Supports Altera SOCFPGA bridges:
 * fpga2sdram
 * fpga2hps
 * hps2fpga
 * lwhps2fpga

Allows enabling/disabling the bridges through the FPGA
Bridge Framework API functions.

The fpga2sdram driver only supports enabling and disabling
of the ports that been configured early on.  This is due to
a hardware limitation where the read, write, and command
ports on the fpga2sdram bridge can only be reconfigured
while there are no transactions to the sdram, i.e. when
running out of OCRAM before the kernel boots.

Device tree property 'init-val' configures the driver to
enable or disable the bridge during probe.  If the property
does not exist, the driver will leave the bridge in its
current state.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Signed-off-by: NMatthew Gerlach <mgerlach@altera.com>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

FPGA Regions support programming FPGA under control of the Device
Tree.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This framework adds API functions for enabling/
disabling FPGA bridges under kernel control.

This allows the Linux kernel to disable FPGA bridges
during FPGA reprogramming and to enable FPGA bridges
when FPGA reprogramming is done.  This framework is
be manufacturer-agnostic, allowing it to be used in
interfaces that use the FPGA Manager Framework to
reprogram FPGA's.

The functions are:
* of_fpga_bridge_get
* fpga_bridge_put
   Get/put an exclusive reference to a FPGA bridge.

* fpga_bridge_enable
* fpga_bridge_disable
   Enable/Disable traffic through a bridge.

* fpga_bridge_register
* fpga_bridge_unregister
   Register/unregister a device-specific low level FPGA
   Bridge driver.

Get an exclusive reference to a bridge and add it to a list:
* fpga_bridge_get_to_list

To enable/disable/put a set of bridges that are on a list:
* fpga_bridges_enable
* fpga_bridges_disable
* fpga_bridges_put
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add documentation for new FPGA bridge class's sysfs interface.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a minor change in the FPGA Manager API
to hold information that is specific to an FPGA image
file.  This change is expected to bring little, if any,
pain.  The socfpga and zynq drivers are fixed up in
this patch.

An FPGA image file will have particulars that affect how the
image is programmed to the FPGA.  One example is that
current 'flags' currently has one bit which shows whether the
FPGA image was built for full reconfiguration or partial
reconfiguration.  Another example is timeout values for
enabling or disabling the bridges in the FPGA.  As the
complexity of the FPGA design increases, the bridges in the
FPGA may take longer times to enable or disable.

This patch adds a new 'struct fpga_image_info', moves the
current 'u32 flags' to it.  Two other image-specific u32's
are added for the bridge enable/disable timeouts.  The FPGA
Manager API functions are changed, replacing the 'u32 flag'
parameter with a pointer to struct fpga_image_info.
Subsequent patches fix the existing low level FPGA manager
drivers.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

New bindings document for FPGA Region to support programming
FPGA's under Device Tree control
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Signed-off-by: NMoritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a minor change in the FPGA Manager API
to hold information that is specific to an FPGA image
file.  This change is expected to bring little, if any,
pain.

An FPGA image file will have particulars that affect how the
image is programmed to the FPGA.  One example is that
current 'flags' currently has one bit which shows whether the
FPGA image was built for full reconfiguration or partial
reconfiguration.  Another example is timeout values for
enabling or disabling the bridges in the FPGA.  As the
complexity of the FPGA design increases, the bridges in the
FPGA may take longer times to enable or disable.

This patch documents the change in the FPGA Manager API
functions, replacing the 'u32 flag' parameter with a pointer
to struct fpga_image_info.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The intent is to provide a non-DT method of getting
ahold of a FPGA manager to do some FPGA programming.

This patch refactors of_fpga_mgr_get() to reuse most of it
while adding a new method fpga_mgr_get() for getting a
pointer to a fpga manager struct, given the device.
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch add of overlay notifications.

When DT overlays are being added, some drivers/subsystems
need to see device tree overlays before the changes go into
the live tree.

This is distinct from reconfig notifiers that are
post-apply or post-remove and which issue very granular
notifications without providing access to the context
of a whole overlay.

The following 4 notificatons are issued:
  OF_OVERLAY_PRE_APPLY
  OF_OVERLAY_POST_APPLY
  OF_OVERLAY_PRE_REMOVE
  OF_OVERLAY_POST_REMOVE

In the case of pre-apply notification, if the notifier
returns error, the overlay will be rejected.

This patch exports two functions for registering/unregistering
notifications:
  of_overlay_notifier_register(struct notifier_block *nb)
  of_overlay_notifier_unregister(struct notifier_block *nb)

The of_mutex is held during these notifications. The
notification data includes pointers to the overlay target
and the overlay:

struct of_overlay_notify_data {
       struct device_node *overlay;
       struct device_node *target;
};
Signed-off-by: NAlan Tull <atull@opensource.altera.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Makefile currently controlling compilation of this code is obj-y,
meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular usage, so that when reading
the driver there is no doubt it is builtin-only.

Since module_misc_device translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

config BF561_COREB
        bool "Enable Core B loader"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_misc_device translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Cc: Bas Vermeulen <bvermeul@blackstar.xs4all.nl>
Cc: Steven Miao <realmz6@gmail.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

drivers/lightnvm/Kconfig:menuconfig NVM
drivers/lightnvm/Kconfig:       bool "Open-Channel SSD target support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_misc_driver translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We replace module.h with moduleparam.h because this file still uses
module params to control behaviour.

Also note that MODULE_ALIAS is a no-op for non-modular code.

