Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

I had to add an explicit tag to suppress compiler warning:
gcc isn't smart enough to notice that
len is always initialized since function is called with size > 0.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Most places in vhost can use __get/__put_user rather than
get/put_user since addresses are pre-validated.
This should be good for performance, but this also
will help make code sparse-clean: get/put_user macros
don't play well with __virtioXX bitwise tags.
Switch to get/put_user to __ variants everywhere in vhost.
There's one exception - for consistency switch that
as well, and add an explicit access_ok check.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

vhost/net keeps a copy of the used ring in host memory but (ab)uses
the length field for internal house-keeping. This works because the
length in the used ring for tx is always 0. In order to suppress sparse
warnings, we force native endianness here.
Note that these values are never exposed to guests.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>

Add guest memory access wrappers to handle virtio endianness
conversions.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

We need to use bit 32 for virtio 1.0.
Make vhost_has_feature bool to avoid discarding high bits.

Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>

Now that we have completed 1.0 support, enable it in our driver.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

The spec states that mac in config space is only driver-writable in the
legacy case.  Fence writing it in virtnet_set_mac_address() in the
virtio 1.0 case.
Suggested-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

With VERSION_1 virtio_net uses same header size
whether mergeable buffers are enabled or not.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>

Our buffer length check is not strict enough for mergeable
buffers: buffer can still be shorter that header + address
by 2 bytes.

Fix that up.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>

virtio 1.0 doesn't use virtio_net_hdr anymore, and in fact, it's not
really useful since virtio_net_hdr_mrg_rxbuf includes that as the first
field anyway.

Let's drop it, precalculate header len and store within vi instead.

This way we can also remove struct skb_vnet_hdr.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>

Too many places poke at [rs]q->vq->vdev->priv just to get
the vi structure.  Let's just pass the pointer around: seems
cleaner, and might even be faster.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

If a device appears while module is being removed,
driver will get a callback after we've given up
on the major number.

In theory this means this major number can get reused
by something else, resulting in a conflict.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

It's never declared so no need to make it extern.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Now that virtio-ccw has everything needed to support virtio 1.0 in
place, try to enable it if the host supports it.
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Gracefully handle failure to write device status.
We really should handle other errors as well, but this one is needed for
virtio 1.0 compliance.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The CCW_CMD_SET_VQ command has a different format for revision 1+
devices, allowing to specify a more complex virtqueue layout. For
now, we stay however with the old layout and simply use the new
command format for virtio-1 devices.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>

With the new SET-VIRTIO-REVISION command of the virtio 1.0 standard, we
can now negotiate the virtio-ccw revision after setting a channel online.

Note that we don't negotiate version 1 yet.

[Cornelia Huck: reworked revision loop a bit]
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NThomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Based on patch by Cornelia Huck.

Note: for consistency, and to avoid sparse errors,
      convert all fields, even those no longer in use
      for virtio v1.0.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Based on patches by Rusty Russell, Cornelia Huck.
Note: more code changes are needed for 1.0 support
(due to different header size).
So we don't advertize support for 1.0 yet.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

virtio-blk has some legacy feature bits that modern drivers
must not negotiate, but are needed for old legacy hosts
(that e.g. don't support virtio-scsi).
Allow a separate legacy feature table for such cases.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Now that we use u64 for bits, we can simply & them together.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

set FEATURES_OK as per virtio 1.0 spec
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

For virtio-1, we can theoretically have a more complex virtqueue
layout with avail and used buffers not on a contiguous memory area
with the descriptor table. For now, it's fine for a transport driver
to stay with the old layout: It needs, however, a way to access
the locations of the avail/used rings so it can register them with
the host.
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Use virtioXX_to_cpu and friends for access to
all multibyte structures in memory.

Note: this is intentionally mechanical.
A follow-up patch will split long lines etc.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Negotiate full 64 bit features.
Change u32 to u64, make sure to use 1ULL everywhere.

Note: devices guarantee that VERSION_1 is clear unless
revision 1 is negotiated.

Note: We don't need to re-setup the ccw, but we do it
for clarity.

Based on patches by Rusty, Thomas Huth and Cornelia.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Hildebrand <dahi@linux.vnet.ibm.com>

At this point, no transports set any of the high 32 feature bits.
Since transports generally can't (yet) cope with such bits, add BUG_ON
checks to make sure they are not set by mistake.

