Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 08 3月, 2022 1 次提交
  3. 09 2月, 2022 1 次提交
    • V
      net: dsa: mt7530: fix kernel bug in mdiobus_free() when unbinding · 9ffe3d09
      由 Vladimir Oltean 提交于 
      Nobody in this driver calls mdiobus_unregister(), which is necessary if
mdiobus_register() completes successfully. So if the devres callbacks
that free the mdiobus get invoked (this is the case when unbinding the
driver), mdiobus_free() will BUG if the mdiobus is still registered,
which it is.

My speculation is that this is due to the fact that prior to commit
ac3a68d5 ("net: phy: don't abuse devres in devm_mdiobus_register()")
from June 2020, _devm_mdiobus_free() used to call mdiobus_unregister().
But at the time that the mt7530 support was introduced in May 2021, the
API was already changed. It's therefore likely that the blamed patch was
developed on an older tree, and incorrectly adapted to net-next. This
makes the Fixes: tag correct.

Fix the problem by using the devres variant of mdiobus_register.

Fixes: ba751e28 ("net: dsa: mt7530: add interrupt support")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      9ffe3d09
  5. 09 12月, 2021 4 次提交
    • V
      net: dsa: add a "tx_fwd_offload" argument to ->port_bridge_join · b079922b
      由 Vladimir Oltean 提交于 
      This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.

This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      b079922b
    • V
      net: dsa: keep the bridge_dev and bridge_num as part of the same structure · d3eed0e5
      由 Vladimir Oltean 提交于 
      The main desire behind this is to provide coherent bridge information to
the fast path without locking.

For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.

Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.

We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.

During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.

When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.

Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAlvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      d3eed0e5
    • V
      net: dsa: hide dp->bridge_dev and dp->bridge_num in drivers behind helpers · 41fb0cf1
      由 Vladimir Oltean 提交于 
      The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.

Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      41fb0cf1
    • V
      net: dsa: mt7530: iterate using dsa_switch_for_each_user_port in bridging ops · 872bb81d
      由 Vladimir Oltean 提交于 
      Avoid repeated calls to dsa_to_port() (some hidden behind dsa_is_user_port
and some in plain sight) by keeping two struct dsa_port references: one
to the port passed as argument, and another to the other ports of the
switch that we're iterating over.

dsa_to_port(ds, i) gets replaced by other_dp, i gets replaced by
other_port which is derived from other_dp->index, dsa_is_user_port is
handled by the DSA iterator.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      872bb81d
  7. 18 10月, 2021 1 次提交
  9. 19 9月, 2021 1 次提交
    • V
      net: dsa: be compatible with masters which unregister on shutdown · 0650bf52
      由 Vladimir Oltean 提交于 
      Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.

What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.

This message can be seen in a loop, and it hangs the reboot process there:

unregister_netdevice: waiting for eth0 to become free. Usage count = 3

So why 3?

A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:

dsa_slave_create
-> netdev_upper_dev_link
   -> __netdev_upper_dev_link
      -> __netdev_adjacent_dev_insert
         -> dev_hold

So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.

Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.

It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.

So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.

However, complications arise really quickly.

The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).

Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.

So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.

So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.

The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.

The answer to that question lies in this comment above device_link_add:

 * A side effect of the link creation is re-ordering of dpm_list and the
 * devices_kset list by moving the consumer device and all devices depending
 * on it to the ends of these lists (that does not happen to devices that have
 * not been registered when this function is called).

so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.

Fixes: 2f1e8ea7 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/Reported-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0650bf52
  11. 25 8月, 2021 1 次提交
  13. 12 8月, 2021 1 次提交
  15. 06 8月, 2021 3 次提交
  17. 04 8月, 2021 4 次提交
    • D
      net: dsa: mt7530: always install FDB entries with IVL and FID 1 · 73c447ca
      由 DENG Qingfang 提交于 
      This reverts commit 7e777021 ("mt7530 mt7530_fdb_write only set ivl
bit vid larger than 1").

