Those functions are only used on vlv platforms, so no need to check.
Especially if we're not too consistent about it.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With all the preceding refactoring the dp mode_set callback only
computes a bit of state (all derived from the pipe config) and also
writes the eld. As long as we do that before we enable the audio bit
or depend upon the correct value in intel_dp->DP we'll be fine.

No other hw state is touched.

We therefore only need to check that clearing intel_dp->DP is save.
Which it is since when we re-enable we already mask out all the bits
the link training code sets. And we need to keep on doing that so that
the re-train loop walking over pre-emph/voltage-swing values still
works properly.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Only ilk/snb/ivb need the port A pll setup, so move it to the
pre_enable hook for those platforms. We can savely do this since on
those platforms there's nothing that touches the hardware between the
encoder->mode_set and the encoder->pre_enable calls.

Also add a comment that port A is ilk+ only.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.

Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
  that means some pretty extensive reworking of our code which
  currently does all this while the pipe/port is still off.

I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
  encoder.

I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There's no need to check whether audio is enabled (which for ddi ports
is done through the crtc->eld_vld flag) since at the cost of a
potentially unecessary register rmw cycle we can unconditionally do
this.

Note that the edp check is just paranoia since we won't ever call the
write_eld function for an edp panel.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way we can rely on the state cross-checker to have a bit
assurance that we'll get it right.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

At least on those platforms which have a simple bit and don't rely
on the fully programmable CSC unit to do this.

Note that with the current code this includes CHV, but I guess that
platform will match BYT.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We in the pre_enable hook we should only rely on the pipe config and
not on some other state set through properties or detect functions.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For compliance we really should be sending NULL infoframes always
when we detect a hdmi capable monitor. Also remove the now redudant
setting for the has_audio case and enforce that audio is only
possible with a hdmi sink.
Reviewed-by: NNaresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everything should be in place so enable rc6/rps for bdw.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

by correctly displaying result and requested.
Suggested-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In BDW, Apart from unmasking up/down threshold interrupts. we need
to umask bit 32 of PM_INTRMASK to route interrupts to target via Display
Interface.

v2: Add (1<<31) mask (Ville)

v3: Add Gen check for the mask (ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Almost all of it is reusable from the existing code. The primary
difference is we need to do even less in the interrupt handler, since
interrupts are not shared in the same way.

The patch is mostly a copy-paste of the existing snb+ code, with updates
to the relevant parts requiring changes to the interrupt handling. As
such it /should/ be relatively trivial. It's highly likely that I missed
some places where I need a gen8 version of the PM interrupts, but it has
become invisible to me by now.

This patch could probably be split into adding the new functions,
followed by actually handling the interrupts. Since the code is
currently disabled (and broken) I think the patch stands better by
itself.

v2: Move the commit about not touching the ringbuffer interrupt to the
snb_* function where it belongs (Rodrigo)

v3: Rebased on Paulo's runtime PM changes

v4: Not well validated, but rebase on
commit 730488b2
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Mar 7 20:12:32 2014 -0300

    drm/i915: kill dev_priv->pm.regsave

v5: Rebased on latest code base. (Deepak)

v6: Remove conflict markers, Unnecessary empty line and use right
IIR interrupt (Ville)

v7: mask modified without rmw (Ville Syrjälä)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDeepak S <deepak.s@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we dont have semaphores enabled, we allocate 4
dwords for signalling. But end up emitting more regardless.

Fix this by bailing out early if semaphores are not enabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78274
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78283Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added as generic parameters which will be initialized in the panel
driver and are specific to panels.

Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These are generated with intel-gpu-tools/tools/null_state_gen

v2: Don't use header file for states (Daniel Vetter)

v3: Proper URB state size for gen8/GT3 (Damien Lespiau)

Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: Oscar Mateo <oscar.mateo@intel.com> (v2)
Acked-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

HW guys say that it is not a cool idea to let device
go into rc6 without proper 3d pipeline state.

For each new uninitialized context, generate a
valid null render state to be run on context
creation.

This patch introduces a skeleton with empty states.

v2: - No need to vmap (Chris Wilson)
    - use .c files for state (Daniel Vetter)
    - no need to flush as i915_add_request does it
    - remove parameter for batch alloc size
    - don't wait for the init (Ben Widawsky)

v3: - move to cpu/gpu (Chris Wilson)

Tested-by: Kristen Carlson Accardi <kristen@linux.intel.com> (v1)
Tested-by: NOscar Mateo <oscar.mateo@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise we end up tearing down fences when e.g. the client quits
way too early. Might or might not fix a fence pin_count BUG Ville has
reported.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Userspace can currently provoke this when e.g. trying to use a pinned
scanout as a cursor or overlay target. Later on that might lead to
some fun fence pin count mayhem.

Spurred by Ville's report that something goes wrong here and
originally I've thought that this might slip through the pwrite gtt
fastpath. But that one checks of obj tiling, so should be ok.

But one thing that _does_ blow up is the vma unbinding with more than
one address space. The next patch will fix this.

v2: Use a WARN_ON - Chris pointed out that we already catch all cases
so userspace can't provoke this like I've originally feared.

