloc to the hostdata struct.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The static variable setup_use_tagged_queuing is declared in mac_scsi.c,
sun3_scsi.c and atari_scsi.c and doesn't belong in the core driver.
None of the other NCR5380 drivers suffer from this layering issue which
makes merging the core drivers more difficult and will likely hinder plans
for future use of platform data to configure the driver.

Replace the static variable with a host flag. This way it can be reported
along with the other flags.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make the atari_NCR5380.c core driver usable by sun3_scsi, mac_scsi and
others by moving some of the Falcon-specific code out of the core driver:
!IS_A_TT, atari_read_overruns and falcon_dont_release. Replace these with
hostdata variables and flags. FLAG_CHECK_LAST_BYTE_SENT is unused in
atari_NCR5380.c so don't set it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Convert Scsi_Cmnd to struct scsi_cmnd and drop the #include "scsi.h".
The sun3_NCR5380.c core driver already uses struct scsi_cmnd so converting
the other core drivers reduces the diff which makes them easier to unify.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The *_RELEASE macros don't tell me anything. In some cases the version in
the macro contradicts the version in the comments. Anyway, the Linux kernel
version is sufficient information. Remove these macros to improve readability.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Static variables from dtc.c and pas16.c should not appear in the core
NCR5380.c driver. Aside from being a layering issue this worsens the
divergence between the three core driver variants (atari_NCR5380.c and
sun3_NCR5380.c don't support PSEUDO_DMA) and it can mean multiple hosts
share the same counters.

Fix this by making the pseudo DMA spin counters in the core more generic.
This also avoids the abuse of the {DTC,PAS16}_PUBLIC_RELEASE macros, so
they can be removed.

oak.c doesn't use PDMA and hence it doesn't use the counters and hence it
needs no write_info() method. Remove it.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

If the host->info() method is not set, then host->name is used by default.
For atari_scsi, that is exactly the same text. So remove the redundant
info() method. Keep sun3_scsi.c in line with atari_scsi.

Some NCR5380 drivers return an empty string from the info() method
(arm/cumana_1.c arm/oak.c mac_scsi.c) while other drivers use the default
(dmx3191d dtc.c g_NCR5380.c pas16.c t128.c).

Implement a common info() method to replace a lot of duplicated code which
the various drivers use to announce the same information.

This replaces most of the (deprecated) show_info() output and all of the
NCR5380_print_info() output. This also eliminates a bunch of code in
g_NCR5380 which just duplicates functionality in the core driver.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The NCR5380_STATS option is only enabled by g_NCR5380 yet it adds
clutter to all three core drivers. The atari_NCR5380.c and sun3_NCR5380.c
core drivers have a slightly different implementation of the
NCR5380_STATS option.

Out of all ten NCR5380 drivers, only one of them (g_NCR5380) actually
has the code to report on the collected stats. Aside from being unreadable,
that code seems to be broken because there's no initialization of timebase.
sun3_NCR5380.c and atari_NCR5380.c have the timebase initialization but
lack the code to report the stats.

Remove all of this code to improve readability and reduce divergence
between the three core drivers.

This patch and the next one completely eliminate the PRINTP and ANDP
pre-processor abuse.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Oak scsi doesn't use any IRQ, but it sets irq = IRQ_NONE rather than
SCSI_IRQ_NONE. Problem is, the core NCR5380 driver expects SCSI_IRQ_NONE
if it is to issue IDENTIFY commands that prevent target disconnection.
And, as Geert points out, IRQ_NONE is part of enum irqreturn.

Other drivers, when they can't get an IRQ or can't use one, will set
host->irq = SCSI_IRQ_NONE (that is, 255). But when they exit they will
attempt to free IRQ 255 which was never requested.

Fix these bugs by using NO_IRQ in place of SCSI_IRQ_NONE and IRQ_NONE.
That means IRQ 0 is no longer probed by ISA drivers but I don't think
this matters.

Setting IRQ = 255 for these ISA drivers is understood to mean no IRQ.
This remains supported so as to avoid breaking existing ISA setups (which
can be difficult to get working) and because existing documentation
(SANE, TLDP etc) describes this usage for the ISA NCR5380 driver options.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Every NCR5380 driver sets AUTOSENSE so it need not be optional (and the
mid-layer expects it). Remove this redundant macro to improve readability.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Both atari_NCR5380.c and sun3_NCR5380.c core drivers #undef TAG_NONE and
then redefine it. But the original definition is unused because NCR5380.c
lacks support for tagged queueing. So just define it once.

The TAG_NEXT macro only appears in the arguments to NCR5380_select() calls.
But that routine doesn't use its tag argument as the tag was already
assigned in NCR5380_main(). So remove the unused argument and the macro.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make use of the host template static initializer instead of assigning
handlers at run-time. Move __maybe_unused qualifiers from declarations
to definitions. Move the atari_scsi_bus_reset() wrapper after the
definition of NCR5380_bus_reset(). All of the host template handler
prototypes are now redundant so remove them.

The write_info() handler is only relevant to drivers using PSEUDO_DMA so
this patch fixes the compiler warning in atari_NCR5380.c and sun3_NCR5380.c:

  CC      drivers/scsi/atari_scsi.o
  drivers/scsi/NCR5380.h:329: warning: 'NCR5380_write_info' declared 'static' but never defined
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Having defined NDEBUG, and having set the console log level, I'd like to see
some output. Don't use pr_debug(), it's annoying to have to define DEBUG as
well.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Tested-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This is the delta between the two submissions:
[PATCH 00/12] scsi/NCR5380: fix debugging macros and #include structure
and
[PATCH v2 00/12] scsi/NCR5380: fix debugging macros and #include structure

The macro definition changes were discussed on the mailing list during
review. The idea is to get the compiler to check the parameters of
disabled printk() calls so that the debugging code doesn't rot again.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

All three NCR5380 core driver implementations share the same NCR5380.h
header file so they need to agree on certain macro definitions.

The flag bit used by the NDEBUG_MERGING macro in atari_NCR5380 and
sun3_NCR5380 collides with the bit used by NDEBUG_LISTS.

Moreover, NDEBUG_ABORT appears in NCR5380.c so it should be defined in
NCR5380.h rather than in each of the many drivers using that core.

An undefined NDEBUG_ABORT macro caused compiler errors and led to dodgy
workarounds in the core driver that can now be removed.
(See commits f566a576 and
185a7a1c.)

Move all of the NDEBUG_ABORT, NDEBUG_TAGS and NDEBUG_MERGING macro
definitions into NCR5380.h where all the other NDEBUG macros live.

Also, incorrect "#ifdef NDEBUG" becomes "#if NDEBUG" to fix the warning:
drivers/scsi/mac_scsi.c: At top level:
drivers/scsi/NCR5380.c:418: warning: 'NCR5380_print' defined but not used
drivers/scsi/NCR5380.c:459: warning: 'NCR5380_print_phase' defined but not used

The debugging code is now enabled when NDEBUG != 0.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NSam Creasey <sammy@sammy.net>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There are three implementations of the core NCR5380 driver and three sets
of debugging macro definitions. And all three implementations use the
NCR5380.h header as well.

Two of the definitions of the dprintk macro accept a variable argument list
whereas the third does not. Standardize on the variable argument list.
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NSam Creasey <sammy@sammy.net>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Acked-by: NSam Creasey <sammy@sammy.net>
Signed-off-by: NChristoph Hellwig <hch@lst.de>