Before this series, the default value of all ports' PVID is 1, which is
copied into the FDB entry, even if the ports are VLAN unaware. So
`bridge fdb show` will show entries like `dev swp0 vlan 1 self` even on
a VLAN-unaware bridge.

The blamed commit does not solve that issue completely, instead it may
cause a new issue that FDB is inaccessible in a VLAN-aware bridge with
PVID 1.

This series sets PVID to 0 on VLAN-unaware ports, so `bridge fdb show`
will no longer print `vlan 1` on VLAN-unaware bridges, and that special
case in fdb_write is not required anymore.

Set FDB entries' filter ID to 1 to match the VLAN table.
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      73c447ca
    • D
      net: dsa: mt7530: set STP state on filter ID 1 · a9e3f62d
      由 DENG Qingfang 提交于 
      As filter ID 1 is the only one used for bridges, set STP state on it.
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a9e3f62d
    • D
      net: dsa: mt7530: use independent VLAN learning on VLAN-unaware bridges · 6087175b
      由 DENG Qingfang 提交于 
      Consider the following bridge configuration, where bond0 is not
offloaded:

         +-- br0 --+
        / /   |     \
       / /    |      \
      /  |    |     bond0
     /   |    |     /   \
   swp0 swp1 swp2 swp3 swp4
     .        .       .
     .        .       .
     A        B       C

Ideally, when the switch receives a packet from swp3 or swp4, it should
forward the packet to the CPU, according to the port matrix and unknown
unicast flood settings.

But packet loss will happen if the destination address is at one of the
offloaded ports (swp0~2). For example, when client C sends a packet to
A, the FDB lookup will indicate that it should be forwarded to swp0, but
the port matrix of swp3 and swp4 is configured to only allow the CPU to
be its destination, so it is dropped.

However, this issue does not happen if the bridge is VLAN-aware. That is
because VLAN-aware bridges use independent VLAN learning, i.e. use VID
for FDB lookup, on offloaded ports. As swp3 and swp4 are not offloaded,
shared VLAN learning with default filter ID of 0 is used instead. So the
lookup for A with filter ID 0 never hits and the packet can be forwarded
to the CPU.

In the current code, only two combinations were used to toggle user
ports' VLAN awareness: one is PCR.PORT_VLAN set to port matrix mode with
PVC.VLAN_ATTR set to transparent port, the other is PCR.PORT_VLAN set to
security mode with PVC.VLAN_ATTR set to user port.

It turns out that only PVC.VLAN_ATTR contributes to VLAN awareness, and
port matrix mode just skips the VLAN table lookup. The reference manual
is somehow misleading when describing PORT_VLAN modes. It states that
PORT_MEM (VLAN port member) is used for destination if the VLAN table
lookup hits, but actually **PORT_MEM & PORT_MATRIX** (bitwise AND of
VLAN port member and port matrix) is used instead, which means we can
have two or more separate VLAN-aware bridges with the same PVID and
traffic won't leak between them.

Therefore, to solve this, enable independent VLAN learning with PVID 0
on VLAN-unaware bridges, by setting their PCR.PORT_VLAN to fallback
mode, while leaving standalone ports in port matrix mode. The CPU port
is always set to fallback mode to serve those bridges.

During testing, it is found that FDB lookup with filter ID of 0 will
also hit entries with VID 0 even with independent VLAN learning. To
avoid that, install all VLANs with filter ID of 1.
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6087175b
    • D
      net: dsa: mt7530: enable assisted learning on CPU port · 0b69c54c
      由 DENG Qingfang 提交于 
      Consider the following bridge configuration, where bond0 is not
offloaded:

         +-- br0 --+
        / /   |     \
       / /    |      \
      /  |    |     bond0
     /   |    |     /   \
   swp0 swp1 swp2 swp3 swp4
     .        .       .
     .        .       .
     A        B       C

Address learning is enabled on offloaded ports (swp0~2) and the CPU
port, so when client A sends a packet to C, the following will happen:

1. The switch learns that client A can be reached at swp0.
2. The switch probably already knows that client C can be reached at the
   CPU port, so it forwards the packet to the CPU.
3. The bridge core knows client C can be reached at bond0, so it
   forwards the packet back to the switch.
4. The switch learns that client A can be reached at the CPU port.
5. The switch forwards the packet to either swp3 or swp4, according to
   the packet's tag.

