Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Improve handling of bpc (bits per color) in radeon.
In most cases we want 8 except for HDMI, DP, LVDS, and eDP.

v2: handle DP better.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Tested-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some r4xx chips have the wrong frev in the
DVOEncoderControl table.  It should always be 1
on r4xx.  Fixes modesetting on DVO on r4xx chips
with the bad frev.

Reported by twied on #radeon.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Using the bpc (bits per color) specified by the monitor
can cause problems in some cases.  Until we get a better
handle on how to deal with those cases, just use a bpc of 8.
Reported-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

TN (trinity) uses DP bridges for LVDS and VGA just like llano.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

HDMI 1.3 defines single link clocks up to 340 Mhz.
Refine the current dual link checks to only enable
dual link for DVI > 165 Mhz or HDMI > 340 Mhz if the
hw supports HDMI 1.3 (DCE3+).

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=44755Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We were previously just checking for audio.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

dig transmitter control table only has ENABLE/DISABLE actions
on DCE4.1/DCE5.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=44955Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Needs to happen earlier in the mode set.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use the table version to determine which params to use.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

set up the params based on the table version number.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Use table version numbers for param setup.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Leave the common code in radeon_encoders.c and move the atom
specific code to atombios_encoders.c.  This matches legacy
encoder setup and crtc setup.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DP MST is DP multi-stream support, part of DP 1.2.

v2: switch to a helper macro as suggested by Michel.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The existing function was getting too big and complex.
Break it down into a more manageable set of functions.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Return the encoder id rather than a boolean.  This is needed
for differentiate between multiple DP bridge chips.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Settings in this table reflect the physical panel/connector rather
than the internal dig encoding.

v2: fix typo for DRM_MODE_CONNECTOR_VGA case.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

llano has fully routeable dig encoders similar to DCE3.2 while
ontario has a hardcoded mapping similar to DCE4.0.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The encoders are supposedly fully routeable, but changing the mapping
doesn't always seem to take.  Using a hardcoded mapping is much more
reliable.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41366Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

DVOOutputControl checks the value of of bios scratch reg 3
on some tables and assumes the encoder is already enabled
if the DFP2_ACTIVE bit is set.  Clear that bit so the table
sets the DDIA enable bit properly.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to add support for 4 crtcs when setting the possible crtcs
for the encoders.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is used during phy init to set up the phy for DP.  This may
fix DP problems on DCE3.2 cards.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Certain revisions of the vbios on DCE3.2 cards have a bug
in the transmitter control table which prevents duallink from
being enabled properly on some cards.  The action switch statement
jumps to the wrong offset for the OUTPUT_ENABLE action.  The fix
is to use the ENABLE action rather than the OUTPUT_ENABLE action
on the affected cards.  In fixed version of the vbios, both
actions jump to the same offset, so the change should be safe.
Reported-and-tested-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

DP clock and lanes were not set properly for DP bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Required for DPMS on some systems.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to set up the bridge for DDC prior to the
i2c over aux transaction.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

dp to vga bridges for example.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This should give us more reliable results if the table
is called before an active device is set.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The PHY was not initialized correctly after
ac89af1e since
the function bailed early as an encoder was not
assigned.  The encoder isn't necessary for PHY init
so just assign to 0 for init so that the table
is executed.
Reported-by: NAri Savolainen <ari.m.savolainen@gmail.com>
Tested-by: NAri Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It only needs to be called once at startup, not for every
modeset.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- reorganize the functions based on use
- clean up function naming
- rework link training to better match what we use internally
- add initial support for DP 1.2 (no MST yet)
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Required for proper operation with DP bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders.  Internally we treat them mostly
like DP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Used for dp1.2 support and for dp bridges.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

need to wait for the panel to power up.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

eDP is usually used as an LVDS replacement, so treat
it more like LVDS from the user perspective.

v2: encoder mode is always DP for eDP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>