Based on rproc patch by Rusty.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

Change u32 to u64, and use BIT_ULL and 1ULL everywhere.

Note: transports are unchanged, and only set low 32 bit.
This guarantees that no transport sets e.g. VERSION_1
by mistake without proper support.

Based on patch by Rusty.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

mic reads sizeof(vdev->features) bits from device, but in fact it stores
bits in local features variable. use sizeof(features) to make code
robust against future changes extending sizeof(vdev->features).
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

It seemed like a good idea to use bitmap for features
in struct virtio_device, but it's actually a pain,
and seems to become even more painful when we get more
than 32 feature bits.  Just change it to a u32 for now.

Based on patch by Rusty.
Suggested-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Reviewed-by: NCornelia Huck <cornelia.huck@de.ibm.com>

The watchdog mask bit offset listed for Exynos7 is incorrect.
Fix this.
Signed-off-by: NAbhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Naveen Krishna Chatradhi <naveenkrishna.ch@gmail.com
Reviewd-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: NVishnu Motghare <vishnum@xilinx.com>
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NDominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org

If kzalloc() failed and then evdev_open_device() fails, evdev_open()
will pass a vmalloc'ed pointer to kfree.

This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where
there was a crash in kfree().
Reported-by: NChristian Casteyde <casteyde.christian@free.fr>
Belatedly-Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.

Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():

    [drm] Initialized drm 1.1.0 20060810
    [drm] radeon kernel modesetting enabled.
    [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
    [drm] register mmio base: 0xC8400000
    [drm] register mmio size: 65536
    radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
    radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
    [drm] Detected VRAM RAM=128M, BAR=128M
    [drm] RAM width 16bits DDR
    [TTM] Zone  kernel: Available graphics memory: 3829346 kiB
    [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
    [TTM] Initializing pool allocator
    [TTM] Initializing DMA pool allocator
    [drm] radeon: 16M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] PCI GART of 512M enabled (table at 0x0000000037880000).
    radeon 0000:0b:01.0: WB disabled
    radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
    [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [drm] Driver supports precise vblank timestamp query.
    [drm] radeon: irq initialized.
    [drm] Loading R100 Microcode
    radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
    radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
    [drm:r100_cp_init] *ERROR* Failed to load firmware!
    radeon 0000:0b:01.0: failed initializing CP (-2).
    radeon 0000:0b:01.0: Disabling GPU acceleration
    [drm] radeon: cp finalized
    BUG: unable to handle kernel NULL pointer dereference at 000000000000025c
    IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    PGD 0
    Oops: 0000 [#1] SMP
    Modules linked in:
    CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
    Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
    task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000
    RIP: 0010:[<ffffffff8150423b>]  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    RSP: 0000:ffff880234da7918  EFLAGS: 00010086
    RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48
    RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000
    RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000
    R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0
    R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000
    FS:  0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0
    Stack:
     ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
     ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
     ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
    Call Trace:
     [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
     [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
     [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
     [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
     [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
     [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
     [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
     [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
     [<ffffffff8156c07e>] r100_init+0x26e/0x410
     [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
     [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
     [<ffffffff81506965>] drm_dev_register+0xb5/0x110
     [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
     [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
     [<ffffffff8141a365>] local_pci_probe+0x45/0xa0
     [<ffffffff8141b741>] pci_device_probe+0xd1/0x130
     [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
     [<ffffffff8163413b>] __driver_attach+0x9b/0xa0
     [<ffffffff816340a0>] ? __device_attach+0x40/0x40
     [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
     [<ffffffff8163378e>] driver_attach+0x1e/0x20
     [<ffffffff81633390>] bus_add_driver+0x180/0x240
     [<ffffffff81634914>] driver_register+0x64/0xf0
     [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50
     [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120
     [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a
     [<ffffffff821dc908>] radeon_init+0x97/0xb5
     [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
     [<ffffffff810e3278>] ? __wake_up+0x48/0x60
     [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
     [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
     [<ffffffff818a78fe>] kernel_init+0xe/0xf0
     [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
    Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
    RIP  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
     RSP <ffff880234da7918>
    CR2: 000000000000025c
    ---[ end trace ad2c0aadf48e2032 ]---
    Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html

I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Tested-by: NPetr Mladek <pmladek@suse.cz>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84627Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org