Cc: Matias Bjorling <mb@lightnvm.io>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NRobin van der Gracht <robin@protonic.nl>
CC: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Added a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by: NRobin van der Gracht <robin@protonic.nl>
CC: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Tell the FW that we are running a sane OS and TPM2_ChangeEPS()
is supported. This workaround was added to support other broken OS
and we need to follow here. The command is sent just once at the boot time.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The flush_icache_range() API is meant to be used on kernel addresses
only as it may not have the infrastructure (exception entries) to handle
user memory faults.

The lkdtm execute_user_location() function tests the kernel execution of
user space addresses by mmap'ing an anonymous page, copying some code
together with cache maintenance and attempting to run it. However, the
cache maintenance step may fail because of the incorrect API usage
described above. The patch changes lkdtm to use access_process_vm() for
copying the code into user space which would take care of the necessary
cache maintenance.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
[kees: export access_process_vm() for module use]
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Moving from get_user_pages() to get_user_pages_unlocked() simplifies the code
and takes advantage of VM_FAULT_RETRY functionality when faulting in pages.
Signed-off-by: NLorenzo Stoakes <lstoakes@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for 32 and 64-bit versions of Broadcom's On-Chip OTP
controller. These controllers are used on SoC's such as Cygnus and
Stingray.
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Tested-by: NJonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NOza Pawandeep <oza@broadcom.com>
Signed-off-by: NJonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Tested-by: NJonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: NScott Branden <scott.branden@broadcom.com>
Signed-off-by: NOza Pawandeep <oza@broadcom.com>
Signed-off-by: NJonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Documenation for the LPC18xx/43xx OTP memory bindings.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add simple read only driver for the internal OTP (One Time Programmable)
memory found on all NXP LPC18xx and LPC43xx devices.

The OTP memory is split into 4 banks each with 4 32-bits word. Some of
the banks contain predefined data while others are for general purpose
and user programmable via the OTP API in ROM. Note that writing to the
OTP memory is not yet supported.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Tested-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The code was already configured that way, but the Kconfig
file didn't support requesting it.

A buglet caused a null pointer deref when unloading the
module, but this commit also corrects that issue.
Signed-off-by: NChris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prepare the client write functions to set the internal flag in message
header. Carry both blocking and internal modes inside the transmit cb,
and call internal bus function  __mei_cl_send() with send mode bit mask.
The Internal flag should be added only on messages generated by the
driver.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This first patch updates the NHI Thunderbolt controller registers file to
reflect that it is not only for Cactus Ridge.
No functional change intended.
Signed-off-by: NAmir Levy <amir.jer.levy@intel.com>
Signed-off-by: NAndreas Noever <andreas.noever@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signal the host when we determine the host is to be signaled -
on th read path. The currrent code determines the need to signal in the
ringbuffer code and actually issues the signal elsewhere. This can result
in the host viewing this interrupt as spurious since the host may also
poll the channel. Make the necessary adjustments.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signal the host when we determine the host is to be signaled.
The currrent code determines the need to signal in the ringbuffer
code and actually issues the signal elsewhere. This can result
in the host viewing this interrupt as spurious since the host may also
poll the channel. Make the necessary adjustments.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

One of the factors that can result in the host concluding that a given
guest in mounting a DOS attack is if the guest generates interrupts
to the host when the host is not expecting it. If these "spurious"
interrupts reach a certain rate, the host can throttle the guest to
minimize the impact. The host computation of the "expected number
of interrupts" is strictly based on the ring transitions. Until
the host logic is fixed, base the guest logic to interrupt solely
on the ring state.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unnecessary header files and netlink related code as the daemons
do not use netlink to communicate with the kernel now.
Signed-off-by: NWeibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_kvp_daemon.c: In function .kvp_mac_to_if_name.:
hv_kvp_daemon.c:705:2: warning: format not a string literal and no format arguments [-Wformat-security]
  snprintf(dev_id, sizeof(dev_id), kvp_net_dir);
  ^
hv_kvp_daemon.c:705:2: warning: format not a string literal and no format arguments [-Wformat-security]
Signed-off-by: NWeibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The link flag pthread is not needed.
Signed-off-by: NWeibing Zhang <atheism.zhang@gmail.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Balloon driver was only printing the size of the info blob and not the
actual content. This fixes it so that the info blob (max page count as
configured in Hyper-V) is printed out.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Increase the timeout of backup operations. When system is under I/O load,
it needs more time to freeze. These timeout values should also match the
host timeout values more closely.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding log messages to help troubleshoot error cases and transaction
handling.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Added logging to help troubleshoot common ballooning, hot add,
and versioning issues.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the guest does not support memory hotplugging, it should respond to
the host with zero pages added and successful result code. This signals
to the host that hotplugging is not supported and the host will avoid
sending future hot-add requests.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We should intentionally declare the protocols to use for every known host
and default to using the latest protocol if the host is unknown or new.
Signed-off-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

I discovered that at least WS2016TP5 host has 60 seconds timeout for the
ICMSGTYPE_NEGOTIATE message so we need to lower guest's timeout a little
bit to make sure we always respond in time. Let's make it 55 seconds.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With wrap around mappings in place we can always provide drivers with
direct links to packets on the ring buffer, even when they wrap around.
Do the required updates to get_next_pkt_raw()/put_pkt_raw()

The first version of this commit was reverted (65a532f3) to deal with
cross-tree merge issues which are (hopefully) resolved now.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Tested-by: NDexuan Cui <decui@microsoft.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch introduces a vendor prefix for Holtek Semiconductor Inc.
Signed-off-by: NRobin van der Gracht <robin@protonic.nl>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A mei client driver on the mei client bus can call disconnect function on
already internal disconnected client.  A client can disconnect internally,
for example, during link reset or upon FW request. Those are legitimate
flows and we should not log an error message, hence we demote
'Already disconnected' message to the debug level.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>