It is possible to get a lockup if kernel decides to enter LP2 cpuidle
from some clk-notifier, in that case CCF's "prepare" mutex is kept locked
and thus clk_get_rate(pclk) blocks on the same mutex with interrupts being
disabled, hanging machine.
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add regulators coupler for Tegra30 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.

There are 2 coupled regulators on all Tegra30 SoCs: CORE and CPU. The
coupled regulator voltages shall be in a range of 300mV from each other
and CORE voltage shall be higher than the CPU by N mV, where N depends
on the CPU voltage.
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add regulators coupler for Tegra20 SoCs that performs voltage balancing
of a coupled regulators and thus provides voltage scaling functionality.

There are 3 coupled regulators on all Tegra20 SoCs: CORE, RTC and CPU.
The CORE and RTC voltages shall be in range of 170mV from each other and
they both shall be higher than the CPU voltage by at least 120mV. This
sounds like it could be handle by a generic voltage balancer, but the CORE
voltage scaling isn't implemented in any of the upstream drivers yet.
It will take quite some time and effort to hook up voltage scaling for
all of the drivers, hence we will use a custom coupler that will manage
the CPU voltage scaling for the starter.
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Acked-By: NPeter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Tegra210 and prior Tegra chips have deep sleep entry and wakeup related
timings which are platform specific that should be configured before
entering into deep sleep.

Below are the timing specific configurations for deep sleep entry and
wakeup.
- Core rail power-on stabilization timer
- OSC clock stabilization timer after SOC rail power is stabilized.
- Core power off time is the minimum wake delay to keep the system
  in deep sleep state irrespective of any quick wake event.

These values depends on the discharge time of regulators and turn OFF
time of the PMIC to allow the complete system to finish entering into
deep sleep state.

These values vary based on the platform design and are specified
through the device tree.

This patch has implementation to configure these timings which are must
to have for proper deep sleep and wakeup operations.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch configures polarity of the core power request signal
in PMC control register based on the device tree property.

PMC asserts and de-asserts power request signal based on it polarity
when it need to power-up and power-down the core rail during SC7.
Reviewed-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch implements PMC wakeup sequence for Tegra210 and defines the
commonly used RTC alarm wake event.
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch allows to create separate irq_set_wake and irq_set_type
implementations for different Tegra designs PMC that has different
wake models which require difference wake registers and different
programming sequence.

AOWAKE model support is available for Tegra186 and Tegra194 only
and it resides within PMC and supports tiered wake architecture.

Tegra210 and prior Tegra designs uses PMC directly to receive wake
events and coordinate the wake sequence.
Reviewed-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NSowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Typically nvmem cells would be stored in device tree. However, for
compatibility with device trees that don't contain nvmem cell
definitions, register lookups for cells currently used by consumers.
This allows the consumers to use the same API to query cells from the
device tree or using the legacy mechanism.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Create nvmem cells for all the fuses currently used by consumers.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The nvmem framework provides a generic infrastructure and API to access
the type of information stored in fuses such as the Tegra FUSE block.

Implement an nvmem device that can be used to access the information in
a more generic way to decouple consumers from the custom Tegra API and
to add a more formal way of creating the dependency between the FUSE
device and the consumers.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Make sure to also restore the register base address on sysfs
registration failure.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Interrupts that don't have an associated wake event or GPIO wake events
end up with an associate IRQ chip that is NULL and which causes IRQ code
to crash. This is because we don't implicitly set the parent IRQ chip by
allocating the interrupt at the parent. However, there really isn't a
corresponding interrupt at the parent, so we need to work around this by
setting the special no_irq_chip as the IRQ chip for these interrupts.

Fixes: 19906e6b ("soc/tegra: pmc: Add wake event support")
Signed-off-by: NThierry Reding <treding@nvidia.com>

tegra_fuse_readl() can be called from drivers at any time. If this API
is called before tegra_fuse_probe(), we end up enabling the clock before
it is registered. Add a check for the FUSE clock in tegra_fuse_readl()
and propagate any errors.
Signed-off-by: NNagarjuna Kristam <nkristam@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

tegra_powergate_sequence_power_up() powers up partition and also enables
clock & reset. However, if a controller like PCIe have multiple clocks
& resets and they need to be enabled in a sequence, driver must use
standalone function tegra_powergate_power_on() to power up partition.

Export tegra_powergate_power_on() to allow Tegra controller drivers to
unpower gate partition independent to clock & reset.
Signed-off-by: NManikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NThierry Reding <treding@nvidia.com>

Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NEnrico Weigelt <info@metux.net>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Select PINCTRL_TEGRA194 by default for Tegra194 SoC needed for
dynamically controlling PCIe pins.
Signed-off-by: NKrishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms and conditions of the gnu general public license
  version 2 as published by the free software foundation this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.745679586@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms and conditions of the gnu general public license
  version 2 as published by the free software foundation this program
  is distributed in the hope it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NAlexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 1 normalized pattern(s):

  this software is licensed under the terms of the gnu general public
  license version 2 as published by the free software foundation and
  may be copied distributed and modified under those terms this
  program is distributed in the hope that it will be useful but
  without any warranty without even the implied warranty of
  merchantability or fitness for a particular purpose see the gnu
  general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAlexios Zavras <alexios.zavras@intel.com>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Recent changes have made it much more probable that clocks are not
available yet when the FUSE driver is first probed. However, that is a
situation that the driver can cope with just fine.

