It is not uncommon to boot a root filesystem from a USB
pendrive and similar, so enable USB mass storage, backed
by SCSI and SD block devices in the RealView defconfig.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We enabled SMP in the realview_defconfig so delete the
SMP-specific defconfig.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The realview has two defconfigs: realview_defconfig and
realview-smp_defconfig. We now have working SMP_ON_UP so
make them equal so we can delete the -smp variant. For
some reason NO_HZ_FULL was missing from the plain
realview_defconfig.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.

Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.

The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.

Cc: stable@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This platform recently moved to multi-platform, so missed the global
fixup by commit e3246542 ("ARM: use "depends on" for SoC configs
instead of "if" after prompt").  Fix it now.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This platform was recently added, so missed the global fixup by
commit e3246542 ("ARM: use "depends on" for SoC configs instead
of "if" after prompt").  Fix it now.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This newly added code missed the global fixup by commit 75305275
("ARM: use const and __initconst for smp_operations").  So fix it now.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NMarc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

This newly added code missed the global fixup by commit 75305275
("ARM: use const and __initconst for smp_operations").  So fix it now.

Also, add missing "static" qualifier.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Add the copy_file_range() syscall to ARM.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix CPSW EMAC pinmux
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix UART3 pinmux.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Setup USB2 to act in "HOST" mode by default.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix SB-SOM EEPROM I2C address
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Revert commit 7cd6ca77 ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit")  It was already done and it is
just a duplicate.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.

Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.

While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.

and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.

Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a01 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+

No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec5 ("net: phy: Use interrupts when available in NOLINK state")
disables polling.

Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a01 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

After 57a38eff (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.

The phy IRQ and associated pinmux node is also added.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed

Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Change instance id of DBGU to 45.
Signed-off-by: NMohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com>
Fixes: 7c661394 ("ARM: at91: dt: add device tree file for SAMA5D4 SoC")
Cc: stable@vger.kernel.org   # 3.18+
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

This is used by Renesas R-Car SoCs.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: Nzhxihu <zhxihu@marvell.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

OpenRD-Client requires the CS42L51 codec.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang.  Scanning also appears broken without this patch.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Fixes: 687c2767 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: NTony Lindgren <tony@atomide.com>

In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Here're a few gpio pin related fixes:
  - remove pinctrl-0 definition from pinctrl, since those pins are used
    in other places such as gpio-fan and regulators.
  - keep initial state of power led
  - fix for alarm pin of gpio-fan.

Fixes: dc57844a ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The GPIOs controlling the LEDs, listed below, are active high, not low:
  - gpio-leds: "lswvl:red:alarm" pin
  - gpio-leds: "lswvl:red:func" pin
  - gpio-leds: "lswvl:amber:info" pin
  - gpio-leds: "lswvl:blue:func" pin
  - gpio-leds: "lswvl:red:hdderr{0,1}" pin

Fixes: c43379e1 ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The GPIOs controlling the LEDs, listed below, are active high, not low:
  - gpio-leds: "lswxl:blue:power" pin
  - gpio-leds: "lswxl:red:func" pin
  - gpio-leds: "lswxl:red:hdderr{0,1}" pin

Fixes: e54e4b1b ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"

The pin/bank issue was found when discussing Debian Bug #810894
  [https://bugs.debian.org/810894#47]

Fixes: c43379e1 ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: NArnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"

Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
  - gpio-leds: "lswxl:blue:power" pin
  - gpio-leds: "lswxl:red:func" pin
  - gpio-leds: "lswxl:red:hdderr0" pin
  - gpio-leds: "lswxl:red:hdderr1" pin
  - gpio-fan:  low/high/alarm pin

The pin/bank issue was found when discussing Debian Bug #810894
  [https://bugs.debian.org/810894#47]

Fixes: e54e4b1b ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: NArnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

The Armada 38x based boards use this "PHY" with their xhci usb
controller. It would be also used for Armada 39x and Armada 375 base
boars which also had xhci controller.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

As of commit e488ca9f ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Do not disable branch prediction, as this has a big performance impact.

After re-enabling branch prediction, __loop_delay() runs 16 (Cortex A15)
or 11 (Cortex A9) times faster than before.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>