Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function hns3_get_tx_timeo_queue_info(), it should use
netdev->num_tx_queues, instead of netdve->real_num_tx_queues
as the loop limitation.

Fixes: 424eb834 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In current codes, tx_timeout_cnt is used before increased,
then we can see the tx_timeout_count is still 0 from the
print when tx timeout happens, e.g.
"hns3 0000:7d:00.3 eth3: tx_timeout count: 0, queue id: 0, SW_NTU:
 0xa6, SW_NTC: 0xa4, HW_HEAD: 0xa4, HW_TAIL: 0xa6, INT: 0x1"

The tx_timeout_cnt should be updated before used.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When wait for response timeout or response code not match, there
should be more information for debugging.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When received vector0 msix and other event interrupt, it should
print the value of the register for debugging.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some statistics for VF reset.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds statistics for PF's reset information,
also, provides a debugfs command to dump these statistics.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit f6b19b35 ("net: devlink: select NET_DEVLINK
from drivers") adds implicit select of NET_DEVLINK for
mlxsw, the code does not have to deal with the case
when CONFIG_NET_DEVLINK is not enabled. So remove the ifcase
and adjust Makefile.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent addition to NFP introduced a function that formats a string with
a size_t variable. This is formatted with %ld which is fine on 64-bit
architectures but produces a compile warning on 32-bit architectures.

Fix this by using the z length modifier.

Fixes: a6156a6ab0f9 ("nfp: flower: handle merge hint messages")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver does not advertize NETIF_F_FRAGLIST, the stack can't
pass skbs with frags lists to the xmit function.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when calculating how much to increment ITR by inside of
ice_update_itr() we do some estimations and intermediate
calculations. Instead of doing estimations, just do the
calculation directly. This allows for a more accurate value and it
makes it easier for the next person to understand and update.

Also, remove the dividing the ITR value by 2 when latency
driven because the ITR values are already so low for 100Gbps
speed. This should help get to the desired ITR value faster.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update driver version to 0.7.4
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code to start or stop LLDP and DCBX in firmware through
use of ethtool private flags.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a new function ice_dcb_rebuild which reinitializes
DCB after a reset.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function ice_update_dcb_stats to get DCB stats
from the hardware and ethtool support for displaying these stats.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a new function ice_tx_prepare_vlan_flags_dcb to
insert 802.1p priority information into the VLAN header
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function ice_vsi_cfg_dcb_rings which updates a
VSI's rings based on DCB traffic class information.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to process LLDP MIB change notifications sent
by the firmware.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the firmware doesn't support LLDP or DCBX, the driver should switch
to "software LLDP mode". This patch adds support for the same.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.

This patch requires a bit of a refactor of existing code.

1. For a MIB change event, the associated VSI is closed and brought up
   again. The gap between closing and opening the VSI can cause a race
   condition. Fix this by grabbing the rtnl_lock prior to closing the
   VSI and then only free it after re-opening the VSI during a MIB
   change event.

2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
   ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
   unset. This results in namespace warnings (ice_sched.o: Externally
   defined symbols with no external references) when CONFIG_DCB is unset.
   To avoid this move ice_sched_query_elem from ice_sched.c to
   ice_common.c.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.

This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.

In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump driver version to 0.7.3
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes typos in code comments.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

By default Flow Control feature is not being enabled in stmmac.

This is a useful feature that can prevent loss of packets and now that
XGMAC already supports it (along with GMAC and QoS) it makes sense to
activate it.

Switch the module parameter to FLOW_AUTO so that Flow Control is
activated.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Finish the implementation of Flow Control feature. In order for it to
work correctly we need to set EHFC bit and the correct threshold values
for activating and deactivating it.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.

We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.

When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.

Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add two macros to simplify reading DPNI options.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the Rx flow classification enable flag only if key config
operation is successful.

Fixes 3f9b5c9 ("dpaa2-eth: Configure Rx flow classification key")
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Preemption disabled at:
 [<ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38
 Call trace:
 [<ffff00000808a5c0>] dump_backtrace+0x0/0x3d0
 [<ffff00000808a9a4>] show_stack+0x14/0x20
 [<ffff000008e6c0c0>] dump_stack+0xac/0xe4
 [<ffff0000080fe76c>] ___might_sleep+0x164/0x238
 [<ffff0000080fe890>] __might_sleep+0x50/0x88
 [<ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0
 [<ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common]
 [<ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0
 [<ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.

Remove the warning by adding a fall through comment.

Fixes: 1c6952ca ("nfp: flower: generate merge flow rule")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
  NIG_REG_P0/1_LLH_PTP_PARAM_MASK
  NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
    bit 1 - IPv4 DA 1 of 224.0.0.107.
    bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
    bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
  NIG_REG_P0/1_LLH_PTP_RULE_MASK
  NIG_REG_P0/1_TLLH_PTP_RULE_MASK
    bit 2 - {IPv4 DA 1; UDP DP 0}
    bit 6 - MAC Ethertype 0 of 0x88F7.
    bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes an error code for an admin queue
head overrun to use I40E_ERR_ADMIN_QUEUE_FULL instead
of I40E_ERR_QUEUE_EMPTY.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the problem with the driver being able to add only 7
multicast MAC address filters instead of 16. The problem is fixed by
changing the maximum number of MAC address filters to 16+1+1 (two extra
are needed because the driver uses 1 for unicast MAC address and 1 for
broadcast).
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Defined the advertised link mode field for 40000baseSR4_Full for
use with ethtool.
Signed-off-by: NAdam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>