That makes client A's MAC address flap between swp0 and the CPU port. If
client B sends a packet to A, it is possible that the packet is
forwarded to the CPU. With offload_fwd_mark = 1, the bridge core won't
forward it back to the switch, resulting in packet loss.

As we have the assisted_learning_on_cpu_port in DSA core now, enable
that and disable hardware learning on the CPU port.
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NVladimir Oltean <oltean@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0b69c54c
  19. 02 8月, 2021 1 次提交
  21. 20 7月, 2021 1 次提交
  23. 17 7月, 2021 1 次提交
  25. 24 5月, 2021 1 次提交
    • D
      net: dsa: mt7530: fix VLAN traffic leaks · 474a2dda
      由 DENG Qingfang 提交于 
      PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but
was not reset when it is disabled, which may cause traffic leaks:

	ip link add br0 type bridge vlan_filtering 1
	ip link add br1 type bridge vlan_filtering 1
	ip link set swp0 master br0
	ip link set swp1 master br1
	ip link set br0 type bridge vlan_filtering 0
	ip link set br1 type bridge vlan_filtering 0
	# traffic in br0 and br1 will start leaking to each other

As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the
PCR_MATRIX write from mt7530_port_set_vlan_aware.

Fixes: 83163f7d ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: NDENG Qingfang <dqfext@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      474a2dda
  27. 20 5月, 2021 1 次提交
  29. 14 4月, 2021 1 次提交
  31. 29 3月, 2021 1 次提交
    • I
      net: dsa: mt7530: clean up core and TRGMII clock setup · 4732315c
      由 Ilya Lipnitskiy 提交于 
      Three minor changes:

- When disabling PLL, there is no need to call core_write_mmd_indirect
  directly, use the core_write wrapper instead like the rest of the code
  in the function does. This change helps with consistency and
  readability. Move the comment to the definition of
  core_read_mmd_indirect where it belongs.

- Disable both core and TRGMII Tx clocks prior to reconfiguring.
  Previously, only the core clock was disabled, but not TRGMII Tx clock.
  So disable both, then configure them, then re-enable both, for
  consistency.

- The core clock enable bit (REG_GSWCK_EN) is written redundantly three
  times. Simplify the code and only write the register only once at the
  end of clock reconfiguration to enable both core and TRGMII Tx clocks.

Tested on Ubiquiti ER-X running the GMAC0 and MT7530 in TRGMII mode.
Signed-off-by: NIlya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4732315c
  33. 17 3月, 2021 1 次提交
  35. 13 3月, 2021 1 次提交
  37. 27 2月, 2021 1 次提交
  39. 15 2月, 2021 2 次提交
  41. 26 1月, 2021 1 次提交
  43. 16 1月, 2021 1 次提交
    • V
      net: dsa: set configure_vlan_while_not_filtering to true by default · 0ee2af4e
      由 Vladimir Oltean 提交于 
      As explained in commit 54a0ed0d ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.

New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.

Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.

The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.

The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.

Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.

No behavior change except for the added prints is intended at this time.

$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[   60.315148] br0: port 1(sw0p2) entered blocking state
[   60.320350] br0: port 1(sw0p2) entered disabled state
[   60.327839] device sw0p2 entered promiscuous mode
[   60.334905] br0: port 1(sw0p2) entered blocking state
[   60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NKurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>
      0ee2af4e
  45. 12 1月, 2021 3 次提交
    • V
      net: dsa: remove the transactional logic from VLAN objects · 1958d581
      由 Vladimir Oltean 提交于 
      It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.