While reviewing relevant code I've noticed a pile of DRM_ERROR in the
overlay&cursor code which are all triggerable by userspace. Tune them
down while at it.

v3: Split out the DRM_ERROR->DRM_DEBUG_KMS change into a separate patch,
as requested by Chris.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Noticed while playing with coccinelle.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

During initial probing of the modes to assign to the fbdev console, we
use the CRTC and connector ids. These are much harder for us to
understand than if we used their actual names (or pipe in the CRTC
case). Similarly, we want to manually print the mode size rather than
rely on mode->name being set.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Patch done using the following semantic patch (thanks Daniel for the
help!)

  @@
  iterator name list_for_each_entry;
  iterator name for_each_crtc;
  struct drm_crtc * crtc;
  struct drm_device * dev;
  @@
  -list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
  +for_each_crtc(dev,crtc) {
  	...
  }

Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Generated using the semantic patch:

  @@
  iterator name list_for_each_entry;
  iterator name for_each_intel_crtc;
  struct intel_crtc * crtc;
  struct drm_device * dev;
  @@
  -list_for_each_entry(crtc,&dev->mode_config.crtc_list,...) {
  +for_each_intel_crtc(dev,crtc) {
	...
  }

Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fed up with having that long list_for_each_entry() invocation?

Use for_each_intel_crtc()!
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Squash in patch that exported ilk_wm_max_level.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That's not necessary and makes the code not as neat as it could be.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Somehow UXA submits a completely bogus DR4 value since essentially
forever. It was originally introduced in

commit bade7d7d2505a10a8a7d24b084aff9742e2d6d64
Author: Eric Anholt <eric@anholt.net>
Date:   Fri Jun 6 14:03:25 2008 -0700

    Use the DRM for submitting batchbuffers when available.

and dutifully copied around ever since. Since we want to keep the
general dirt catching around just special case the UXA value.

This regression was introduced in

commit 9cb34664
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Apr 24 08:09:11 2014 +0200

    drm/i915: Catch dirt in unused execbuffer fields

Comment from Chris' review:

"To be fair, it is a sensible value if one supposes a Region style API to
cliprects. Under that API, DR[14] define the extents of the clip region,
and ((0,0), (0,0)) [DR1==DR4==0] would mean all clipped, do not draw
anything."

v2: Pimp commit message a bit and remove the double space.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78494
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jörg Otte <jrg.otte@gmail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The fence pin count should always be <= the bo pin count. If that's
not the case then we have a funny problem and are leaking references
somewhere.

Which means we can catch fence pin leaks by checking for the same
upper limit as we do for the bo pin count. Inspired by a discussion
with Ville about a fence leak igt testcase.

v2: Also check for fence->pin_count <= ggtt_vma->pin_count, since that
might catch a leak even quicker. Also de-inline them, they're getting
too big.

v3: Don't separately check for MAX_PIN_COUNT since the > vma->pin_count
check will catch that already (Chris).

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The pipe might not start to actually run until the port has been enabled
(depends on the platform and port type). So don't try to wait for vblank
after we enabled the pipe but haven't yet enabled the port.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=77297Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already moved the plane disable/enable to happen as the first/last
thing on every other platforms. Follow suit with gmch platforms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Frob drm_vblank_on conflict, as usual.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is missing in:

commit 78325f2d
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date:   Tue Apr 29 14:52:29 2014 -0700

    drm/i915: Virtualize the ringbuffer signal func

Looks to me like a rebase side-effect...
Signed-off-by: NOscar Mateo <oscar.mateo@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

gen8_stolen_size() is missing __init, so add it.

Also all the intel_stolen_funcs structures can be marked
__initconst.

intel_stolen_ids[] can also be made const if we replace the
__initdata with __initconst.

Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV uses the same bits as SNB/VLV to code the Graphics Mode Select field
(GFX stolen memory size) with the addition of finer granularity modes:
4MB increments from 0x11 (8MB) to 0x1d.

Values strictly above 0x1d are either reserved or not supported.

v2: 4MB increments, not 8MB. 32MB has been omitted from the list of new
    values (Ville Syrjälä)

v3: Also correctly interpret GGMS (GTT Graphics Memory Size) (Ville
    Syrjälä)

v4: Don't assign a value that needs 20bits or more to a u16 (Rafael
    Barbalho)

[vsyrjala: v5: Split from i915 changes and add chv_stolen_funcs]

Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRafael Barbalho <rafael.barbalho@intel.com>
Tested-by: NRafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV uses the same bits as SNB/VLV to code the Graphics Mode Select field
(GFX stolen memory size) with the addition of finer granularity modes:
4MB increments from 0x11 (8MB) to 0x1d.

Values strictly above 0x1d are either reserved or not supported.

v2: 4MB increments, not 8MB. 32MB has been omitted from the list of new
    values (Ville Syrjälä)

v3: Also correctly interpret GGMS (GTT Graphics Memory Size) (Ville
    Syrjälä)

v4: Don't assign a value that needs 20bits or more to a u16 (Rafael
    Barbalho)

[vsyrjala: v5: Split the early quirks to another patch]
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRafael Barbalho <rafael.barbalho@intel.com>
Tested-by: NRafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No CRT output on CHV, so don't call intel_crt_init().

v2: Don't disable CRT on HAS.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add chv_crtc_clock_get() to read out the DPLL settings.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
[danvet: Fix compile due to bikeshedded headers in an earlier patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>