To avoid confusion, don't output an error when this happens.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Add some comments to clarify the purpose of the wake event support
implemented in the PMC driver.
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

For interrupts that are not wakeup sources but that may end up getting
mapped through the PMC as interrupt parent (this can happen for GPIOs),
return early in order to avoid a subsequent crash from an out-of-bounds
access to the register region.
Reported-by: NBitan Biswas <bbiswas@nvidia.com>
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The code currently doesn't support allocating more than one wake IRQ at
a time. Detect this situation and error out. Also make sure to output a
warning when that happens to help track down callers.
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms and conditions of the gnu general public license
  version 2 as published by the free software foundation this program
  is distributed in the hope it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NSteve Winslow <swinslow@gmail.com>
Reviewed-by: NRichard Fontana <rfontana@redhat.com>
Reviewed-by: NAlexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The __dma_request_channel() prototype has been changed to help to do
device node validation, thus we can use dma_request_channel() instead
of __dma_request_channel() to keep kernel bisectable.
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NVinod Koul <vkoul@kernel.org>

Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 8df12745 ("soc/tegra: pmc: Enable XUSB partitions on boot")
was added as a workaround to ensure that the XUSB powergates or domains
were turned on early during boot because as this time the Tegra XHCI
driver did not handle the power domains at all. Now that the Tegra XHCI
driver has been updated to properly managed the power domains, the
workaround to enable the XUSB power domain early has been removed. This
also means that we can now move the initialisation of the powergates
into the PMC driver probe. Therefore, move the powergate initialisation
into the PMC driver probe and return any errors detected. To handle any
errors, functions to cleanup and remove any power-domains registered
with the generic power-domain framework have been added.

Finally the initialisation of the 'powergates_available' bitmask is kept
in the PMC early init function to allow the legacy PMC powergate APIs to
be called during early boot for enabling secondary CPUs on 32-bit Tegra
devices.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Commit 5f84bb1a ("soc/tegra: pmc: Add sysfs entries for reset info")
added sysfs entries for Tegra reset source and level. However, these
sysfs are not removed on error and so if the registering of PMC device
is probe deferred, then the next time we attempt to probe the PMC device
warnings such as the following will be displayed on boot ...

  sysfs: cannot create duplicate filename '/devices/platform/7000e400.pmc/reset_reason'

Fix this by calling device_remove_file() for each sysfs entry added on
failure. Note that we call device_remove_file() unconditionally without
checking if the sysfs entry was created in the first place, but this
should be OK because kernfs_remove_by_name_ns() will fail silently.

Fixes: 5f84bb1a ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Commit 5f84bb1a ("soc/tegra: pmc: Add sysfs entries for reset info")
added support for reading the Tegra reset source and level from sysfs.
However, there are a few issues with this commit which are ...
1. The number of reset sources for Tegra210 is defined as 5 but it
   should be 6.
2. The number of reset sources for Tegra186 is defined as 13 but it
   should be 15.
3. The SoC data variables num_reset_sources and num_reset_levels are
   defined but never used.

Fix the above by ...

1. Removing the reset source 'AOTAG' from the tegra30_reset_sources
   because this is only applicable for Tegra210.
2. Adding a new tegra210_reset_sources structure for Tegra210 reset
   sources.
3. Correct the number of reset sources for Tegra210 and Tegra186 by
   using the ARRAY_SIZE macro.
4. Updating the functions reset_reason_show() and reset_level_show()
   to check whether the value read is valid. While we are at it
   clean-up these functions to remove an unnecessary u32 variable.

Fixes: 5f84bb1a ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

By implementing the acquire/release protocol, the resets can be shared
with other drivers that also adhere to this protocol. This will be used
for example by the SOR driver to put hardware into a known good state,
irrespective of whether or not the power domain can be reset.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The tegra timer is necessary for Tegra210 to support CPU idle power-down
state. So select it by default.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Acked-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

On Tegra210 systems with new enough boot software, direct register
accesses to PMC register space from the non-secure world are not
allowed. Instead a monitor call may be used to read and write PMC
registers.

Add code to detect such a system by attempting to write a scratch
register and detecting if the write happened or not. If not, we switch
to doing all register accesses through the monitor call.
Signed-off-by: NMikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

It's not strictly necessary to initialize the fields in struct
tegra_pmc_soc if they are 0/false. However, we already initialize them
explicitly even if unnecessary, so keep doing that for consistency.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

Some recently added code used weird alignment and indentation. Fix these
occurrences to make them consistent with the rest of the code.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

Instead of using the global pmc variable, pass around a pointer where
possible. Also, replace most occurrences of pr_*() functions by their
equivalent dev_*() functions, reusing the pmc->dev pointer.

It's not possible to get completely rid of the global variable because
some of the public API that this driver exposes still relies on it.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

Now there are no more external users of tegra_powergate_is_powered(),
make this a local function.
Signed-off-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

Some of the fields in struct tegra_pmc had not been documented when they
were added. Add the missing kerneldoc.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

This will make it easier to insert new includes in the right place in
subsequent patches.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>

The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Fix typo when reading SoC speedo value from fuse SoC speedo register.
Reported-by: NMark Zhang <markz@nvidia.com>
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>