So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.

It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      1958d581
    • V
      net: switchdev: remove the transaction structure from port attributes · bae33f2b
      由 Vladimir Oltean 提交于 
      Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.

Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8ece ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.

It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.

This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.

In part, this patch contains a revert of my previous commit 2e554a7a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").

For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
  implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
  done mechanically, by pasting the implementation twice, then only
  keeping the code that would get executed during prepare phase on top,
  then only keeping the code that gets executed during the commit phase
  on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
  multicast router could be converted right away. But the ageing time
  could not, so a shim was introduced and this was left for a further
  commit.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NJiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      bae33f2b
    • V
      net: switchdev: remove vid_begin -> vid_end range from VLAN objects · b7a9e0da
      由 Vladimir Oltean 提交于 
      The call path of a switchdev VLAN addition to the bridge looks something
like this today:

        nbp_vlan_init
        |  __br_vlan_set_default_pvid
        |  |                       |
        |  |    br_afspec          |
        |  |        |              |
        |  |        v              |
        |  | br_process_vlan_info  |
        |  |        |              |
        |  |        v              |
        |  |   br_vlan_info        |
        |  |       / \            /
        |  |      /   \          /
        |  |     /     \        /
        |  |    /       \      /
        v  v   v         v    v
      nbp_vlan_add   br_vlan_add ------+
       |              ^      ^ |       |
       |             /       | |       |
       |            /       /  /       |
       \ br_vlan_get_master/  /        v
        \        ^        /  /  br_vlan_add_existing
         \       |       /  /          |
          \      |      /  /          /
           \     |     /  /          /
            \    |    /  /          /
             \   |   /  /          /
              v  |   | v          /
              __vlan_add         /
                 / |            /
                /  |           /
               v   |          /
   __vlan_vid_add  |         /
               \   |        /
                v  v        v
      br_switchdev_port_vlan_add

The ranges UAPI was introduced to the bridge in commit bdced7ef
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.

Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328b ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:

br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink

Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.

In the meantime, commits such as 0944d6b5 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.

Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and  __vlan_add
(the latter coming from commit 9c86ce2c ("net: bridge: Notify about
bridge VLANs")).

That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.

Let's go off and finish the job of commit 29ab586c by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60d
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).

Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.

And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.

Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
      b7a9e0da
  47. 13 12月, 2020 1 次提交
  49. 09 12月, 2020 1 次提交
  51. 05 11月, 2020 1 次提交
  53. 03 11月, 2020 1 次提交
  55. 05 10月, 2020 1 次提交
    • V
      net: dsa: propagate switchdev vlan_filtering prepare phase to drivers · 2e554a7a
      由 Vladimir Oltean 提交于 
      A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
  (the DSA framework just checks for the presence of the .port_vlan_add
  and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2e554a7a
  57. 22 9月, 2020 1 次提交
    • A
      net: dsa: mt7530: Add some return-value checks · 0ce0c3cd
      由 Alex Dewar 提交于 
      In mt7531_cpu_port_config(), if the variable port is neither 5 nor 6,
then variable interface will be used uninitialised. Change the function
to return -EINVAL in this case.

As the return value of mt7531_cpu_port_config() is never checked
(even though it returns an int) add a check in the correct place so that
the error can be passed up the call stack. Now that we correctly handle
errors thrown in this function, also check the return value of
mt7531_mac_config() in case an error occurs here. Also add misisng
checks to mt7530_setup() and mt7531_setup(), which are another level
further up the call stack.

Fixes: c288575f ("net: dsa: mt7530: Add the support of MT7531 switch")
Addresses-Coverity: 1496993 ("Uninitialized variables")
Signed-off-by: NAlex Dewar <alex.dewar90@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0ce0c3cd